Software
Houzz Logo Print
linda_ross8133

Need Immediate Answer!

18 years ago

Yesterday the tile layer had almost completed putting the coils on the floor of the master bathroom. It is a product called Warm Tiles. This bath is new construction so a plywood floor that he is tacking the coils down on and then cover with something and then tiles/grout. As he is almost finished tacking the coils down (this isn't the product that comes in a mat) he said the coils looked larger than he usually puts down and then said this isn't the right product for this application. Now this morning the people from the tile store are coming out to look at it. I am very concerned. Is it safe to have those coils next to the plywood? What if they are really the wrong size? I can see that the tile store would not want to incur any additional costs and would want to go ahead. Are there different products for installation on a concrete floor or plywood floor? Different size units? Do you install the coils directly on the plywood? You are concerned the plywood will get too hot?

Comments (8)

  • 18 years ago

    Does it look something like this? You mention "coils" but when I looked at their website they sell cable systems. We used something similar from Warming Systems.


    If it's similar to this, then you should be okay. This is actually taped to the Hardibacker underlayment, but we also put it down in our kitchen onto the subfloor, and then covered it with Ditra. The wire is designed to be attached directly to the subfloor, whether wood or concrete or cement board.

    Your tiler is using an underlayment beneath your tile, isn't he?

  • 18 years ago

    Yes, that is the way I think mine is supposed to look. They ordered a kit that it too big for the room and instead of the coils like yours they were putting the coils very close together to use up all the coil and even under where the cabinets are supposed to go. They finally took up the coils this afternoon and said the string of coils is just too long.

  • 18 years ago

    Mollie,

    We will be installing the mat system in about a week or so, but everything I have read says DO NOT put heating elements under cabinetry or other fixed pieces. Also, you should not put the cables closer together than the manufacturer recommends, or they will overheat your area.

    I think that it was a blessing that your guy questioned whether the 'cables' were the right size. The way you are describing the job would not have been a good install. The best places to use leftover cable is around toilets and other perimeter areas that are unheated. But most manufacturers recommend staying about 4 inches from perimeter the walls.

    Your User/Install manual should address all of this. Get it out and do a little reading to make some assurances to yourself. Also go to their website and look for the FAQ's or Frequently Asked Questions. Sometimes you can also download installation manuals from the internet, or look at install videos online. Make sure you know as much about the 'install' process as your contractor, even though HE is doing the work. You don't want to have to tear out something later because you well-intentioned contractor may not have been knowledgeable enough. Good Luck.

  • 18 years ago

    Weedy,

    If you are out there, perhaps you should explain to Mollie why she needs an underlayment. Also, did the tape you use come with your wires? Where did you get it?

    This is the first post I have seen of your bath unfinished. That is a very NEAT install, in every way. Was your tub secured in a mortar bed? Do you have finished pics of the rest of your bath? I have only seen it from this angle.

    Thanks, Mommielady

  • 18 years ago

    Your tiler is using an underlayment beneath your tile, isn't he?

    So long as he knows what he's doing, he's fine going over the plywood. Any of you who remember johnmari-- her floor was also done over plywood. Especially with the wire type system that you all are talking about, the wire almost acts as a "rebar" in the mortar that buries it, so it's actually stronger than a regular installation over plywood.

  • 18 years ago

    I said plywood, that isn't exactly right. There is plywood and then over that is that hard cement type of board that the tiler screws down. They told me the mat type of system was a lot more expensive than the coils like in the photo in this thread so decided on the coils. The tiler was experienced in doing this type of installation and glad he said that this just wasn't right. The tile store I don't think wants to eat it that they ordered the wrong kit. They were trying to make him make it work, but it is like twice as big and just no way.

  • 18 years ago

    mollie: We actually had more length of wire than we needed, so we pulled a portion up and moved them all a little closer to each other. The manufacturer says don't put them closer than 2" (3" is the standard), and you definitely don't put them under where vanities will go, but do get under the toekick area. So worst case, they can re-lay the wire, everything a little closer, and use up the wire. If you still have leftover from that, then you definitely need to buy a smaller (i.e., shorter length of wire) kit. As a happy happenstance, the 2" portion is in front of our vanity, and it's a little warmer than the rest of the floor, which is perfect because that's where we stand most frequently.

    mommielady: that's aluminum tape, which came with the kit, but we bought more at the local hardware store. The tub came on wooden legs/slats/base (don't know the proper term) and we leveled them and screwed them into the subfloor. No mortar needed. More pics of our entire whole-house remodel in the link below

    Here is a link that might be useful: Weedy Acres Remodel

  • 18 years ago

    Whoever set the cable did a nice job. Looks clean.

    I use cable from Alcatel and also a while back used some from one of the current "fashionable" companies that has gone past just offering mats.

    When I lay cable, I use the clips. You can buy individual clips that loook like half-circles and nail them one-by-one, they go down fast and the cable goes down even quicker.

    I think it was Alcatel, but they offered clip "strips", you'd nail down a length of clip strip then set the cable. That was even faster.

    Most of the cable I've used is about 3/16ths inch in diameter.

    Aluminum tape? The duct tape of the future!

    Mongo