Software
Houzz Logo Print
texas_al

What Extension Jambs to Order?

20 years ago

My new house will have 2 by 4 walls with 1/2" sheetrock on the inside ande 7/16" OSB on the outside, plus 1" rigid foam on the outside of the OSB, brick veneer over that, on a 5 1/2" brick ledge. I don't think the brick has anything to do with it, since the windows mount to the rigid foam.

Marvin windows come with standard 4 9/16" jambs. Since 2 by 4 wall with sheetrock and OSB would add up to 4 7/16", I assume this means the window is supposed to stick out past the sheetrock by 1/8". I assume the trim is designed to take this into account.

Since standard is 4 9/16", since I am adding 1" rigid foam, does that mean I need 5 9/16" jambs?

Comments (5)

  • 20 years ago

    Yep, that sounds about right. I did a similar construction with 2x4 walls and 1 inch foam, but went with Thermoply structural sheathing (only about 1/8 inch thick) instead of the OSB. That way I could use 'standard' one-size larger Andersen 5 1/4 inch extension jambs for the windows and avoid some extra trim carpenter work making non-standard extension jambs.

  • 20 years ago

    In general the frame should only protrude 1/16" past your inside finished wall. The 4-9/16" wall thickness is figured with 1/2" OSB as the exterior sheathing. So if your adding 1" rigid foam to a 7/16" sheathing then order a 5-1/2" frame dimension. When we do jamb extensions in the field we order the jamb kits for a 6-3/4" wall shipped loose from the frame. We then field cut them down on a table saw to fit each opening.

    One thing I would recommend is that you trim around the exterior of each window with a 5/4 (1") board to mount the window to. The rigid foam can collapse or smash down when applying the window. This could cause leaks or air infiltration down the road. It will also possibly give you an uneven thickness for your jamb extensions. By mounting the 5/4 board around the opening you have a nice solid surface to mount your window to. You can then butt your rigid foam up to the board. Ounce you've done that you can tape off your nailing fin and seam with flashing tape to finish the job. Good Luck!!!

  • 20 years ago

    I had questioned nailing the windows directly on the foam myself, and I have seen "1 by 4s" used to nail windows to. I have talked to my friend who is acting as general contractor and helping me with the project, and he recommends only using 3/4" foam to leave plenty of room behind the brick.

    He always uses 7/16" OSB, don't know why. Is 1/2" better or more standard?

    If I use a regular "1 by 4" to mount the window to, is that 3/4" thick, and would be flush with 3/4" foam?

    So, basically figure the thickness of the wall and add 1/16"? That would be 5 1/4" with 3/4" foam and 7/16" OSB, or 5 5/16" if I use 1/2" OSB with 5/4 board to mount the window to.

    The only thing bad about the extra board is that this entire perimeter around the window is uninsulated (except for the very low R value of lumber). I wanted the foam for a thermal break between the exterior and not only the studs but also the framing members (bucks?) around the windows.

    One more question: Why should the jambs stick out 1/16" on the inside? Looks to me like the trim won't be flush with the wall if its sticking out.

    Thanks for this good information.

  • 20 years ago

    The 1x4 is really 3/4". So this will match the foam in height from the wall. The best thing to do is cut the 1x4 down to fit just behind the nail fin. You can then butt the insulation board up to the wood. Make sure and back caulk the wood before you nail it on around the window opening. This will prevent any air infiltration. As for the insulation value, you will get that covered when insulating the inside of the window between the window and the framing studs. Make sure and use a "Low Expansion Foam" to insulate around your windows. This will give you the best protection from the elements. Ounce that foam sets up and cures, you'll have just as good a seal as you would have if you put the window over the rigid board.

    The reason for the extra 1/16" is for imperfections and drywall compound. Most doors get some kind of drywall compound around it to cover screw holes. The trim will fit just fine, we do this everyday and never have any issues with it.

  • 20 years ago

    Another reason for the extra 1/16" is that OSB tends to swell. I like 7/16" OSB better than 1/2" because of this. One can still use, for example, a standard 4-9/16" jamb in many applications because the 7/16" grows to 1/2".

    Guy is right on the money (as usual) about nailing the installation fins of the window into something solid rather than foam board. I've seen many jobs where the jamb extensions were for example flush on one side and protruding into the room 1/4" on the other side because of the foam being crushed when the window fins were nailed into it. Yeah wood boards aren't as good an insulator as foam boards, but they're more stable, and after you fill the rough opening cavity with low expansion foam insulation it will be more than adequately insulated around the window areas.

Sponsored
CHC & Family Developments
Average rating: 5 out of 5 stars6 Reviews
Industry Leading General Contractors in Franklin County, Ohio