Software
Houzz Logo Print
champion6sigma

Reel Mower maintenance - sharpening - backlapping - etc.

9 years ago

I have noticed that on my push reel mower, the sharpening (backlapping) I do has not retained its ability to cut paper. I'm a novice at backlapping, I've only done it a few times, I initially was under the impression that though crudely done, I was successful. I'm unsure if I'm not properly making adjustments because I have noticed in the paper test that I'm losing ability to cut paper within 2 weeks(perhaps sooner if I had checked sooner).


Can anyone tell me if that sounds normal? My grass was being kept at slightly below 1/2 inch then it went to 1/2 inch....not that the actual grass cutting should be dulling steel too quickly....I'm giving the HOC since there is a greater chance of hitting earth, and other debris much more often that low then if I was at 2 inches or higher. Mowing has been done every few days for the most part. I do have quite a bit of sand dormant in some areas which occasionally gets to the blade. I do need to adjust and level on the sides of our home more and fix some of the higher spots that didn't get leveled correctly.


I'm wondering if the reel to bed knife distance is actually incorrect and there is too much metal contact. After backlapping...multiple passes with the compound and hearing the change in sound similar to a bike with playing cards in the spokes....I figured I had everything OK after getting the sound and cleaning the blades and being able to cut paper nicely. There is a definitive feel of the reel along bedknife as it turns and it does not spin freely and easily. Nothing at all like a fidget spinner! lol

Is reel to bed knife the usual culprit to premature dulling....or is user error being reckless with the mowing and scalping earth, plowing through unseen branches, rocks, debris, occasional sand to blade a bigger concern....or is 2 weeks or so of sharpness usual?


Any tips on how easy a reel should spin? Tips on the backlapping process. Tips on frequency. A preferred compound to use? I'm currently finishing up with the compound that came in a kit.


I've done the backlapping twice in the last 1.5 months and before I do it again...which is physically tough for me...I would appreciate any advice that can be given. I've watched youtube videos....read what I could find from googling. It would appear the data I've found, many of the posters seem to be beginners themselves.....


Also, how do you all clean your reel mowers or rotary mowers? Is using a power washer acceptable? I always struggle to clean after using the backlapping compound. Do you all spray down with water hose or power washer and then hand dry?

Any additional reel mower care tips?


Thank you.



Comments (67)

  • 9 years ago
    last modified: 9 years ago

    I can keep it at a lower level until around this time of year. The problem I have when raising it is the lawn mower is so light, it's not heavy enough to put weight on the wheels so it turns consistently.

    I read the pdf. Good info. It talked about appearance after the cut or something. I was seeing that the very tip of my grass was turning brown a day or two after I cut it. Adjusting the bed knife so it would cut paper helped.

    Champ, I see on your other thread you have a McLane push mower. I am thinking about getting one to replace my great states. What are your thoughts on the 2 mowers?

  • 9 years ago

    The Mclanes greensmower I have is a beast and amazing. I had started to write more but I'll add on when I get to a cpu and give my BlackBerry keyboard a rest.

  • 9 years ago

    Thanks. There is one on craigslist in my area and includes the grass catcher. I am wanting yo upgrade my great states. My backyard has an incline so I would also like to know if I would be able to push it up an incline.

  • 9 years ago
    last modified: 9 years ago

    OK. Just had 2 hours of fun trying to raise the HOC on the greensmower. The manual is ridiculous. I could not get the wheel sprocket off without exreme effort. I now am cutting at about 1 inch, the highest the greensmower is capable of...what the manual does not state is that the small guide within the wheel chain area needs to be lowered as well, furthermore mine was already at the HIGHEST hole level , my wheels were in the CENTER hole bracket height , manufacturer ERROR. So I spent a long time fixing the center bracket which bolts not reachable within reel area by hand, and moved it down a notch so that I thought it could match the one hole drop in the wheels i did, after killing myself putting it back on i then realized the error and went down to the last set of holes to match the wheel bracket selection of the last set of holes now the cover of the chain and the chain sits and rests the way it should be. I was mowing from day one with my new mower with the socket rubbing against an internal bracket. Once taut it doesn't rub but when starting it can and did. Glad that is fixed now. So to recap, the wheel area rear bracket has 3 levels. 1, 2, 3 with 3 being used to get the higest HOC. The internal bracket thing within the chain cover has 3 sets of notches 1,2,3 and my bracket is held in on the 3 level.

    The front roller has a sliding mechanism which I know now is FINE adjustments. Loosen screws and it slides up and down, not a great way to be perfectly accurate :( but its so minor that eyeballing maybe is just fine. What i initially thought is that because THAT slide is about an inch of available movemement, I figured that the 3/16 to one inch possible HOC of the greensmower is controlled STRICTLY by the front roller slide! Wrong. Thats how I shaved my whole yard earlier this week. After reading the manual more closely I read the wheel adjustment part to find out it holds additional height adjustment capabilities and they are the MOST important of the two. I was going to try and sharpen while everything was OFF but its too late, daughter is sleeping, and I'm in a lot of pain. I was able to add some oil, grease up moving areas, clean it up a little, and test out the mower.

