Software
Houzz Logo Print
bbstxx

How to check refrigerator temperature

11 years ago

The on-the-door temperature read-out says that my refrigerator is 36 degrees. However, my instant-read thermometer when left in the fridge for 20 seconds just sitting on one of the top two shelves says it is closer 51 degrees. My infrared thermometer when held against the interior wall reads 48 degrees.

My instant read thermometer when inserted into the milk carton says my milk is 44 degrees.

This all got started this morning when I took a pound of sausage out. When I cut the package open, I could tell the sausage was spoiled. It was still in-date. I got a second pound out. It smelled bad too.

The refrigerator is a 15 month old GE Cafe side-by-side. The milk is on the top shelf. The sausage was in a bottom drawer that is labeled "Express Chill." The instant read thermometer reads 55-56 degrees in that drawer.

Is there some other way I ought to be checking the temperature?

Today is Sunday. Tomorrow I'll call a repairman, but is there anything I ought to do now?

Comments (27)

  • 11 years ago
    last modified: 11 years ago

    I have already plunged my instant read thermometer into the carton of milk. It read 44 degrees. What would a more proper thermometer be?

  • 11 years ago

    http://www.amazon.com/dp/B0000AQL26/?tag=cioequippilot-20


    Be careful with that food because it's in the danger zone!

  • 11 years ago

    I know. I think I'll have to pitch everything but the canned drinks! Luckily, there isn't much in there right now except condiments, although I do have some prosciutto and some cheeses. To replace everything will be a couple hundred dollars.

  • 11 years ago
    last modified: 11 years ago

    bbstx - better safe than sorry: pitch the perishables, IMO.

    PS From quick googling of reputable sites, milk temp shouldn't exceed 40 degrees.

  • 11 years ago

    I have the same issue with my 18-month old Electrolux. It isn't quite in the danger zone, but very frustrating. They replaced a bunch of parts to no avail. The panel is set for 33 degrees but thermometers read 38. Good luck.

  • 11 years ago

    Thanks, y'all. I feel snake-bit. My GE Cafe all gas range is a awful. The Kitchen Aid dishwasher doesn't perform to my standards and has already had to have a door spring replaced. And now the fridge has gone wonky. At least the range and DW problems started while they were in the warranty period. The fridge waited until the warranty had expired!

  • 11 years ago

    So sorry to hear about your appliance frustrations...no fun (been there, done that). It's because 'they don't make 'em like they used to' that I want so desperately to hang onto my 24 y/o electric coil cooktop and built-in oven/micro, despite an imminent reno. Everyone says I'm being goofy.

    Since your fridge is out of warranty, maybe do some side reading that might save you some $ in repairs. I see that GE has a 'fridge not cooling' troubleshooting section, so maybe that'll help. We had an issue years ago with our fridge bulb not turning off even when the door was closed. I remembered opening the door first thing in the morning, brushed my hand near the bulb, and noticed it felt awfully warm for the fridge having just been opened. Those bulbs get pretty warm (thought I don't recall it dropping our fridge temps that much -- maybe we caught it early).

    Double check your warranty -- maybe certain parts go beyond that first year? Good luck.

  • 11 years ago

    Post the model number of the fridge and we can check the warranty. Until very recently, "Most Fridges" had at least a 5 year warranty on the sealed system, some even longer.

    The "Sealed System" would be the compressor, evaporator, condensor and tubing .

    We have seen some "Cheapies" (Might be Whirlpool) that only had a one year warranty but far as I know this is NOT the "Norm", even with other "Whirlpool made fridges" IE, Kitchenaid, Jennair, maybe Maytag.

    You can also download the operators manual, assuming you can't find yours, and usually towards the end of the op manual, they spell out the warranty, what's covered and for how long.

    Gary

  • 11 years ago

    Yes, the fridge is bad if meats get spoiled. However, carton beverages (OJ and milk have been mentioned) tend to be UHT-pasteurized, which prevents spoilage at room temperature even if left out for a couple of days. You have to introduce active live forms to make them go bad.

    The reason they're usually kept cold is mostly consumer perception.

    There are producers who sell simple-pasteurized milk, that would go bad if left at room temperature. You can usually tell if it's the case by either markings on the package or the fact that the expiration date is no more than a week in the future, while the UHT one is one to two months ahead.

    /RANT


  • 11 years ago

    CZS25TSEBFSS is the model number. According to the manual, GE Profile has a 5 year warranty on the sealed system and the compressor. "GE and all other brands" have a 1 year warranty on the sealed system and the compressor.

    When the repair place opens in an hour, I'll call them.

  • 11 years ago

    Good luck! It's a good reminder for everyone to keep a thermometer in their fridge just to be safe and have assurance that the food is being kept cold enough.

