Software
Houzz Logo Print
scott_ruport

Plywood over plaster?

9 years ago

I want to install wood on my ceilings in my dinning room and living room. I have plaster ceilings. Do I fir under the joices with wood strips through the plaster, or should I screw plywood to the joices?

Comments (12)

  • 9 years ago

    I don't think laths would help so I would screw plywood to joists.

  • PRO
    9 years ago

    I want to install wood on my ceilings in my dinning room and living room.

    Might I ask why??

  • PRO
    9 years ago
    last modified: 9 years ago

    Depending on the type of wood and weight. I just installed a rustic cedar ceiling, it covered a 2Hr Double layer firecode drywall lid @(1-1/4" thick) that I couldnt remove. I used 1/2" Plywood strips and glue + fasten them thru the drywall into rafter ties. And then glue/nailed the cedar to the Plywood furring. This was a very thin lightweight cedar and I would be concerned about weight overall with material choices. A properly installed lath/plaster ceiling is already A heavy hung load and when it snows here that roof can see a Lot of Load.-best

    If she is reading I must say the cedar was My clients Idea...

  • PRO
    9 years ago

    "Do I fir under the joices with wood strips through the plaster, or should I screw plywood to the joists?"


    Depending on your ceiling framing, your choice of wood thickness, and the joist direction, you may not need to do either. Simply locate the ceiling joists and snap a chalk line on the plaster ceiling to indicate where to nail.

  • 9 years ago

    The reason why, is my ceiling is ugly, uneven, half textured, and wood looks good. I had some water damage in the past and I want to cover it. My ceiling joist run perpendicular to my wood floor and I want the ceiling to match. I need to cover the plaster. It is a 2 story house built in 1920 so it's my upstairs floor joists.

  • 9 years ago
    last modified: 9 years ago

    My question wasn't very good, I want to install planks.i didn't know if I could just install them like Joseph said or if I should cover with plywood and nail to the plywood.

  • 9 years ago

    To wind up with a level ceiling you will need to shim and lath,plywood will eventually conform to contour of old ceiling.

  • PRO
    9 years ago
    last modified: 9 years ago

    As Klem points out you need to shim level with furring FIRST and its easier said than done as you need to start with the LOWest point of youre ceiling and continue that until in plane.

    If you intend A Tongue and groove of any thickness it will not bend to youre out of plane ceiling. Not that you care but, In the picture above I used 1/2" ply strips cut to 6" widths and they all got leveled in the process as they were spaced 20" apart in such a way that the individual 8' lengths had support under every lap/butt joint.

  • 9 years ago

    "and its easier said than done "

    Indeed it is and u-tube can't cover all the bases.

  • 9 years ago

    check out
    antiqueceilings1845 on Ebay. They have a lot of different designs and may be an easier solution for you.

  • 9 years ago
    last modified: 9 years ago

    Just fix the plaster. You will have to do enough work to get all of the support level that you might as well add value to the home by sticking with it's historical precedent rather than putting it in the latest belly shirt and miniskirt. A wood ceiling is in no way appropriate to a grandma of it's age. It ain't MCM.

Sponsored
J.Holderby - Renovations
Average rating: 5 out of 5 stars4 Reviews
Franklin County's Leading General Contractors - 2X Best of Houzz!