    Sherm is the craigslist one a greens or the wheeled version? Send a link, actually if you don't mind.

    Now to my review - hopefully that didn't bore you...

    I really like mclane equipment. When I decided to upgrade from my great states specialty I went with the best one I could find. The greensmower was a big investment, it is very expensive but I very much believe it is the BEST push mower non powered in the world. Luckily there is no tax or shipping fees.

    The unit is the heaviest push mower human powered that I know of. I'm pretty sure I researched every possible make and model.

    10 blade's on it are amazing. The handle bar seems a bit of an odd angle or length but I'm thinking it was designed in that way to help negate the weight of the mower and make it easier to push. It does move up and down slightly unless I just need to tighten the screws more. Not sure. The grass catcher is NOT the greatest design because of the angle it sits on mower. The size is great and can hold a lot but you will NEVER fill it while pushing because only the bottom portion can hold grass before it slides back into the cutting area! The powered reel mower that REELJAKE has given me has a GREAT catcher on it and it sits perfectly at a better level. My first cut with it I caught all the grass it mowed. When I switched to the greensmower to try and get a perfect inch I kept emptying the greensmower catcher into the larger one every few passes because it simply wont hold a lot of grass. That being said I don't believe its meant to - WHY? because a green is supposed to be kept short and supposed to be simply cutting the top of the ends of the blades and pretty much not have much of any clippings. This truly is how I usually cut when I'm going at it every 2/3 days. I barely cut anything, and for that the catcher should work fine. I hadn't cut in a long long time and so thats why I had so much grass clippings this week. I almost filled a contractor bag. Its something to consider if you plan to not cut often and want to use the catcher. I actually NEVER have used the catcher ever until this week after using the powered reel. I've decided to catch my clippings from now on to preven thatch or whatever. My yard has never been the height it was at this week. Not since maybe we bought it.

    As far as maneuverability its not hard to go up hill. I usually go up hill on my side of house with an incline. I also walk sideways across the plane. The sprocket and wheels are what push the reel blades and to me it does a great job. However, if the grass is high and you are cutting a good part of it, it will be more difficult to get 10 blades to cut it. There won't be bouncing like the great states but it can get bogged down if your trying to cut too much or if you don't have momentum. If I get bogged down I simply back up and remow what i've already cut and get momentum going and then cut over the new area with HALF the reel rather than doing a full pass across all high grass. In that sense its essential to follow the 1/3 rule if only for the fact that its harder to cut grass the more blades you have. On the powered reel side ijakes mower cut through my yard like butter. LOL. And its because of the engine....t a powered reel is simply easier to mow with than a push, Even though the powered reel weights 3 times the weight probably. I can no way lift it by myself.

    I lift the push mclane every use so that I can place it the area it stays in at night. I'm in my thirty's. I'm not that strong not as strong as I once was. The great states is easier than the mclane to push, but the mclane is still very easy. Both are difficult to use if you are going through thick grass and don't have momentum. The greens mower is easy to maneuver, and you can cut very close to edges on the right side which doesn't have the chain cover. I think the wheeled version is ez to change height. Not sure.

    There is a distinct quality and blade thickness difference when comparing the mclane to the great states. Everything is heavy duty. I don't think there is any way you can be unhappy with the mclane push, especially if its the greens mower with the roller and 10 blades, and as long as it wasn't abused.

    When I first got mine I babied it, I spent more time inspecting the grass for artifacts then time I spent mowing. Now I'm a little more liberal but I still do a good job looking for rocks, debris, etc. My worst thing I've hit is a penny. Could not see the thing but it jammed my mower good. Other thing was PAPER! It jammed reel very good and I couldn't budge it....then I wet it after using my brain and less brauns. Then it tore up after that.

    I just got some new information from turflife on backlapping, as well as with the new links I found, I'm now very confident that I'll be able to set my mclane perfectly and sharpen very well. In fact, it spins and cuts great right now....its my great states that doesn't spin as well, but thats going to corrected soon.

    Hope that helps.

  • 9 years ago

    My incline is probably 40 degrees. Its steep. I really should have a fence guarding the sidewalk. If I was rich I would maybe put down ground cover, to replace the inclined area, ground cover like dchall had suggested to me for various areas of the yard that are not sunny or under trees or difficult to grow areas.


    You should have zero issues with it. If you are able to use the great states you should be fine with the mclane. Just expect it to be easy, but not as easy as the great states. Great states or mclane, I always get a workout, I always sweat hard, it always take effort...I would think of it as the difference between pushing a grocery cart that has 15 pounds of food in it, to pushing a grocery cart that has maybe 25 pound of food. Hope thats a good analogy. I cant find weight of the mclane. The specialty is twenty something and might be discontinued one website I found said.

