Software
Houzz Logo Print
mommyto4boys_gw

DIY wood counters

15 years ago

We are currently finishing our lower level for resale purposes only. The budget is next to nothing if ykwim!!! It will have a small kitchenette/bar area. I have decided to get unfinished oak cabinets from a box store and stain them as black a I can get them. DH is building the bottom of the penisula/bar area out of bead board and it will be black stained too. We will have a hickory like laminate underneath. There will be NO uppers, I'm planning a mirror wall with open sheleves and a little bling with glass tiles around the mirror and for a backsplash. How does that all sound??? Then I'm thinking of going with a stained wood counter made from maple? We are thinking of doing this ourselves too? Ikeas is too far to get there again for just counters. Anyone do this themselves? Dh is extremely handy & doing the basement himself too. Just hoping to not add too much more to his to do list. However, I'm thinking we can get a very, rich nice look the least expensive way by diy wood counters?! The main floor has all granites, marbles etc in all the baths and kitchen, etc. I think we have to stay away from laminate to "match" the rest of the home.

Comments (16)

  • 15 years ago

    Making your own wood counters is a tricky project. You'd need several pretty costly and complex tools that your average homeowner doesn't have. You'd need a joiner, a thickness planer, a lot of clamps and some experience using those tools. Using a birch plywood with solid wood molding for th edges would be much easier and cheaper. Birch and maple are also pretty difficult to stain, so you might consider leaving them natural to contrast with the black cabinets. Or, an even easier project would be a tile countertop. Use your glass mosaic tile for the counter, or a granite tile, or just a plain simple tile. Or, there's always Lumber Liquidator's butcher block countertops.

  • 15 years ago

    We used birch plywood and poplar trim stained red mahogany on our bar. We used two sheets, and offset them to have a gutter area on the bar. We finished it with Waterlox, and they are gorgeous.

  • 15 years ago

    cocontom, can you post pix? Did you use 3/4" plywood?
    I've been trying to figure out what to do for our countertops for a while now. Since I'm trying to restore the kitchen to its 20s bungalow roots, I don't actually want butcher block, I want solid wood or wider face grain. But, it is basically impossible to find a solid plank of decent wood in a 25" width anymore (or cost prohibitive, for sure). I think good baltic birch plywood with solid wood edgings might be an option, I have seen what I believe is something similar at some local restaurants for table tops.

  • 15 years ago

    badgergrrl, I looked into this for our kitchen, also since IKEA is far away and I'm on a budget. However, solid wood in a countertop size could warp (at least, according to folks on woodworking forum). I also looked into doing plywood over my current countertops, but was told it's not a good idea around a sink (possibly even worse than the usual wood countertop warnings). I'm now planning to buy sheet laminate and resurface my counters, but that doesn't help you with an historic bungalow.

    The woodworking forum isn't quite as active as the Kitchen forum, but there are some knowledgeable folks there who could probably better answer your questions. Also try searching for plywood countertops. There have been a few threads around here.

  • 15 years ago

    Sorry! In scrolling up & down I managed to get OP & badgergrrl mixed up, thinking it was the same person.

    To add to what I wrote above...I don't know what your market is, but I know I've seen homes with granite in some areas and laminate in others, where the laminate didn't feel cheap and unmatched. They make some nice looking laminates now, and if you're willing to diy, it's incredibly cheap.

    I also recall a friend's dad building their downstairs bar countertop with a big log slab. He finished it with envirotex, which is what they use on bars and restaurant tables.

  • 15 years ago

    well, solid wood has worked for almost a hundred years in many kitchens, but it was a much higher quality (read: denser, old growth) wood to start with - that's just not available any more, practically speaking. (As an aside, we pulled off some of the window trim this past weekend to repair some siding and I almost dropped it. It was way heavier than I had expected it to be for a piece its size. Also had the lumber yard written on it on the back in pencil in beautiful Palmer script, I took photos before I put it back. Sorry, I dork out over this kind stuff.)

    I do visit the woodworking forum, and have seen the posts. I am not worried about the water. I would edge the plywood which I think would minimize water, and I had planned on using Waterlox, as many have used successfully on their wood countertops. I think the concern with water and plywood is delamination and rot, but if you start with a solid core hardwood plywood, I would think that wouldn't be as much of an issue. Now, using C grade with voids and pulp fill, that might be a problem. I'll continue to research, but I would be curious to hear what cocontom used.

