Software
Houzz Logo Print
mikefen

LAUNDRY ROOM TILE

9 years ago

i tiled my laundry room and really messed up. im so embarrassed to say that i started from the right and went in a circle....i have no idea what i was thinking. should have started from the back and worked in rows to finish . well that said i have uneven grout lines and some tiles are not level with others. debating on just tearing it out and starting over.....looking for opinions....





Comments (23)

  • 9 years ago

    And you have lippage because you used a 50% offset pattern, which is incorrect. No more than 1/3 offset with large format tile. I'll bet you used thinset as well, right?

    This is a rip it out and redo or forever stub your toe and trip.

  • 9 years ago

    i used kerabond thin set. they gave me that at the store. have not grouted yet but i dont seem to be able to feel it too bad walking over it...dont think think ill stub my toe.....can i use a grinder to open up some of the thinner grout lines?

  • 9 years ago

    No, you can not use a grinder unless you want to chip it to heck and back. Go ahead and grout it and live with it if you can live with it as is for now, as long as you know it will have to be ripped out and redone properly before you ever sell that house. Or, rip it out and hire an actual tile mechanic and get it over with now.

  • PRO
    9 years ago

    When I worked at a remodeling company, my guys would always start in the center and work out from there.

  • 9 years ago

    i could rent a machine and sand the lippage and polish it...then i would save ripping it out....maybe?

  • PRO
    9 years ago

    A lot of the problem is that when you use larger tiles, you need to "float" it over whatever the stuff is called that the tile is set in. It needs to be thicker so they can be leveled. Also, usually larger tiles (I'm assuming yours are 12x24) usually have larger grout lines as well.

  • PRO
    9 years ago

    Btw - tile is one of those areas in remodeling where if it's not done right can ruin the whole project.

  • 9 years ago

    i agree.....im going to rip it out. i found one tile that came loose already. if not thinset what is correct for travertine tile?

  • 9 years ago

    the tiles are popping out really easy....which is another concern. i did another job in a bathroom an i had to take one tile out and it was really hard to get it out. these are just popping right out.....yikes!!!

  • 9 years ago

    just want to thank kristen and sophie for pushing me to redo this....i got all the tile out and cleaned up. the store felt bad and gave me a break on new tile. we have a ton of rain coming to LA this week so ill have to wait to install....ill keep you posted on the job and post pics....thank you!

  • 9 years ago

  • 9 years ago

    great decision!! keep us posted

  • PRO
    9 years ago

    Best wishes! As I've learned - there are always bumps on every project!

  • 9 years ago

    Glad they gave you a break. Some tips/suggestions for the next round:

    1) use tile spacers

    2) make sure you are loading your mortar correctly on floor and back

    3) start at the center of the room. (We used chalk lines to this for everything we've laid in our house to do this. )

    4) check leveling as you complete it (small sections).



  • 9 years ago

    While you're waiting for the rain to end, why not take the time to watch some how-to videos? The visuals might help you on your next go around. Good luck!

  • 9 years ago

    hey hateshop......ive done a whole bathroom walls floor shower, it all came out great.....i think it was really doing the offset tiles and starting from the wrong place....halfway in i was in deep trouble.....anyways im using the self level wedges, starting from the back wall.....taking a deep breath...hahaha and it will come out great..... ill use a little more thin set for sure.....ill keep you posted on the outcome.

  • 9 years ago

    I'm sure it'll work out fine, this time. Looking forward to seeing the results.

  • 9 years ago
    last modified: 9 years ago

    Sophie isn't exactly correct... the 1/3 bond pattern is recommended for very large ceramic tile not well cut and gauged natural stone, which is installed in a 50% running bond pattern all the time... even in larger format sizes. Do use a large format tile mortar, but remember to use white with your travertine.

    I'm not questioning that you are having problems, you should have nice straight grout lines and your tiles definitely should not pop up. Your tiles may not be gauged perfectly but it's impossible to tell from your photos and are the less likely culprit. The problem could also be your floor - is it perfectly flat (not level - but flat - no dips or bumps)? What did you put down underneath the tile? Natural stone really needs a floor that isn't flexible to avoid cracking. Did you use the proper trowel to get really good coverage with your thinset? 1/2 x 1/2 x 1/2 square notch what you should be looking for.

  • PRO
    9 years ago

    Offset is only any issue with larger tiles such as a 36x8?, there should be no issue with these tiles if leveled properly. Not too many people would consider a 12x24 tile large format today. The issue has become prevalent with wood look tile that are sold in long thin shapes creating bows in the middle of the tiles. People hear key words and just keep repeating them.

    In your pics you are not showing slippage due to bowed large format tile but rather improper leveling.

    Go to HD and buy a leveling system. The cheaper spacer/wedge set up works perfect especially for one time small area. The spacers set your grout lines and the wedge will level your tiles.

    First lay a level on your sub floor and detect and level issues as if subfloor is not level you will have issues.

    The reason your tiles popped right out is due to lack of coverage. Make sure when you lay down your thinset you use flat side of trowel to force it into the substrate then comb it out. Also back butter each tile. This is simply using the flat side to apply a very thin layer of thinset to the back of the tile. It is tedious but will help with leveling and getting full coverage of thinset.

    Lastly make sure your thinset is not mixed too dry and you stir it as you go. If you take to long throw it out and mix another batch. Do not use the whole bag at once.

    Use a sponge to clean out grout lines as otherwise you can have color issues with grout. Do your layout and cuts first this way you concentrate on the laying only.


    Good luck

  • 9 years ago

    wannabath your totally right. there was not enough thinset. i did back butter but there still was just not enough...im going to use the wedge system for sure and ill use spacers to insure things dont move around. ill go for a 1/8" space.

    my wife is an architect and she agreed that the half offset for these tiles are just fine......ill stay with that as thats the look we want.

    i got everything cleaned up today and im ready to put down the ditra....yahoo!

    fyi: the thinset came up easy, i put down hot wet towels for about 2 hours and simply peeled it all off with a spider chisel on a sawsall..really fast and no effort. followed with a quick belt sand......im good with this.....

    on a side note this is all permitted and i framed the partition, plumbing, gas line, vents, electrical and drywall....all passed inspection first round......its going to look great!

  • 9 years ago

    got my ditra all in....! looks wavy haha but its flat and level.....

  • 9 years ago
    last modified: 9 years ago

    well i got it all in with grout. im really happy with this. its not totally perfect but much of the left and right sides are going to be closets, washer/dryer stacked, basin an upper cabinets.......first time working with tavertine stone....not as reliable and consistent as porcelain but thats stone i guess....there was actual uneven thickness and some warping in these stones...not sure if thats normal or just poor quality in the stone...this is my first time working with it and my second time ever doing tile......that said. i love it and thats what matters along with a big hug from my wife....haha...cheers everyone...