    I have a replaced right hip. I have spinal fusion, part of my rib removed and fused into spine to supplement two crushed vertebrae that were removed and a cage was inserted around my spine. I just had a CT last week showing my lumbar level has all 5 levels with a disc bulge and every level showing arthritis and one level having an additional problem. I have rheumtoid arthritis in most the joints in my body. Avascular necrosis beginning in my left hip. The funny thing is that those issues are not even the reason I'm labeled disabled.

    So far I'm using the push mowers just fine. The mclane is harder, much harder to lift vertically, for me. I have to pick it up from the base area carefully because its wider and just move it to where it was pictured in other thread, basically just lift it up a step. the great states I can lift by handle and carry it across the yard by the handle if I wanted to. No way I could do that with mclane. The powered reel I was very happy jake and my inlaw helped get it in truck. I push myself hard to do physical things and stay active, but I know lifting anything with extreme weight is dangerous for me, if I lift it wrong or if its too heavy. Now that I think about it. My basic push husquevarna rotary mower is HARDER to push than the mclane. The mclane might be similar in weight to a light weight rotary engine. A small light weight rotarty..... my husquevarna is definately heavier than it and more work to push.

  • 9 years ago

    Thanks champ. Would you consider the McLane to be a big upgrade over the great States?

  • 9 years ago

    I wonder if the push with 4 wheels rather than a roller is easier to push...the greensmower has a roller with vertical blades which are supposed to help groom the grass and maybe lift them....something like that. It may actually embed within the earth just slightly thus making it a TINY bit harder...but I may be wrong. I suppose I'm just thinking it would be easier to move something with 4 large wheels rather than two wheels and a roller with metal rings. Less friction? or something. The roller which my dad found on sale for the powered reel is a flat roller and is designed to produce striping, avoid scalping and push the blades of grass in one direction. The roller on the push greens mclane doesn't really do that. mclane greens does not product striping effect but you will see lines through grass from the roller thing it has. striping or not, there really isn't any worry of scalping the yard when you use any type of roller. That is the great thing about using a rollered reel. A level HOC compared to rotary, and hardly any way to scalp the earth. The level HOC is transparent for those with lots of uneven areas of yard. If the yard is fairly level a rotary HOC is not bad. My neighbor attempted to level with me but didn't use as much sand...now uses a rotary and the grass looks like a roller coaster.


  • 9 years ago

    yes its a big upgrade. You will not have bouncing anymore and you do NOT have to run or go fast with the mclane reel, the chain will give you the speed required at a walking speed. I honestly don't know the weight or spec differences between the 10 blade greens and the other push but regardless it will be a big upgrade, with the push greens being the biggest possible upgrade you can get without going to an engine.

  • 9 years ago

    Last couple of questions champ......

    What about adjusting the height, backlapping, and adjusting the reel to bed knife? Could you elaborate on the ease of all of these and how often you have to do it?

  • 9 years ago

    Adjusting the height requires loosing bolts or removing bolts, the wheeled version is probably different and maybe easier. backlapping to my knowledge requires the kit unless you rig something up with a drill or other, I don't know if it can be "walked" in reverse, I don't believe so. Adjusting reel to bedknife is dealing with multiple bolts and to me simpler than great states screw method. What I'll be doing is using a sheet of paper to keep between blades and bed and then I'll tighten down on that , and then once that is established, I'll remove paper add the compound and spin away.

    As far as how often there are multiple factors involved including how often you cut and if you have sand and debris like I do. If the paper test is really not too important than maybe once a year will be fine. Or less for that matter. The unit has never not cut....I don't know what is considered " dull" to where sharpening is a necessity. The steel strength of the mclane blades has to be much better than great states to where it would take a lot to seriously degrade the blade. As far as being razor sharp and cutting paper , no knife regardless of price that I know can keep on cutting paper at an angle forever without sharpening. Now that I think about that it makes much more sense what reeljake said about the paper cutting test. Its not vital. My main pocket knife I keep with my at all times when i first got it of course could go through paper no problem, its still very sharp and cuts things easily but it can't make a perfect slice though an entire paper anymore like it did day one. It probably would take sharpening weekly to keep that up. I'm going to sharpen both push reels once more and do my best to get a perfect reel to bedknife distance and then leave as is for the next few months and not even worry about it.

  • 9 years ago

    Thanks for all the info Champ. I talked with the gentleman from CL yesterday and he seemed to know a lot about it as he had received advice from his golf course on how to maintain it. He is going to let it go for $100 including the grass catcher. I plan to pick it up today.

  • 9 years ago

    So is it the greensmower I have, 10 blades? Here is the sharpening kit part needed. Comes with special compound and brush and the sharpening manual. The main manual is online I dont think the sharpening one is. Not sure.


  • 9 years ago

    Dang I thought you were kidding about mowing on painkillers...Glad you have a powered model now!

