Software
Houzz Logo Print
caroline94535

Which caulk for around door trim?

16 years ago

We're finishing the inside of my closet. DH has put up the trim on the inside of the doorway, but there are small gaps between the trim and the drywal walls. It's an old, out of plumb and level house.

What is the best type and brand of caulk to run around the edges of the trim, crown, and baseboards to fill the gaps between the trim and walls? Once these gaps are filled I'll be painting the walls and the trim.

The caulk around the outer edges of bathro0m tiles has never cured. It's still soft after several months. I don't know what they used there, but I don't want that same problem in the bedroom.

Thanks for any help you can offer!

Comments (6)

  • 16 years ago

    I prefer Dap's Alex Plus, 35 year, latex (paintable) caulk.

    Be sure to buy a good caulk gun....one that stops when you stop pulling the trigger. It'll make a huge difference in the quality of your work and less wastage.

    The wrong caulk may have been used in the bathroom. Caulk stays soft enough that you can make an indention with a fingernail, but it shouldn't be gooey after it cures.

    Here is a link that might be useful: Caulk info

  • 16 years ago

    I love to caulk! (kind of goofy, I know).
    My favorite is the one annz mentioned, DAP Alex Plus tube looks like this.

    And ditto the good caulk gun. Splurge and spend about $12 on a contractor grade (Home Depot has them in orange, I think they are red at Lowe's). It makes all the difference. Softer grip, smooth squeeze application versus the hard uncomfortable grip, jerky movement of the couple dollar guns.

    Just be sure you're not filling large gaps (it will say on the tube the max size). I generally keep a big solo cup with me (those 10 oz + 'party' size), a little bit of water in it. And a clean damp, but not dripping lint free rag. Rarely use any smoothing tools, just light pressure with my finger (you can wear rubber gloves as long as they're snug). Keep dipping finger or smoothing tool in water, shake drips off, and it helps. Then any excess caulk on my finger after smoothing I just wipe on the rim of the cup. Sometimes it fall down in the cup, if I get too many blobs in the cup I start with a fresh one. It's tempting to use harder pressure, but all that does is just squish it out on the sides, then you have a funky raised edge. Light 'n smooth. ;) Oh, and little drops will happen (maybe onto the floor). Best thing to do is just let it dry and it pulls up on one solid piece. Try to wipe it when fresh and it will make a big mess. (To avoid blobs or caulk coming out gun when I'm done, I release the pressure on the gun about 3" or so from my end point. Caulk will still come out.

    The reason it seems like your bath caulk never cured is because it's all silicone (rubbery texture when dry). I don't like working with that stuff, it's a gooey mess. But some areas, like kitchens and baths where water is involved, it's the better choice.

  • 16 years ago

    I work for a drywall/insulation company and they use the DAP Alex Plus as well. If a professional company uses it, I say go for it-it's good!

  • 16 years ago

    I live in a 60 year old house that has cracks everywhere. They've been repaired several time but they always came back. Finally, I used DAP Dynaflex 230 and the cracks have not re-appeared in 5 years. It's the best stuff ever!

  • 16 years ago

    My cousin used some DAP I had, but in a syringe to fill the voids where he had to cut wall back to get trim to lie flat, and other places where trim wasn't meeting walls b/c the jambs stuck out a little. A syringe makes a tinier bead than any caulk gun could. We didn't even have to repaint the light-colored (Navajo White) walls, the caulk doesn't show at all. I'm *thinking* of touching up along the stair trim since it's a darker color (Thornton Sage) but it's still barely noticeable.