  • 11 years ago

    Calibrate your instant read thermometer. Fill a glass with ice and water. Give it a few moments to cool down. Place thermometer in the super chilled water. Take a reading. It should read 32 degrees Fahrenheit or 0 Celsius. You will be able to tell how far your thermometer is off. Now place it in the back of the refrigerator for a little while. Take a reading. You will get a better idea of the situation. I always keep a thermometer in the back of the refrigerator and one in the freezer. It's a double check of the system. Good luck.

  • 11 years ago

    Proper ice bath to check thermometer accuracy:

    http://www.thermoworks.com/blog/2010/10/making-a-proper-ice-bath/

  • 11 years ago

    Thanks for the tips for calibrating a thermometer. Mine has recently been calibrated, so I know it is accurate. In addition to the thermapen, I've also used an infrared thermometer to gauge the temperature of the walls and shelves.

    Now I'm trying to find a repairman who can get here sooner than next week.

  • 11 years ago

    Refrigerators, especially frost free models swing in temperature a lot. (8-10 degrees is pretty normal). In the lab we put a thermometer into a bottle of liquid-- for long term use we use mineral oil, but water is fine. If you use a pint jar or so that will average out the short term variation to give you a reasonable average. Your milk is also a good indicator, though if it's in the door keep in mind that the door temps can be 5-10 deg higher than the interior of the fridge (so the door is actually a terrible place to keep your milk). If you want to really see what's going on you can get a digital recording thermometer or a USB temperature logger to take minute-by-minute readings.

    All that said, the sniff test is pretty reliable, and you have a problem. The first thing to try is to vacuum off the coils, poor air circulation in the heat exchanger can cause exactly the problem you're having, and is the most common cause.

  • 11 years ago
    last modified: 11 years ago

    bbstx:

    Numbers of things could be wrong. Ones that are easy for you to diagnose and/or fix yourself.

    1. Might be dust and crud build-up in the compressor compartment. As rwiegand says, vacuum it out. (Might have to unscrew and dismount a cardboard or metal panel on the back to get at the area. Do you have pets who shed a lot? Might have to do this a couple of times a year)
    2. Most likely culprit is ice build-up on the evaporators or the fans. Ice build-up is the result of excessive humidity. Do an old fashioned manual defrost. Turn the fridge off. Take out all the food (apparently already spoiled, anyway). Prop the door open and run a floor fan for hours (overnight would be good.) Check inside and under the fridge every few hours to see if any melt water is pooling. (If you had a lot of ice build up, you could see a lot of water and you'll want to avoid overflows onto the floor.) Then plug the fridge back in, wait a few hours for it to cool again, and then and see if it will keep a glass of water cooled to 37°F. If that fixes the problem, check to see if your fridge has some kind of humidity control button or switch. (Some do, some don't.) If you have it, you may need to switch the control on in the spring and/or summer.
    3. A related culprit could be ice or crud build-up in the defrost drain line. If the line plugs up, it can cause ice-buildup on the evaporator and fans. If it iced up, the manual defrost may clear it. If you have crud build-up, you may want to have the tech clean it out for you.
    4. A broken fridge-light switch can also produce problems because the lights can warm the fridge when left on. (Heck, there was a batch of LG fridges a few years back where defective light switches overheated the interiors because the lights never went out. Some of those fridges even caught fire!). Push the rod/tab in and see if the light(s) goes(go) out.

    Expanding on what rweigand and everybody else said, here's my contribution to the description of temp testing. My fridge is a 3-year-old Kitchenaid. I have the temp control set to 37°F. Using more-or-less calibrated probes (a Thermapen and a couple of wired probe models), the food on the main shelves (milk in cartons, jarred foods, solid items (say, cucumbers), etc. will pretty much always be between 37.2°F and 38.3°F (items at the back of the shelves being slightly cooler than those at the front edge.)

    Items in my fridge's door racks will be around 43°F which is fine for the kinds of items stored there. For example, mayo is sufficiently acidic to prevent unwanted bacterial growth. For the reasons cited by gigelus2k13, the door is okay for store-bought milk and butter, too. However, my experience is that dairy items stay fresher, longer in cooler parts of the fridge. That will be a consideration for low turnover dairy items.

    Food in my fridge's crisper drawers always seems to be around 40°F. That's great for whole produce and okay for most peeled or cut produce. My fridge has a "deli drawer" with its own temperature control. Food in that drawer measures between 34°F to 35°F.

    My previous fridge, a vintage 1998 Maytag, gave similar results with slightly wider temperature ranges.

    Air temps? Might be 48°F to 50°F. Wall temps? Same thing, sometimes higher.

    The take-away? Don't worry about air temps or wall temps. Absolutely focus on the internal temps of food.

  • 11 years ago

    Measure the freezer side and report back.

    The air exchange shutter between the fridge and freezer may be stuck. Or the fan is not working properly. Would be nice to know where it is sensing that 34*.


  • 11 years ago

    Apparently, we aren't turning out enough appliance repairmen. The soonest I can get one is Thursday. I've got a call in to another one who is a friend of a friend, hoping he might be able to get to me sooner. A friend who owns an appliance store told me that if he called his guy, it would probably be next week before his guy could get to me.