  • 9 years ago

    Wow. So what I day. I went and picked up the reel mower. The guy was also selling a motorized Jacobsen reel he had got from his golf course. He said it was an 11 blade!! That thing was a monster. it had huge roller on the back to flatten the grass after it was cut. I just don't feel like dealing with the extra maintenance of a power reel so I bought the McLane greens manual. I got it home and long story short, I think that's going to be a next year thing. As much as I thought I was maintaining my grass low with great states, it is nothing compared to the greens mower. The grass is too high and I can't power through it. Even if I could, it would leave my grass 50% green at beat because I'm cutting off at least half of the leaf and the mower is at the top setting. Champ, I am going to disagree with you about which lawnmower is easier to adjust the bed knife to reel. The McLane was a pain. I just think you get more control and out of the great states.

    My plan now is to backlap the McLane and get it adjusted for next year!! I hate this year is a loss but still well worth the purchase.

  • 9 years ago
    last modified: 9 years ago

    Ya I should have been a little more clear on what I meant. The Mclane to adjust reel to bed knife requires 4 bolts to be messed with. 2 removed and two loosened. Or 4 loosened. One of the two. When I do it tomorrow I'll update since my memory is not the best. BUT once the screws are loosened or removed the entire reel can slide up and down as necessary. I'm going to chronicle this next sharpening session with pen and paper and attempt to be clear concise and efficient in my presentation when I post. To me the great states going back and forth and adjust ting one screw at a time without seeing much if any change is not as simple as just bang push or slide the reel to the bedknife and tighten the screws tight . The manual actual days just bang with a hammer and tighten bolts. Unscientific and crude but fairly easy when you think about it. My initial issue was just not knowing how to feel and know where the best spot is for resting the reel against bedknife. In going to let a simple sheet of paper take the guesswork out of it. In essence I could be blind and deaf and still be able to adjust the bedknife with the process I'll be doing tomorrow. It might be easier with a second hand because it would be nice for one person to hold the reel frozen in place after adjusted while someone else tightens the bolts. that's reel to bedknife. ItsThe sharpening part that is annoying because the chain guard has to removed the master link found removed chain removed and reel sprocket removed. Then backlap handle bar installed in its stead.

    You need to have the tools.

    And yes if your grass is high you cannot just make it greenslevel in one pass with little effort. You are going to want to use the great states to lower it little by little till you get to 2 inches probably. Maybe a little shorter. With Jakes power reel I cut the first pass no problem and no effort. Then I used the greens mower. And my yard was about 1.5 or 2 weeks without a cut. In my eyes it was very long but it may still have been shorter than yours or similar. I don't have much knowledge with how fast Bermuda grows at longer lengths, time between mowings at that range, my grass has been short so long. I used to use the husquevarna rotary when we first moved in. I always had a rotary at beginning and when I first got my first reel (not the Specialty one) I had the rotary to shorten it down first. It's hard to take a lot of leaf off with great states or anyone. That's where my rotary came in. On rotary I'd use Lowest to second lowest setting. But good thing about great states is you can raise the height quite a bit to do your initial cuts. Then switch to Mclane when you get closer to one.

    Don't make it a next year thing. I forgot where you are located but regardless June I think is prime time for Bermuda anywhere. You can scalp the yard in one day ( utilizing multiple mow settings, essentially mowing the yard two or three times in succession. Your yard will grow just fine and recover after the shock goes away. Or you can do what I should have done and taken it down 1/3 cut every few days. No matter which you do , don't let the upgrade sit on the sidelines. Play your best man. If it were the off season aka winter than ya, let her sit . You've got a lot of prime time left in the growing season to dominate not just your neighbors but also your own status quo. Mclane will get you there. 100 bucks thats a great deal.

    I cant wait to bust out the new mower again. I'm like a kid at Christmas when I received it. That combined of a new toy and my love of yardscaping equals I couldn't let something new for the yard sit and collect dust even if someone paid me to.

    I've seen the Jacobson on YouTube very cool!

    Also, are you absolutely certain you are at one inch level? I know I wrote quite a bit above on the matter but you want to make sure that you are on the Bottom row of holes on the wheel bracket and the wheel bracket should be protruding and sticking out from under the back bottom side of the reel mower body. And the chain link cover middle chain guide bracket should be bolted on , on the bottom row also. And lastly the front reel should be showing its biggest gap above the bolts which allow it to slide up and down rather than the gap being under.

  • 9 years ago
    last modified: 9 years ago

    The last pic shows a bunch of holes buts it's actually a mirror image of other side. The chain cover hides them but u can see the 3 holes and 3 holes side by side on my last picture. The tiny ones that are empty. When you drop the wheel bracket to lowest level like mine shown on the first pic then drop the chain link thing to last also. And the second pic shows the reel bolts and the gap I was talking about. It looks distorted on my phone so may have to click picture. To see correctly.

  • 9 years ago

    I wish I was joking Jake. Wish I didn't have to take pain medicine. I take pain meds every day . Every 4 hours. It's annoying and effectiveness decreases because of tolerance. They cause drowsiness too. Without them not sure how I would make it. I'm getting some injections soon to help with the 5 disc bulges that recently worsened. And also second injections for the arthritis building up.


