Software
Houzz Logo Print
lmalm53_gw

Low Voltage UC Lighting System Questions

18 years ago

I will be posting this also on the lighting forum but feel I will get higher volume responses here so please bear with me.

I have 4 old fluorescent UC fixtures in the kitchen... each one has their own wall switch and is hard wired on a 120V system. I want to switch to newer UC lighting, either Xenon or Halogen but am not impressed by the heat generated in the full size strip light fixtures. I am leaning toward the low voltage linear lighting and have been looking at Kichler and Seagull but unsure about what switching to low voltage will mean in terms of my existing light switches.

Do I understand correctly that the required transformer will be connected to my 120V system but its output is reduced to 12V to the linear system? Does this mean I cannot use my current 120V wall switches to turn the UC lights off/on or convert to a dimmer switch at the existing wall switch?

If I want a dimmer on the UC lights will I need to run wire and install a special dimmer wall switch designed for low voltage systems? Are there any linear UC lighting systems that are NOT low voltage and run off standard 120V?

Sorry for all the questions but I am really interested in finding a good quality UC lighting system that meets the following requirements:

1. Good even lighting coverage of UC area.... not the "spotlight" effect of Puck lights.

2. Ability to provide bright task lighting when needed but also can be dimmed to mood lighting.

3. Warmer color light in the 2400-3000k range...no cold blue lights.

3. Would like to control several UC areas by one dimmer wall switch...so need a system that can span between cabinet zones.

If this is not possible, can I still use the 4 wall switches I now have but just upgrade to dimmer units? I am unclear on what is involved in converting the current 120V Off/On wall switch to a low voltage dimmer. Since I am replacing existing UC fixtures was hoping not to do major rewiring.

I would love to hear from any Kichler or Seagull UC lighting owners. I'm a noob when it comes to electrical so forgive if my questions seem a little dense.

Comments (5)

  • 18 years ago

    I have Seagull low voltage linear xenon lights under my cabinets and I love them. They were wired in to a single junction box in the basement ceiling then to the transformer (or maybe the other way around!?) and to a single switch by the sink. I think, if you use your existing light switches, you will have to have 4 transformers.

    I didn't make the decision to use these lights, I just told the KD I didn't want halogen and I wanted all the lights to switch on from one switch. She did a good job.

    I have a normal switch with a dimmer, nothing special. I think all the transforming between 120V and 12V takes place at the transformer.

    You can see the lights mounted in this picture. I have never used the dimmer.

    It's a wonderful lighting system, it gives good, clean light, doesn't heat the cabinets up and in 4+ years, I haven't had a single bulb burn out.

    Good luck.

  • 18 years ago

    My personal preference has always been LV UC lights. We currently have two stings of Seagull Ambiance each with it's own transformer which are on dimmers. We rarely run them at full power.

    The dimmer will replace your switch, just be sure it is one that can be used with transformers.

  • 18 years ago

    Thanks for the responses! It reinforces my belief that Seagull is a good system to go with.

    I just called their Tech Support and was told that I can use my current 120V wall switch wiring with a new dimmer switch that feeds electric to the transformer. The transformer then outputs 12V electric to the actual lighting system.

    The transformer can handle 2 line input for the track wiring so if I place an electric transformer in the middle of my L shaped cabinet area I can run the lights to a distance of 10 feet either side of the transformer before there is any wattage dropoff. The electric transformer has a max 150W load which should be more than enough for what I need on the that portion of my kitchen. Larger spaces need to use the magnetic transformers which carry higher loads and allow longer wiring tracks for lights. I hear that electrical is better than magnetic though if you can go with the load and length restrictions.

    My desk and butler pantry areas which are across the room will still need separate transformers and switches but that is acceptable to me. So I hope to start out by installing the Seagull system in my kitchen cabinet area first and see how I like it. Then will add the other 2 areas at that point.

    I still appreciate any additional input, comments or personal experience with this or similar systems. Love the information that comes out of these forums. It has saved me many times from making wrong decisions, plus it sure helps me to focus on issues I would otherwise not even be aware of. Thanks!

  • 18 years ago

    I would use the magnetic over the electronic. Have used both, find the magnetic considerably more reliable, and less likely to give electrical interference.

  • 18 years ago

    Just ordered my Seagull Ambiance low voltage lighting system today. Went with the electronic transformer primarily because it is smaller in size and allows me to hide it more easily plus the sales rep is pushing electronic over magnetic. I hope to get it installed within the next 2 weeks so I will report back how it all works out. Thanks for all the input!