Software
Houzz Logo Print
luluatdp

How long do I run my new pool pump?

11 years ago

Hi, we just installed a variable speed Pentair Intelliflo, mostly to lower bills and get that California rebate. However neither the installer nor my regular pool guy seem to be able to tell me how long I should be running the pump and at what speed. Our in-ground pool is about 15000 gallons and has a chlorine system.

Keep in mind that California Dept of Water and Power has the following requirements in order to rebate us the price of the pump.... Thanks in advance for any help!!!!

  • Pool pump must be programmed to:
    • Run only during 8:00 p.m. to 9:59 a.m. (off-peak electric demand hours)
    • Run
      for the minimum time necessary to maintain the water in the condition
      required by applicable public health standards and comply with
      California Energy Code calibration, low-speed default, and maximum flow
      rate requirements

Comments (4)

  • 11 years ago

    Pentair's Customer Service at 1.800.831.7133 might be able to advise you, but I'd probably start with programming it to run at low flow from 9 PM to 9 AM and manually running it at high flow an hour or so before getting in.

    How do you plan to maintain Chlorine and PH levels?

  • 11 years ago

    There are quite a few different Intelliflo pumps. Do you have one of the ones with just 4 different speeds or one of the more sophisticated ones where you can choose all the settings for various functions? The one I have will run a series of tests for current draw and water flow and figure out how efficient it is.

    My pool is very old with plumbing that is considered too small by today's standards so the most efficient was at the lower speeds. It turned out to be 18 GPM through the skimmer and the lower the better with the pool cleaner attached. It won't go lower than 15GPM so that is what I run with the pool cleaner and run it 8pm to 6am in summer. It is VERY quiet. My pool is 40,000gal. I've had it for 6-8 years so don't remember what single speed pump I had before but I think 2HP. My summer electric bill dropped $80 with the new pump because it kept me out of tier 5 pricing.

    I end up setting another mode for 30GPM for the skimmer for quick clean up if leaves blow in. I don't program that just turn it on when necessary. Probably would hardly ever be necessary if the morons that designed it had put the skimmer downwind instead of upwind!

  • PRO
    11 years ago

    It all depends on the size of the plumbing. Plumbing requirements dictate the size and speed of the pump. Just because you have 2" lines does not mean you need a 2 hp pump.

  • 11 years ago

    A starting point would be to shoot for turning the water over twice a day. If you can maintain good water quality with a two-a-day schedule, you can lessen the turnover, eventually you'll hit a sweet spot where you're maintaining good water quality without running your pump too much.

    I'd recommend planning on a 12-hour run to start with. Out of the 12 hours, have the pump run on high for two hours and at a lower RPM for the other ten hours. The two hours at higher speed helps the skimmer, or that time can be used to run a pool cleaner. If debris isn't a problem, you can run on just the lower RPM three days in a row and on every fourth day throw in two hours at a higher RPM.

    You'll eventually customize your pumps run times and RPM setting to suit your water quality.

    Two turnovers is 2 x 15000, or 30000 gallons per day. You'll need to get into your pump's manual to get estimated GPM flows, or if the pump display shows GPM flow, you can use that. GPM is also limited by your pool's pipe size. Typically 2". It's also limited by how many GPM your filter can handle.

    When you have that info, just run some numbers. If you run for two hours at a high setting, say 70GPM, 70GPM x 60minutes x 2 hours = 8400 gallons in two hours.

    30000 gal - 8400 gal = 21600 gal.

    21600 gal / 10 hours / 60 minutes = 36GPM for the other ten hours.

    A starting point for you.