    No doubt the power reel was ez pz. I was at Lowe's other day and felt the Mowers. The power ones with drive. They are heavy as tanks just like Mclane. But the power drive is what makes it all ez. Now, with the engine off its not fun relocating such a unit! Lol . But ez pz to use with engine on. I'm going to do the full cleaning soon. We got rain this weekend. My grass is already rebounding. It's very exciting. With the 2/3 week result turnaround on organic use, I should see some amazing growth in the next week or two.

  • 9 years ago

    I do apologize sherm if my words and opinions weren't parallel with your own experience. But I think its temporary , and I hope your frustration today was just result of a first time experience on the maintenance side and a slight miscommunication of ability on the cutting side. When I first took apart the Mclane I felt it was a pain. Took forever. I hated it. The first time I did the sharpening. Hated it first time I adjusted reel to bedknife hated it. But with the experience and first time woes over with, my confidence has increased. I know I can do it again what I previously did and it will be easier the second time.

    Then other day I lowered wheel bracket. First time. I really did kill myself on the concrete garage floor cursing the Lawn gods because I could not remove the sprocket . And I couldn't give up. Brains and leverage. Finally got it done. It was terrible experience. First time I did the chain cover was terrible. When I had to redo it because I put it in wrong spot, stupid mistake. I was upset cause it was hard. You will see what I mean when or if you adjust yours. The second time was easier! I can do it again if I wanted to and won't be as challenging.


    Great states same thing first time I had to adjust mower height it was hard. Sharpening hard. And reel to bedknife....hard and I'm still not fully understanding screws. Mclane movement makes more sense to me. Because I can see the effect easier and movement.


    The next time u work on Mclane it will be easier and faster. And if previous owner worked on it and has removed sprockets and greased up things well. Shouldn't be a big deal. Experience is the ultimate teacher and confidence builder. If u were to bring me the reel to do for u at this point after this thread and posts from others here and publications online, I'd be very confident in the quality and speed that I could perform the work. What makes things hard for me in the past were my physical issues and lack of experience and knowledge. Now my main detractors are my own physical disabilities. I enjoy mowing edging and being upright, but it's a different animal for me doing maintenance .I've had rheumatoid arthritis since age 15. Over 20 years.


    Maybe I'll try to video some of the work I do tomorrow.








  • 9 years ago

    One last thing for the night. I don't believe it's necessary to remove rear sprocket when lowering or raising the wheel bracket. I did it because manual said to, but after accomplishing task , I believe it isn't. The bracket will lower regardless of sprocket by removing the 4 screws / bolts necessary on each side and sliding down or up.

  • 9 years ago

    Champ what do you do with the chain cover after changing the wheel position? Unless I did something wrong, it won't fit.

  • 9 years ago

    Upload a pic of chain side right now with your phone .

  • 9 years ago

    Or to my email champion6sigma@live.com

  • 9 years ago

    Did you figure out sherm? Hopefully u were able to see the bracket thing within the chain cover (behind it hiding) that I wrote about and it's held on by two bolts. With a nut on back of each one. The bolt by wheels is ez the one that goes into reel area is super fun. Lower that guy to last set of holes yours is probably at top level . Remember it's 1,2,3. Or ABC use level 3 aka c.

  • 9 years ago

    Hey Champ. Somehow when I posted last night I did not see your post with the pics. A lot of info but all of it was helpful.

    So I looked at the lawnmower and all of what you said makes sense. My wheels are currently set at the middle position meaning all 6 of the holes on the wheel bracket match up with the holes on the frame. From the pics, your mower is one setting higher than mine meaning I could go up 2 notches if I had to. I went up one and it was still hard to push. That was also the setting where I couldn't get the chain on. I now see how I can adjust the bracket where the cover secures to. You're right...... the bolt by the reel looks like a huge pain.

    I am going to take your advice and see if I can get the reel to work this year by going up on the height. I still think I need some work on adjusting the reel to bed knife. I watched a lot of videos and it is amazing how easily they cut paper. I still need to get mine to cut a folded piece of paper. It will likely be this weekend before I have time to play with it. I will have to be careful how much I take off.

    Another question. Do I need to wedge something into the handle where it attaches to the mower so it won't keep pivoting?

    Thanks again for all of the help.

  • 9 years ago

    Not sure if I understand what setting you are on. If you cant see the rear wheel bracket protruding from your reel mower base exactly like mine is , regardless of which set of holes you used to secure it, it's wrong. (If you want the highest setting aka highest HOC) The holes you use really aren't of any concern . It's the position that makes the difference. As I stated above , my bracket was in the middle of the 9 holes ....that is how the factory sends out every Mclane unless u special request Alternative. Middle setting. So I lowered mine down one level and now it's 3 level or C level . Without that you cannot mow at one inch. Same with every single Mclane ever made because I had fun reading the manual to every model they make. In my attempt to find the model manual for my new power I spent hours googling for info. Every Mclane has the ability to mow at a high setting ONLY accessible by moving the rear wheel bracket on any machine they make to its highest hoc (usually lowest notch) setting which means lowering the wheels further below the mower base . Which in our case is lowering the bracket kind of like what people do to their trucks when they lift it they get taller Springs. Wheels stay on ground and vehicle (mower body) raises. My new power reel can do 1.5 inches I think highest setting. Cannot mow at that height unless I take apart entire machine and move wheel bracket in rear down. The front is ez. Back , they say in manual on power one best that factory does it cause of work involved.


