Software
Houzz Logo Print
jfw432

Belt drive transmission problems

16 years ago

Let me start off by saying that I mow on steep hills. I have a relatively new Ariens mower with the transmatic (I think) transmission. It's not a hydrostatic. I had trouble keeping traction with the normal tires so I switched to knobby tires to aid in traction and felt like I could take on the world with those tires. Shortly after doing this, I started noticing the mower acting like it didn't want to go up hills. In straight or light grades, the mower works well and goes full speed but on steeper grades it will sometimes just not go at all. On the rare occasion, it go slowly up the hill and then in the middle of the hill where the grade doesn't change, the mower will take off and go full speed again. On flat ground, the mower will still give me whiplash if I don't gently ease on the throttle.

So far I replaced the drive belt but that didn't help much. I thought it was the linkages for the accelerator binding or not traveling far enough so I sprayed them with WD-40, everything worked flawlessly for the next hour. The next week all was back to normal and the WD-40 trick didn't work any more. I tried adjusting the linkages to allow for more travel and it made the problem worse in both directions. I'm confused what else could be the problem.

Comments (6)

  • 16 years ago

    I think I've figured out the problem is the CVT belt. It was a very wide toothed belt and I thought it was a cog style pulley but it's a just another v pulley that varies in height to tighten/loosen the belt. I quickly ran some sand paper over that belt to knock the glaze off and it ran very well for a short while.

  • 16 years ago

    If the machine was sold without the knobby tires, and then you installed them, i'd say you have "up-set the apple cart"! You have totally changed the gearing problem. Too much power is being taken up to make the tractor go up hill at the speed you seek.
    Not being an engineer, i can't give you the equations that might solve your problem, the only thing i can see to solve it will probably be getting a geared drive system tractor. Belt drive is ok for most lawn mowing, and pulling a lawn cart, or even a snow blower, but using the tractor for jobs that are way heavier than what it was designed for, i'd say is asking too much.

  • 16 years ago

    Rusty,

    There's BELT drive and then there's BELT drive.

    There are millions of L&G tractors running up hills and pulling 400+ pound rollers that are belt drive and pretty much all of them are belt drive to a hydrostatic transaxle NOT a CVT. John Deere's entire X5xx garden tractor series is belt drive and they pull like you can't believe.

    jfw432,

    Your traction problems are going up hills and on the flat your Ariens does OK so, you bought a light duty riding lawn mower intended for smaller, flat lawns and little else.

    CVT transmissions are light duty and will have problems when asked to do something it was not designed to do... like climb hills.

    Google around and you'll find other people with similar CVT problems and almost always they are trying to do something their lawn tractor was not designed to do.

    You're probably going to need a new wide belt. Sanding the sides is a very temporary fix to any belt that has been glazed. Also, carefully inspect the two pulleys the wide belt rides on. They may both need to have their contact surfaces dressed.

    And just to say it, a little WD in the wrong place can make drive belts lose their mind.

    Since this is a relatively new purchase why aren't you availing yourself of the free warranty service?

  • 16 years ago

    CORRECTION:

    "John Deere's entire X5xx garden tractor series..."

    Should read: John Deere's CURRENT X5xx garden tractor series...

  • 16 years ago

    To Justalurker: Wasn't that mostly what i said?
    RustyJ

  • 16 years ago

    No, it wasn't.

Sponsored