Software
Houzz Logo Print
joseph_corlett

Witch Hazel Walks Into A Bar...

11 years ago
last modified: 11 years ago

Witch Hazel Corian walks into a bar and sees Rabbet, Butt,
and Miter joints sharing a pitcher of beer. She cozies up to them and says,
“Which one of you boys can make my edges look the best?”

Miter says, “Ma’am, I am the method recommended by your manufacturer, DuPont,
in their Veined Esthetics Fabrication Manual.”

Butt knows Miter is right, and although he’s in the manual too, he’s not
recommended. He can be one of the faster of the other two, therefore earning fabricators
more money, but he’ll leave the 12mm depth of Witch Hazel’s sheet edge exposed
like he always does and her sheet edge can deviate noticeably from her deck when
profiled. He’s flawless on consistent particulates, but no good with veining
and therefore stays silent.

“Hold on, little lady,” says Rabbet, “I’m not in the manual,
but there’s been a few of my types that have revolutionized your momma’s fabrication
that weren’t either. You can thank fabricators for inventing thermoforming and
hard seams. No disrespect to Mr. Slocum, your momma’s inventor, but the lab
rats that wrote that manual never had a fussy lady customer to please and
payrolls to meet, hence the fabricator’s creativity and taking license with the
rules.

Miter does make a fine edge, but he’s dangerously sharp and
delicate during fabrication. If he’s not taped and coming off a hundred-thousand
dollar V-Groover and Bubby gives him a whack moving him from the machine to the
bench for glue-up, let’s hope the repair is invisible or he may have set a
sheet of you on fire, metaphorically speaking.

Miter is a handsome joint, but even when he’s perfect, he’s
still always at eye level to humans looking down at him, unlike me. My joint is
always facing out, not up, making it much more difficult to see. He can’t be
easily thermoformed around a corner, but I can.”

Miter interrupts “Hold on son, my joint may always be facing upward, but
because of my perpendicularity to any edge profile, I’m not subject to glue
line elongation, as are you.”

“Sir, I concede your point,” Rabbet replies, “but I think your concerns are
more theoretical than practical. I look good no matter the profile as long as
I’m fitted and clamped tightly and utilize a more opaque adhesive. I have more
adhesive area than you, probably making me stronger.”

Turning back to Witch Hazel, Rabbet continues, “DuPont
recommends Taupe as your adhesive, but the boys at Glue Warehouse recommend
Sheer White. There’s a fabricator in Florida that’s says you seem to respond to
Oxford White, Stealth, and Canvass White equally well. He’s got the joints to prove it although he
usually always follows the manual to the letter. I like girls that, like me,
aren’t too fussy.”

Rabbet grabs a bar napkin and illustrates his points:

“Miss Hazel, I knew your veined mother, Verona White, and
made her look great too. Bless her discontinued soul” says Rabbet.

Her car keys in one hand, Witch Hazel gently clasps Rabbet’s
hand with her other and gently pulls him toward the door. As they walk away,
Rabbet turns and winks at his wingmen and they give him a thumbs-up
simultaneously.

Comments (20)

  • 11 years ago

    I haven't been on the forum since the changes hit, and when I read this I thought, "Boy, someone is giving Treb a run for his money..."

    Then the light bulb went on.

    Good stuff.

  • 11 years ago

    Plot, character development, and education all in one package. What more could you ask for? Great writing, and helpful!


  • PRO
    11 years ago

    Thanks, everyone.

    This is my token gift of goodwill toward Houzz since taking over Gardenweb. As readers may or may not know, I write a column professionally and struggle with whether or not to post here for free or submit the piece as a column and get paid for it. Once it's published here, I can't submit it at www.countertopiq.com. I am a month ahead anyway. Enjoy.

    I made a medium screw-up on this job and fixed it flawlessly. I don't know if that's a whole column or not. I do love the catharsis of confession.

  • 11 years ago

    I hope you know how many folks appreciate your contributions here. The help you generously provide is part of the glue that keeps this community together.

    Based on your past threads, I am kinda having a hard time believing you made a small screw-up, let alone a medium one...!