    And I don't believe the test should be done with folded paper . every single document I've ever read even one from 40 or 50 years ago ...says use newspaper or s single sheet of paper cut into strips. I recommend computer paper. Basic copy paper. One inch or two inch strips.


    I didn't get to backlap today hoping tomorrow is the day.


    Anyway to send a pic of yours with the chain cover off so I can see what you have going on . And also while at it the side shot of the roller area bolts.


    The pivoting of the handle I mentioned above I think it's that way to allow flexibility in push height. If you tighten the bolts on the bracket holding the handle to mower . Use a socket set and a wrench or pliers for the opposing nut holding bolt or screw (I don't know correct terminology) ....you can tighten enough so there is no play. I'm thinking it's designed to move so u have some adjustment if while pushing u can move up and apply more downward Force. If you need speed and want to go lower center of Force to ground for power and stability or whatever I can't figure out physics of it then simply push down and then push forward. But if it's annoying I've tightened the hell out of bolt before and it will stay put. I ended up putting it back because I liked it better with pivot. I can tighten and put loctite also if u r dead set on it being fixed.

    I just used tape measure to measure floor of garage to reel bedknife. I'm at one inch or one inch and maybe 1/16 or 1/8 over an inch but either way I'm at an inch (manual itself says greens mower push goes to approx. An inch it's not perfect. And the mower is level across , parallel to concrete . Not at some weird angle. I've spent hours and hours now reading and rereading these manuals and even finding discrepancies between versions . On my power one there is an error in labeling of a and b between documents and now that I found a better version I've got the power reel at one inch perfectly.


    Can't wait for more growth so I can power up and plow away with it.

  • 9 years ago

    t's on the middle setting like you described above. The front roller is adjusted properly too. I'll probably have to move the wheels to put it on the highest setting to get it to cut and gradually lower.

  • 9 years ago

    I don't know how much this pertains to your mowing machines, but when I saw that some of you had replaced adjustment screws with bolt heads, it reminded me of something. When I was in high school I rode a dirt bike after school. Within a week all the bolts were loose. Of course some were more important than others, but I ended up drilling 1/16th inch holes through all the bolt heads and running safety wire through them to keep them from backing out from the vibration. I tried using Loctite but that stuff, at least back in the 60s, didn't work for me like the safety wire. If these mowers tend to loosen up after a few weeks, you might consider the safety wire approach. Here is a link to some tricks of the trade.

  • 9 years ago

    Nice! Yes yours looks just like mine before I did the adjustment.

    In my opinion, if you intend to go below and stay lower than an inch ....I say just keep it as is but start lowering your yard now with the great states. Just keep on taking little by little off . It's ez to adjust that one for height.

    I'm curious what setting u have your great states on.....and height your yard is that you attempted the Mclane pass through. The fine adjustment on Mclane doesn't do too much and I used too have it just slightly hire on the sliding front reel adjustment than u do now. And of course on the middle rear level (standard). At that setting when cutting it's well below 0.5 and I can run the great states after at its lowest .5 setting and it won't touch a thing.

    A greensmower isn't meant to take off an inch or two at a time. I took off about close to an inch at one time with it. It can be done because that's what I did last week. At the height u have it now which is what I changed mine to, ignorantly believing I had it at one inch. I mowed down yard from maybe 3 inches to about 1.25 with the power reel, and then used the Mclane greensmower push at the hoc that u have set now. ( not ideal cutting so much at one time) And it was effort. And not something that I should have done. So if your yard is higher than 1.25 which I'm guessing it is, I understand your frustration. If yours is at 2 inches and u use that Mclane at your current level it mjght not be possible. Even raising hoc my adjusting the rear wheel and it still won't be ez. Taking 2 inches off might be near impossible without practically running and many passes. Even then maybe not possible at all.


    Be nice if u can borrow a rotary and just quickly get yard to 1 inch..or 0.75 if u can find one but at that height if u haven't leveled u might scalp. .... Then start using the Mclane after u get to at least one. Taking half an inch should be ez . And then finally once u get to the Mclane level and u are mowing every 2/3 days u will thank yourself for the upgrade. It will be a walk in the park and your grass will improve. Just do whatever it takes to get close to the hoc of your Mclane currently. After that it's smooth sailing. To bad your not in San Antonio. I'd take care of it for u. No yard is too hard or high for me .


    Did the guy tell u last time it was sharpened.?



  • 9 years ago

    Wow. Dchall I've never seen safety wiring. Cool trick.


    Article pays homage to the r and d of ww2. It's true. Where would we be without military spending or military tech/resesrch.


