Software
Houzz Logo Print
jpmom

Help with Chimney Style hood

10 years ago

We are reno-ing our kitchen. Currently have the micro over the cooktop. Plan is to pull upper cabinets out and install a stainless chimney hood. It's on an outside wall and will require a rear vent. It will be 36"


From an aesthetic standpoint, we want to tile this wall - and have the hood mounted to the wall - with a 24" wide chimney going up to the ceiling.

We need the hood to be 36" from the counter top.


We looked at a Proline --

http://www.prolinerangehoods.com/index.php?main_page=product_info&cPath=30_36&products_id=236


This would work - but we would have to cut the chimney to fit the space (18" of chimney - they sell in 12 and 24 lengths) The hood itself is 18" high.

Cost for this would be $2300


Didn't really want to spend this - and also, it has a 1700 CMF blower - do I need this much?


Saw a thermador for $1700 - But I'm not sure about the size of the chimney. I can't have the hood itself be less than 36" from the cooktop.

http://www.abt.com/product/38745/Thermador-HMCB36FS.html

Comments (11)

  • 10 years ago

    I'm not going to comment on blower or brand, but we had the same issue with the chimney length (our hood vents through ceiling and then up through the attic to the roof). Rather than pay for an expensive custom length, our duct cover extends into the attic. I cut a piece of plywood to seal off the area at the top of the cover, including the hole that the duct passes through. Then I foil taped and foamed everywhere I could to seal between the conditioned and unconditioned space. I believe the cover at the ceiling cut is caulked for a clean look.

    For what it's worth, I also installed a support board to the wall (screwed into studs) before tiling. This lets the hood sit more or less flush against the tile backsplash.

    jpmom thanked thull
  • 10 years ago

    Joe -

    We are installing a Thermador 36" gas cooktop:

    http://www.abt.com/product/36459/Thermador-SGSX365FS.html


    We have 9-foot ceilings.

    As I said, I need the hood to be 36" from countertop.

    I cook a lot - and do enjoy sautéing - but I don't deep fry anything. I will sear meat on high heat - which creates quite a bit of smoke.


    Rear vent is needed on the blower - the chimney is merely aesthetic.

  • 10 years ago

    I also need to know about venting outside - In the case that there is a stud behind where the opening for the blower - how is this handled?

  • 10 years ago
    last modified: 10 years ago

    As you see on their web page, the chimney is at least 24" wide. The duct is 10". This allows you to offset the duct a bit to avoid the stud by using an adjustable elbow duct.

    jpmom thanked eshmh
  • 10 years ago

    With the Proline, the chimney is purely decorative. The blower is located on the back of the unit (they actually rotate it to the back as an option)


  • 10 years ago

    Can anyone help with this?

  • 10 years ago

    If you have a stud in the way of a thru-wall duct, it may be necessary to tear out some sheetrock so that the stud can be cut and the area framed out (like a mini window space) to carry the cut stud's load around the cutout. In this case, as only one stud would be cut, the header, bottom plate, and added load-carrying trimmer studs would be minimal.

    See illustration at: https://en.wikipedia.org/wiki/Wall_stud

    jpmom thanked kaseki
  • PRO
    10 years ago

    Kas is right about the ducting. Even hoods with the duct turning in the flue would probably need a cut wall stud. Generally isn't enough space to make it work within the flue itself.

    There is a faber very similar to the proline that will work well. And they make an adjustable flue so itll make your life easier.

    Maestrale

    Should be around $1500 with the flue roughly and its a solid hood. It's 600CFM but really that is about all you need for the cooktop in question

    If you want a little more streamlined, I like the Zephyr Venezia

    Venezia

    That should be more like $1300 all in with a 715CFM blower

    jpmom thanked Joe Henderson
  • 10 years ago

    Very good info. And thank you for the hood reco's.

  • 10 years ago
    last modified: 10 years ago

    It depends on the spacing of the studs. If studs spaces at 16 inch like in Canada, I don't see that the stud has to be cut.

Sponsored
Miller Woodworks
Average rating: 5 out of 5 stars23 Reviews
Franklin County's Trusted Custom Cabinetry Solutions