  • 11 years ago

    Treb, you continue to fascinate and amaze.

  • 11 years ago

    Tee hee, I enjoyed the read, and the education!

  • 11 years ago

    Holy moly.

    Truly, I'd have loved to see your screw up, before and after. Simply because I'm sure to most eyes, your screw up would have been perfect.

    Out of curiosity, Can you publish your article, then copy it here? Or does it become their property. Could you quote yourself? I don't know how it works if it's you. If someone else is doing it, copyright infringement is very clear.

    Good to see you.

  • PRO
    11 years ago

    CEFreeman:

    www.countertopiq.com pays for the right to be the first to publish my work. Just like the supermarket, fresh has value. I retain my copyrights.

  • PRO
    11 years ago


    Solid surface sinks are adhered to the back of a full sheet. When the adhesive is cured, the top is flipped, a hole is cut through the top inside the sink area, a router bit is inserted in the hole and the nylon protected bearing on the bit rides along the inside of the bowl, cutting it out perfectly. Another bit profiles the edge the same way.

    Using a straight bit with no bearing to cut the initial hole, I mistakenly uncovered the sink flange as shown here. If it had been any deeper, I would have destroyed the bowl. The reason I cut so close was to maximize the size of the sink cut-out that had to be turned into side splash for this job. I plunge cut into the front sink corners for this very reason. I don't want anyone to see the repair every time they use the sink if this happens.

    Sometimes the nylon falls off the bearing for no apparent reason. That's really fun.


    This is a piece of veined Witch Hazel ground to fit in the edge profile and adhered with color matched adhesive.


    The edge is re-profiled and sanded. And no, a customer would never be told of this.

  • 11 years ago

    Wow, that's truly impressive! (Both the story and the repair.)Reaffirms Corian as my next countertop. Love the integrated sinks and the look of Witch Hazel.

  • 11 years ago

    Loved the story treb!

  • 11 years ago

    I didn't put 2 & 2 together at 1st, but then crcollins said the light bulb went on & Bam, I knew it was you! Great story & fun lesson. I believe mudhouse said something about how your so generous with your knowledge & one of the many people on here that helps to keep the community together. So true & greatly appreciated for all of it. Especially nice to see you after such a big change on here.
    I was a little worried that we might have lost that wonderful community of all of the generous & charitable help. But, I think it's all coming back. I, for one, am glad to see so many of the regulars on here.

    Thanks again for a fun story Treb.


  • 11 years ago

    +1 mudhouse and bicycle girl.

    This was funny. I too was confused how anyone could be writing with such authority other than Treb. I hate this changeover from the old easy-to-use site. But I have beautiful Corian countertops my house thanks in part of the Qs&As of Mr Trebuchet.

  • 11 years ago

    Love Corian. Love Witch Hazel. That was a good one, Treb.

    Joseph Corlett, LLC thanked MizLizzie
  • PRO
    11 years ago

    It's "Venaro White Corian" not "Verona". Geesh.

  • PRO
    11 years ago

    Hi Joseph Corlett, LLC - thanks for the story!

    I was wondering what your views where on rabbetting (is that even a word?!) a Neolith surface?

  • PRO
    11 years ago

    Hianta Cassam Chenai Interiors:


    I think it'd be a great experiment. I've never done it and don't know anyone who has. Like most things, you've got to find a fabricator who isn't married to "but we've always done it this way."

  • PRO
    11 years ago

    Thanks Joseph Corlett, LLC. We shall see what my fabricator says!

  • 11 years ago

    Well wow, this has all been instructive. First, regarding this change -- I too have been gone awhile and am wandering without a rudder. It's different here on GW, way more awkward to post yadayada and I have no doubt at all this has been discussed to a faretheewell.

    But this is a great introduction to the new GW, including the old worries about our counters! Them was hard decisions and I've made my peace with it all. Very funny story, and very helpful. I still regret mightily having put in (and paid the upcharge for) a fancy island edge ... sigh. A little information goes a long way, :)

Sponsored
AIS Renovations
Average rating: 4.5 out of 5 stars15 Reviews
Custom Craftsmanship & Construction Solutions in Franklin County, Ohio