    I don't think the push mower will have issues with screws reversing but perhaps an engine one might. There certainly are quite a few bolts. I do tighten things pretty hard.... I'll have to just keep my eye on things in future. As far as I remember I haven't had issues with any thing of mine having an issue with screws coming off by themselves.

  • 9 years ago

    Champ my yard is very lush and thick so I get the choppiness look if I try to take off too much with the great states. It will just skip along the grass. I don't believe it would be beneficial to lower the great states. I actually just raised it last week because of the choppiness I was seeing. That's what I use my rotary for. I use it to scalp in the spring and to maintain my yard at a desirable level if I go a week without cutting. For me to use my rotary to cut my lawn low so I can use the McLane would probably do more harm then good. I would be willing to bet if I did that, my yard would be about 25% green if even that. I don't have any desire to do that. When I get home, I'll take a pic of the little strip I cut with the mower at the current setting.

    I don't think the mower had been sharpened at all. Maybe that's part of the problem. I sharpenedy great states a year ago and the edge of the blades still look pristine and shiny. No rust, dents, voids, etc. That's what I am looking for from the McLane and I need to backlap to get there.

  • 9 years ago

    The Mclane has rust ? Dents? And issues ?

  • 9 years ago

    No. It's just not shiny like the great states

  • 9 years ago
    last modified: 9 years ago

    Look forward to seeing pics of the yard.

    Pics of the Mclane manual on sharpening. Sherm.

  • 9 years ago
    last modified: 9 years ago

    Here are pics of the lawn. This is with the McLane set at the level it's at now. This was also with me pushing forwards and backwards multiple times with the lawn mower.

  • 9 years ago

    Now that is a cut!!!! Wow!!!! You definitely had close to a putting green with that. The previous cut was with your great states and u said u just raised it right? Cause of issues of bouncing....


    U have beautiful yard and great green.


    U can have green at the Mclane cut your showing but will just take a few days for the surface to regenerate. It's a shock really seeing what half an inch truly looks like when u have been mowing higher previously. I've been cutting shorter than that for a long time now.

  • 9 years ago

    Your yard sherm, is in much better condition than mine and you are an excellent candidate for shorter cuts and the ideal height of Bermuda, which the Mclane will achieve beautifully.

  • 9 years ago

    Thanks champ. I just have to figure out how and if I want to invest the time in lowering it. I will say this..... I cut it short with my rotary a few weeks ago to keep it low and there were a few spots that took a long time to recover and some of them are still recovering. We shall see.

  • 9 years ago

    That cross section shot is a great demonstration of how Bermuda grows. It's like miniature trees, the Brown stem has to be manipulated to control height. The top growth is all you should be cutting to Maintain the green top

  • 9 years ago

    Good point Jake. Many people out there have no idea that most of the grass is brown and only the top is green.

  • 9 years ago

    Also, sherm, cutting low with the rotary and getting sections scalped which take long to recover isn't a great comparison to using a reel and cutting low. A rotary will get a true scalp and give you sections truly lower than whatever you set it on or the lowest it can go, so if yours is 0.75 you surely will have section and lower and possible some 0.1's if ground is hit. If you set your mclane at 0.5 you are going to get 0.5. Not a gamut of levels like on the rotary. Recovery will be better, HOC will be spot on, and your grass will flourish.


    You just have to have faith in the mclane and the bermuda. If you were completely satisfied with your yard and equipment...you wouldn't have gotten the mclane or been looking. Get the mclane height up like mine...(1 inch)...and make just a pass or two with great states if possible. It will be the last time used as long your mclane is working.


    I just went out with the push mclane today. I really wanted to use my power but I need to do some maintenance on it first before I really go at it again. ..I'm going to get the equipment tomorrow to siphon the gas....I've got to go get some gas....been awhile since I've had power equipment here so I might as well dump the little I have left in my old container.....I'm getting fresh oil...and I'm going to clean the filter or buy another one if its available. I'm considering a new spark plug. I had some medical appointments and things come up and we had lots of rain this weekend....just didn't happen yet. As you know my yard was cut super low...and now its right above an inch. What I did with the mow today is just skim the surface. I was able to push the mower with 2 FINGERS. bruce lee style if you will lol. i can't do that on the 30 or 40 degree incline i have but on a regular back yard or from what i've seen of pics of your yard ...ez pz anywhere.


    As long as you are comfortable with a lower yard and being in the yard more frequent...the mclane push is a peice of cake when you are not having to take off 75 percent of the blade or more....which looks like where you are at now on the cutting level settings. pushing the mclane should be no harder than pushing it on concrete....you just have to get to the frequency required to only trim and shave the top.

  • 9 years ago

    Confidence and motivation :)


  • 9 years ago

    Champ, any advice on how to get the screw back in that holds the bracket for the chain cover to the body? As you mentioned, the one by the reel is a pain.