    I did look into veneer, but much of that was more expensive than medium grade butcher block. Laminate anything is not an option for me. It's up there with vinyl siding and replacement windows on my ick factor. (But, I'm admittedly an old house snob. lol.) Granted, I have laminate countertops currently, but hopefully, they'll be gone soon.


    OP, have you looked at granite or polished tile? Specifically, 12 or 14" square? I have seen them done on countertops before (in person, not just on HGTV ;0) and they looked quite attractive. They used minimal grout spacing and same color grout. No one would mistake them for solid surface, but they looked nice especially given the price. For a lower level, secondary space and/or for resale, it might be a good option for you?

  • 15 years ago

    I'm not sure we ever took final pictures- I certainly can't find them, but here are some of the "work in progress" shots. The top is 3/4 or 1/2 birch ply from Lowes, we don't remember which.

    This one is the most finished- the step is now finished with a mahogany stained tread and the woven mat on the front (I'm pretty sure the mat wasn't even attached at that point), and the corner has a mahogany stained piece on it as well.

    This one shows the gutter/back end. We didn't notice until this shot that we got the wrong corner pieces, and by that point, we were too far in to care.

  • 15 years ago

    cocontom, that looks nice. What kind of trim did you use on the edges? Did you get it at Lowe's also?

  • 15 years ago

    badgergrrl, have you seen Bungalow Kitchens by Jane Powell? That book gave me serious home envy. Lucky you, to get to be an "old house snob"! ;)

  • 15 years ago

    I have seen it - I can see it from where I'm currently sitting. ;)

    I also have her Bungalow Bathrooms, Bungalow Details: Interior and Bungalow Details: Exterior books. They are all excellent. I know some don't care for her writing style and acerbic sense of humor, but they are right up my alley. Even if you don't care for her, I recommend them for the pictures alone.

  • 15 years ago

    Thanks for all the responses and the great picture (cocontom). DH does have the tools and the skill to do the counters. I think we will have to price out the wood to see how much it will cost. Lumber liq's was an option I thought of and checked out too. They are priced well, but still too high for my "pennies" budget. I'm thinking for the time to install tile or the granite "tile" counters, dh could probably make the wood counters. Though I'm the one who always under estimtes the difficulty factor and time needed for all of our DIY projetcs. I'm definitely going to check more on plywood and trim. Would love to see more pictures! Thanks!

  • 15 years ago

    You could laminate two pieces of plywood together and stain/do some faux finishing to look more grainy and stain/ply more. That would work. Then add the trim. Or.... tile would be real cheap.

  • 15 years ago

    Marti8a, it's two pieces of crown molding, one flat on top, just overhanging enough to cover the top of the vertical piece, quarter round on the wall, and the corner things. They all came from Lowe's.

    We looked at real bar rails, and they were going to be more expensive than everything else combined. I don't think we spent more than $200 on the whole bar including cabinets.

  • 15 years ago

    mommyto4boys - I don't have any pics in my inspiration file anymore, but here are some links with pictures (not all as cool as cocontom's):

    plywood-the-best-cheap-kitchen-countertop

    plywood-kitchen-countertops

    diy-idea-plywood-countertops

    wood-counter-tops

    How to Build Your Own Wood Countertops

    Inlaid-Wood-Countertop

    Eye Candy

  • 15 years ago

    OMFG jessicaml - thank you, thank you, thank you! One of those links included a comment with a mention of craft-art.com 's homeowner DIY plank countertops that someone used. This. Is. Awesome.

    They're a little more than IKEA's, but they're what I want and not too expensive. (Meaning: not expensive enough to go to the trouble of the plywood.) Plus, they actually have them. I've heard tell of months until IKEA has theirs back, and even then, they were edge grain.

    Here is a link that might be useful: Homeowner DIY countertops

  • 15 years ago

    lol glad to help, badgergrrl! I checked out Craft Art's page, truly beautiful stuff. Something to keep in mind if I have a dream home someday. :) I hope you'll post pics when it's all done!!