Software
Houzz Logo Print
moovie

Almost there, but AAAAUUUGH!

18 years ago

I've only posted here a couple of times, but read these boards constantly. Really need to vent a bit, and I know you'll all understand.

Floor has gone in and is ready for finishing (Brazilian cherry with a commercial water-based finish). Not too many problems, but there are grease spots, etc. that need to be sanded out before finishing.

Cabinets went in over the last two days. They are beautiful - clear alder with a cherry stain. Handles are stainless steel with just a nice curve. Very contemporary and we really like the way they look. But!

Hubby and I took a night away, went to a concert and had a nice night at a hotel an hour or so away from home. We got home today (Saturday, so no workers on site) and found our island has been installed 2 inches off-center, and the recessed lights (placed by hubby at the direction of architect/designer) are right up against the crown molding of the cabinets on one side of the kitchen. Oddly enough, the same narrow side of the island. We finally figured out the architect drew the original plans with 24" cabinets on that side, and they are actually 26" deep.

So now we need to move the island 2" to center it, and the lights should be moved as well. Ceiling has already been finished, so there's another issue! Moving the island will most likely leave nail holes in the cherry flooring. Plus there are dings and nicks in the cabinet finish from installation. AAAUUUUGGGH!

We paid big bucks for this remodeling firm. Are we out of line for expecting them to fix the light placement and ceiling patches at their expense? How much can we expect the cabinet maker to fix on the doors? (One is an appliance garage door with a nick on a corner that will continue to get worse if the door is not adjusted to clear the support bracket when the door is raised up.)

Thanks!!!!

Comments (3)

  • 18 years ago

    How wide are the aisles around your island? As long as they're not the bare minimum, it's probably not noticible to anyone but you that the island is off center. I would carefully weigh the benefits of moving the island against having to deal with repairing the floor.

    Now the lights...those may very well look bad right up against the crown, and you might ask your architect/designer to absorb the cost of them getting moved. The cabinet maker should take care of the door issue for you.

  • 18 years ago

    Who did the lighting plan? THe architect or the remodeling firm? DId they consult the KD about the size of the cabinet crown molding you intended to use, or was the decision about the size of the crown molding a later decision after the lighting was done? (In other words, did your KD measure where the lights were before the molding was suggested, or was it vice versa?)

    Who approved the increase in size of the cabinetry and was that communicated to the architect and the remodeling firm both? THe GC is the one who coordinates all of the trades, but if there isn't a two way communication from everyone, he's gonna miss a few things and have to correct them later and then charge them to the trade that caused the issue. I'm sure he'll fix the problem first and lop heads later. That's what you pay a remodeling firm for!

  • 18 years ago

    Thanks for the responses.

    alku08 - Clearance on one side of the island is 38", the narrow side is about 34". The whole reason we started this remodel was because we had clearance issues with the original island and an oversized refrigerator. I fought to keep the island (hubby hated the original), so now this is kind of a big deal. Granted, we removed an outside kitchen entrance, so there is less traffic, but 34" is pretty tight. (Fridge is now a cabinet depth, french door model).

    live_wire_oak - Architect represents the remodeling firm and acted as KD. (Yeah, I know, but we were such babes-in-the-woods about remodeling that we didn't know there is a difference between an architect and a KD.) Architect sat in on the meeting with the cabinet designer and actually pushed us toward the bigger molding (which looks fabulous). Unfortunately, that decision was made after the lighting was done. Not sure where the error in the cabinetry size was made. Halfway into the process, we had to change cabinet makers, so had to have a new set of drawings done. I signed off on the drawings, but they only had one cabinet marked at 24" depth and I see where they brought the rest of the cabinets out to 26" but didn't mark them as such. The 26" cabinets are housing the built-in ovens and the fridge, so they need to be that deep. All we know is that we agonized over the placing of those lights, wondering if they were correct, and finally going with what the architect said, because he's supposed to be the expert.

    At this point, we are bringing everything to the attention of our project manager, who seems to be a pretty good guy. I just wish we had ONE aspect of this project that didn't have something go wrong with it (starting with needing a variance to replace the deck, then having the electrical feed to the detached garage cut when they dug the footings, the original cabinet maker having a fire in his shop halfway into our project, having to recall the carpenter and his crew to fix several errors on their parts, then this stuff, PLUS the guys who installed our rain gutters while we were gone this weekend decided we didn't need as many downspouts as the plan stated and left one off.) I know it will all turn out fine, but I am so frustrated!!!

    Please tell me it will all be fine so I can go to bed and sleep well! :o)

0