  • 9 years ago
    last modified: 9 years ago

    thin pliers or wrench. now that i think about it the pliers might have been too thick. I used a wrench. used the hole or ring side rather than the open side that looks like a C claw. If you have thin enough needle nose pliers with length that might work....or try taping the screw to something long and thin. I had to balance the screw in the ring and carefully push it through hole and grab it with fingers after it went through. then once its in fully you can just lose pressure on the inside of reel to screw in the outside part. So I used the wrench end to keep pushing on the screw (not the ring inside part that i had balance but the pure metal part against the head of the screw to keep steady while i hand turned the outer part. Then once I got close enough I had to tighten with a wrench on the outer part while attempting to keep screw on inner part from rotating so I used the Ring part once again to barely get around it and keep the inner reel part steady. Bad lighting and by yourself and its not too fun of a task. Just make sure to get it right the first time. I mistakenly put mine in the middle set rather than last and had to redo.

  • 9 years ago

    Thanks champ. I was able to do it by removing the cover for the reels that makes it a front throw. I could easily install after that. Thank you.

  • 9 years ago

    Nice I'll try that next time

  • 9 years ago

    The other day I backlapped the mower by reversing the wheels. If you do that, you can pull it to backlap but it still is tough. I wasn't pleased so I stole this idea from someone else. Not half bad. Even after backlapping, my grass is just too high and too thick to cut with the McLane. I cut my yard with the rotary the other day and tried to lower it. I could cut about 2 to 3 40 ft strips before I had to empty the bag and even with that I still can't cut with the McLane on the highest setting. My plan is to hopefully maintain my yard with the great states. In the spring time, I will put in the effort to scalp with the rotary and then go as low as I can with the McLane reel. Not looking forward to that. My spring scalp is a job and a half as is.

  • 9 years ago

    What exactly is the height of your grass?

  • 9 years ago

    I'm guessing an inch and a half to 2 inches. Purely a guess though.

  • 9 years ago

    The only thing I could suggest is do 1/4 cuts of the new line of cut, mowing primarily 75 percent of the stripe you previously did. Then you should only have 25 percent of the usual resistance slowing the blade down. Mow two cross lines from whatever corner you want to start at so that when you complete the entire yard at whatever direction you normally do....you have zero grass slowing your starting momentum (the first 2 ft approx of the new line is already done from the 2 cross lines you made at the beginning). I've done this before to expand my yard and to cut into my neighbors area. I can cut her 3 inch grass like this no problem. The issue I think is not that the mclane is struggling to cut....anything....its that the intense amount of leaf blades and grass that fill the entire reel bed cylinder clog up the space available for the reel to turn. the blades are not being continuously cut after the first cut and so if you are cutting to 1 inch from to me looks at least 2 inches or higher (when you were at 0.5 - 0.75 (I don't know what the measure is honestly when the rear wheel isn't at highest)...in my opinion based on the first pic you sent....i'm not sure what the actual cubic mass would be of grass entering the cylinder...but it will surely overload the ability to turn. When I've cut high grass in the past I've had to reverse and empty the cylinder....spin the wheels then start again. A power reel would have no trouble in maintaining the spin of anything in the realm of grass/paper/twigs///whatever isn't metal etc...


    Does that sound right? I sorta just thought about it right now. I know cutting a smaller line like 25 percent or so makes sense....but it just came to me what really is causing reel to bog down. Same thing that happens with a rotary...its not often....but super high grass (foot or higher)can bog a rotary down even with my mammoth size husquevera with huge engine. I know I mentioned the power reel above but I still must be realistic with its capabilities as well..I know it will take care of your yard super easy just as like it did mine which was higher than yours but not as dense in many areas. I should have taken a before pic. That said if using a power reel on a yard that was 4 or 5 inches high...it would maybe choke. I can cut 6 inches with my rotary. I think a power rotary will surely handle higher grass more so than a power reel.


    Starting momentum by doing the cross line will surely help and then just cutting 20 or 25 percent of a line.


    I'm sorry you are having so much trouble. Once you do get closer to that 1 inch mark it really will be easy. I promise you. I know in my bruce lee vid its hard to see but there is grass flying...its probably .1 to .2 of an inch on my most dense areas. I'll take a fresh pic tomorrow.


    Cool trick with the socket wrench. A lot of people do that but with a power drill. I bought the kit when i bought mower, you only get free shipping on accessories when you buy a mower...


    After backlapping could you cut paper unfolded with the mclane?


    I actually still haven't sharpened either reel...and haven't done the maintenance to my power reel yet. TOMORROW is the day!

    I bought the siphon for the gasoline today on special, had a coupon! lol

    Tomorrow I'm getting some oil and gas and I'll be doing the maintenance to the power reel and then also to my trimmer which is failing to start. Draining oil from both machines.....and gas....and filling up. Also will get some carb cleaner. Seeing if any additional additives will help. And also might get that spark plug.....when I'm feeling my worse...which has been this last 2 weeks, I sometimes can only do the bare minimum, which is cut grass, and setup sprinkler if needed. I just started a new 75,000 dollar medicine on Friday, and I get to have fun injecting myself at home. I think its helping slowly.


  • 9 years ago

    It'll cut paper on one side but not the other. It may just be a reel to bed knife adjustment.