Software
Houzz Logo Print
sfmomof2_gw

Hood Help for 48' Wolf With Grill

16 years ago

Hi,

Thank goodness for this forum. Lately I've been on it all day!

Hoping some experts out there might be able to help me. We've ordered a 54" Wolf all-gas with grill, and I like to cook Asian food. I want a hood that will keep up with me, and my architect wants a stainless steel triangular "chimney" hood with a duct no wider than 12", which throws quite a bit out of the running.

We checked into Modernaire first - unfortunately they do have a distributor here and retailer wants nearly $5,000(!), which is a non-starter for me. : (

Any other ideas/suggestions? Thanks so much!

Comments (8)

  • 16 years ago

    Oops I mean 48" Wolf! Too early in the AM. Could I get away with a high quality 1200 cfm 48" hood? There's a lot more available in that size.

  • 16 years ago

    I have a 36" Wolf AG with grill. You don't say if this is an island or wall mount, the duct run, if a wall mount if there are cabinets on either side, and what hood depths you're considering. All of these will play into cfm requirements. I'm assuming Asian means front burner stirfry. If this is a wall mount and you were to come out to 27" depth such that the front burner is covered, depending on the brand of hood and the volume of the capture area (some hoods have small capture areas while others have very large capture areas) I would think 1200 cfm would be adequate, especially if your range top config has the grill in the center and an inside front burner on which you'll be stirfrying. We have a 600cfm 27"X42" VH, wall mounted and flanked with cabinets on either side and it's more than adequate. A 12" duct should easily meet spec/code for that level of cfms. We discussed our setup with a customer service rep from VH and he was very helpful as we had several issues around mounting and duct size. One caveat: we did a lot of homework on this and we're technically trained--different brands of hoods cannot be compared on cfms alone. There are a host of variables that will affect performance.

  • 16 years ago

    Thank you - it is wall mounted, runs up through house and through roof and there are cabinets on either side. I'm assuming 27".

    Since posting that email at the crack of dawn - I've been up all night stressing about this! - we've switched our order to the 36" Wolf. It just makes the hood too expensive (plus the cost of range itself). So we're now looking at the 27"x42" VAH, 30" off counter. My husband is 6'3", but I'm more worried about smoking up the house than his noggin (is that bad)?

    Thanks for your reply!

  • 16 years ago

    I'm 5'10" and ours is mounted a little under 30" above the cooking surface. We set the height by holding the hood in place and standing to see about head bangin' heights. Actually, when cooking one tends to lean forward so his/her vertical height aspect is reduced. Our VH also has a rolled front edge that hopefully would reduce any serious cranial damage. Depending on the cfms you end up with, I'd check with VH about recommended cfms if you go much over 30" high. The physics of an expanding heated air column are not simple. Had we not had some construction issues that prevented a 10" duct, I would have gone with a 900cfm VH for the overkill, but the 600 has worked out OK. One learning about the Wolf: ours is 6 years old so I don't know how the AG burners are configured now, but to get a good wok char on stirfry I abandoned the wok grate and just place the wok on the small burner cap directly. This literally bathes the round bottom and lower sides of the wok in flames. Btw, the IR charbroiler is a wonderful beast--better and hotter than our outside gas Weber.

  • 16 years ago

    Vent-A-Hood does a lot of custom work. They say they can build anything if provided with drawings. I don't know how expensive (but probably pretty pricey) or lead times required.

    Since you have an architect, if he can produce detailed drawings, you may be able to have something fabricated locally. Many custom sheet metal shops can fabricate custom range hoods to fit around a hood liner. Vent-A-Hood and Fantech (www.fantech.net) make liners in a range of sizes.

    Here is a link that might be useful: Vent-A-Hood

  • 16 years ago

    SFMom: Did you run into the old Modernaire hood guy from Petaluma who literally has everyone up here between a rock and a hard place if they want a Modernaire hood??? Yikes, the whole distributor vs non-distributor thing seems so unfair. it makes me not want to deal with Modernaire. The same hood somewhere else is $3,700.

    I have heard that the optimal height for a few of the hoods that are 1200 cfms is 30-32", almost 6' off the ground if your range is at 37-38". We are fudging a bit and putting our 1200 at 33" off a 38" range. But as you mentioned, not all hoods with the same cfms pull the same.

    Hope you figured out your dilemna! I hear if you use the grill, it does seem to smoke a lot. Have you tried Contractor's Appliance in SF? Julie there seemed really helpful when I called there. Good Luck!

  • 16 years ago

    I got a 48 inch, 1200 CFM Modernaire from Universal Kitchen Appliance in Studio City (ask for Costa) The cost was under 3,000 and they offer free shipping. It's one beautiful hood. Can't comment yet on performance as they are hooking up as I type but it does come highly recommended. I live outside of California so I also saved on sales tax...on all my so called price-fixed appliance. Just a thought.

  • 16 years ago

    Don't worry about headbanging. From experience I can tell you that you only do it once.