Software
Houzz Logo Print
jason_jennings49

Cloning Blueberries using an Aeroponic System - Help Needed

10 years ago

Hello All,


I built a simple aeroponic system to clone things like blueberries, mint, basil, ect. I took green cuttings from my neighbors bushes that produce very well. I cut the stems at a 45 degree angle and dipped them in clonex gel and let them sit a few minutes. I put them in 3" net pots using cloning collars. I didn't use a rapid rooter or anything like that in the pot as I think the collar is all I need.

I then put them into the system and let them go. I didnt do anything to the water. I just used tap water. Should I be adding maxigrow or any type of rooting enhancer? There is no need for an oxygen stone in the water correct? Is my process sound or is there anything else I need to do to get these ti propagate properly?




Comments (13)

  • 10 years ago

    Update and a bump. Some of the cuttings are starting to dry up. The leaves are getting brittle. I do not see any roots forming. Any suggestions?

  • 10 years ago

    tap water might be an issue depending on whats in it. Try some distilled water.

    Jason thanked adamg_55
  • 10 years ago
    last modified: 10 years ago

    If they are outside protect them from strong light, high temps, direct sun and wind. These will all increase demand for water and the cuttings wont keep pace as they dont have any roots :) Cuttings dont need much light, a small compact florescent is plenty. A humidity dome will help maintain a good RH% and shelter the cuttings from drying winds, occassional misting of the leaves can help. Cloning indoors is generally easier as the environment is more stable, no day/night temp swings, wind, sun etc to deal with.

    Jason thanked hex2006
  • 10 years ago

    @hex2006 Thanks for the feedback. I cannot find a humidity dome that will fit this large storage tote that I used to create the cloner. Can I dome each individual clone with a plastic bottle?

    I can move them inside. I original was going to put them there, but put it on the deck in the sun. The garage is rather hot at the moment so I am worried about the water temperature.

    I also read I should take off all the leaves as them take water away from the stem to create roots. Any idea on how accurate that is?

    I also made the mistake of not sterilizing the scissors I used when making cuts. I think I am going to start over this weekend.

  • 10 years ago

    If you trim the leaves you can cut off half the leaf, but leave the other half, hard to explain but look at the marijuana forums and there is a ton of info on cloning

  • 7 years ago

    It is a difficult process. The pH is critical you want to have your water at about 5.5.

    Supposedly the easiest plant to clone is bluecrop.

    Test results are obtained with soft cuttings in the spring. I have used various routes hormones. Now I'm using a dip and glow and after dipping the cuttings I add the remainder to the tank

    Temperature should be from 70 to 72 degrees.

    They say not to add nutrients before root development but I do and look for a formula with B1.

    I set the timer to run for 50 minutes and then 10 minutes rest.

    I don't use a dome but I do use fluorescent grow lights and have them on mildly for 18 hours a day.

    Even with all that the results are disappointing and I think you might be better served to dip in a powder root hormone and plant immediately into a SaSand peat , if you stumble on a winning formula please get back to me

  • 7 years ago

    I've tried various controls and supplements. Also varied the pH. As far as I'm concerned the cloning machine doesn't work and you're better off directly with a rooting hormone and softwoods into a peati mix.

  • 6 years ago

    Hey guys, i highly recommend you this book if you want to see immediate results in your garden. go check it out it is available for only $0.99. https://www.amazon.com/Hydroponic-Gardening-Tips-Tricks-hydroponics-ebook/dp/B084LHPNW

  • 6 years ago

    Laurinda, that link does not work.

    Jason, how is your Aeroponics system doing?

  • 5 years ago

    I do this with citrus and have 90% success rate. Angle cut at bottom doesn't matter. You need to remove small sections of the bark and leave the phloem showing. This is where roots will form. No hormones are needed. However you need to use RO water, not tap or distilled. I run 24/7 and takes about 5 weeks for roots. 5 days for tomatoes and vegetables. I'll cut some blueberries and try to see if any success.


    Make sure to trim leaves and only have about 3-4 leaflets.


    Mist leaves with an Epson salt solution almost daily depending on light source and temperature


    Water needs to be between 70-75 degrees


    Do not to outdoor unless you can control the environment like a greenhouse.


    Might be easier to just do an air layer graft. I've been very successful with figs, mulberry and citrus.

  • 4 years ago

    Brian High did you ever achieve any success with blueberry stems in the aeroponic system? I am really interested in pursuing fruit cultivation through aeroponics, but I have found almost nothing when it comes to info on berry bushes.

  • 3 years ago

    Great article https://opomax.com.pl/

Sponsored