Software
Houzz Logo Print
ludy_2009

Undermount Sink with Stainless Counter??? Help . .

17 years ago

Does anyone have an undermount sink in a stainless steel countertop? There is an ongoing debate about whether it can be done. Any help would be greatly appreciated. There is some thought that only an integrated sink can be done. If you have an undermount -- any issue with leaking? Thanks for your help.

Comments (15)

  • 17 years ago

    The stainless part of a stainless counter is really thin--you can't really undermount a sink properly in it. I've done a lot of SS counter shopping (about to do my second) and it's never been an option. Of course, I never considered it, because I can't think of a reason to do so. Why don't you want it seamless?

    I guess physically, it could be done...notch out the backing material so the sink can sit between it and the stainless skin, uhh...you can probably get anything if you are willing to pay for it I guess!

  • 17 years ago

    ---"The stainless part of a stainless counter is really thin--you can't really undermount a sink properly in it."

    Oh yes you can! We just installed a huge 18 gage German-made ss sink (30 inch + 15 inch drainboard) under a 10 foot long 12 gage ss countertop.

    The trick is to find a competent sheet metal fabricator who can TIG weld the sink and counter together. And to install a wall-mounted faucet. The result is a seamless assembly where germs have nowhere to run, nowhere to hide. The counter practically cleans itself, and sanitizes with a quick wipe of dilute bleach.

    And btw, rather than thin, 12 gage stainless will stop bullets.

    Regards, Fred

  • 17 years ago

    Fred, when you weld in a sink, that's integrated. I don't think that's what she's asking about because she specifically mentioned not wanting integrated.

    And 12 gauge is strong, but still not thick compared to surfaces that are often used to undermount such as 2 or 3 cm stone.

  • 17 years ago

    Alternately, you can treat the metal counter as a solid surface with fully-covered edges and undermount that way, as with my copper counters:

  • 17 years ago

    I think fredl just got to the crux of it. Any SS sink (over or under) can be integrated into a stainless counter. Why mount it when you can integrate it? The thing is, you need to find someone who is good at it or it'll look like crap.

    It would probably cost just as much or more to under-mount because you'd have to have the sink cut-out finished so that it can transition to the sink without a sharp edge.

  • 17 years ago

    Circuspeanut, if you're not willing to come do my counters, stop showing off! :) But I did forget that method, which is of course fabulous on your application but might be strange for stainless on stainless (except it might look OK with an apron?).

  • 17 years ago

    Er... uhm... yeah, finished like that. Sorry, I'm in SS sink mode right now.

    I think that'd be pretty hard to do cleanly with a non apron style undermount, and stainless. I'm no fabricator though, my brother in law is, I do computers, he'd probably tell me that it's no problem and to shut up.

    Also... that counter top is really amazing. I can't look away from it.

  • 17 years ago

    Here's ours! Potfiller not hooked up yet.

  • 17 years ago

    I forgot to mention that my stainless steel fabricator made the sink from the measurements I provided.

  • 17 years ago

    Ha! But Fori, I never said no, did I? Now where do you live again...? If it's warmer than Maine right now, just twist my arm --

    Here's my freshly undermounted round prep sink, done the same way. Neither of my sinks leaks at all - they are placed on a plywood cradle in the cabinet, then the fully-veneered countertop is laid on top and the edge is stuck tight with pure silicone caulk:

  • 17 years ago

    PS: Erika: YUM! Those sink edges look good enough to lick. Which would gross out Fredl, so forget I said anything. ;-)

  • 17 years ago

    erikanh: Would you recommend your fabricators?
    I'd love to put their info in my file.
    That sink/counter looks super! Can't wait to see the rest!
    Amanda

  • 17 years ago

    huango, I was thinking about you the other day wondering if you started your reno yet! I definitely do recommend the fabricator. I worked with Brian DeLano, Vice President of Weiss Sheet Metal in Avon, MA: 508-583-8300. They only fabricate the countertop, they do not template or install. He referred me to Jordan at Aggregate Design in East Boston: (617) 567-1315. If you are a DIYer and you have a simple counter run, you could probably save a good amount of money by doing the template and install yourself.

    Let me know if you need pricing info and I'll look it up for you.

    Erika

  • 17 years ago

    circuspeanut, your skills never cease to amaze. That prep sink/counter looks so great!