    Re sniff test: I just poured out a half gallon of milk that didn't pass the sniff test. I do not store milk on the door. It is on the top shelf of the refrigerator.

    DH has a coconut cake in the fridge. My Thermapen registered 56 when inserted into the cake. He ate it anyway. :-( He is much more casual about food safety than I am.

    I have checked the freezer side to make sure the shutter (thanks, weedmeister, I didn't know the name) isn't blocked. It wasn't.

    DH just bought a thermometer. Unfortunately we live in the boonies and the only fridge thermometer available was a dial type. It is in the fridge now. When I finish there, I'll test the freezer. So far, I've "tested" the freezer by making sure everything feels solidly frozen.

    NOTE: The thermometer has been on the middle of the middle shelf for an hour. It is reading above 40 degrees, about 42-43. I have also put a glass of water with a not-so-instant thermometer in it. I'll check it in 30 minutes or so and post the results.

    We have no pets and very little dust. I cannot move the fridge to check the back. I think it has wheel locks and I cannot see where they are. My recollection of watching the installaltion is that there are no coils on the back. I've looked at the grill at the bottom of the front and it shows no evidence of dust build-up. I have checked the manual and there is no mention of cleaning coils.

    There is no problem with the lights. I've checked that and they are going off. Plus, they are LED, so I can't imagine they would give off enough heat to cause a problem.

    jwvideo, if I were to do an old-fashioned defrost, would there be water on the floor? I have wood flooring in the kitchen. I don't want to add to my problems!

    Just to make matters worse, in all of this but after I tested the coconut cake, I've somehow messed up my Thermapen. I am now reduced to using an alternate not-quite-so-instant read thermometer. I think I laid my Thermapen down in a puddle of water on the counter. I use my Thermapen all the time. If it is dead, I'll be lost. Fortunately, my birthday is soon. A new one will be at the top of my list.


  • 11 years ago

    Oh, no! I hope the Thermapen didn't take one for the team!

    You seem to be holding up really well despite the circumstances, so good on you!

    Let us know what happens.

  • 11 years ago

    My GE Arctica has a "jelly-roll" condensor coil behind a panel on the rear. Your unit has the same per the parts diagram. Looks to be the same dual-evaporator system design. Seems unlikely it'd accumulate enough debris in 15 months to have an adverse effect. My unit is 10+ years old. The system board went bad 5 years ago. I cleaned the condensor at that point when back there. Probably should check it again.

  • 11 years ago

    Is it possible for a refrigerator to heal itself? The fridge thermometer is showing slightly below 40 degrees. The sorta-instant-read thermometer sitting in the glass of water is showing 38 degrees. Nevertheless, the milk went bad, the sausage spoiled, and the coconut cake was 56 degrees. What gives?!?!?!

    I've thrown out all the things that would have gone bad if the temperature had been above 40 for any length of time - except DH is clinging to his coconut cake. That's fine, but I'm not eating any of it!

  • 11 years ago

    Overnight update: The gauge thermometer reads 39 degrees. The thermometer in the glass of water reads 39 degrees. The display on the door says it is 33 degrees. The manufacturer recommends setting the temp at 37. Do I just need to set the temp as if the display is always 6 degrees off? Do I need to run it down to 31 so that it is actually 37 in the refrigerator?

  • 11 years ago

    cake in the fridge? What for?


  • 11 years ago

    Not unusual the temp varies. I set mine at 35°F. Earlier this morn it was reading 35°F on the display. A remote thermistor-type thermometer on my volt-ohm meter read 35°F at the middle shelf. I moved the sensor to the next shelf down, left it a while. Now the panel display is 36°F and the thermometer/sensor is 38°F after the door was open briefly. A few mins later reading 36°F.


  • 11 years ago

    weedmeister, we always keep coconut cakes in the fridge. What for? Because my momma said so. :-)

  • 11 years ago

    It's entirely possible you have a problem somewhat similar to the problem I had with my Jenn-air fridge. It would get wild swings in the freezer compartment, sometimes instead of 0F in the freezer, (as it should be), it would swing as high as +20F. then for days, I might not see the problem again, (it would stay close to 0F). Fortunately as I have a single compressor/single evaporator fridge, even when the Freezer temp swung up to +20F the fridge would still stay at 37F, as it uses air from the freezer to keep the fridge cool.

    But if yours is either a double compressor or even a double Evaporator fridge, then any problem with the cooling system on the fridge or freezer side could cause the fridge side to heat up intermittently.

    The problem with mine turned out to be a partial plug (a little piece of copper) in the sealed system. The appliance guy cleaned it out, showed me the piece of copper, recharged the system, and the fridge and freezer have been spot on temp wise, ever since. (about 2 years now).

    So You need to monitor the temp and see if it ever climbs, and then hopefully find service as honest and knowledgeable as I did! (It cost me a lil over $300 to have it fixed.)

    Gary