Software
Houzz Logo Print
andrelaplume2

Echo PB 2100 blower new carb issue

9 years ago

The 12 year old blower was not running well I bought a Zima carb kit off Amazon. At first I just installed the new fuel lines because they seemed worn as was the grommet. At first it started but then I noticed no matter what i did I could not get the primer bulb to fill with fuel. I decided to put the new carb on this morning.i The primer bulb filled and the unit started right up and it ran fine until I took my finger off the trigger and now it stalls. I have no idea how to adjust the 2 screws that are on there ....can somebody help me. Or if you have any thoughts as to what is wrong please advise. Has a new carb new plug new fuel lines and new fuel filter.

Comments (53)

  • 9 years ago

    Definitely two screws

  • 9 years ago

    that's weird. it should resemble this. the way you explain your problem sounds like it won't run with your finger not on the throttle? does it restart ok after it dies?

    Zama C1U-K42B CARBURETOR

  • 9 years ago

    hi, does your carb look like this 1? the circled area is the idle adjust

  • 9 years ago

    I think so..will look tonight..I definitely see the two screws below and was.monkeying around with them to no avail...is there a procedure to set it...

  • 9 years ago

    Yup...now how do iseybthesev3 screws...do far monkeying with the middle idle screw makes no difference....starts but stalls at idle

  • 9 years ago

    sorry guys...it seems to start up an run until I take my finger off the throttle...before I can adjust any screws it stalls.

    I adjusted the idle so that it was a little past the metal that rests against it.

    I think the high screw is the one on the left and low on the right. Does any one have advise for setting them. I have had no luck.

    Is there anything else that can be going on?

  • 9 years ago
    last modified: 9 years ago

    If engine fails to run with 2 turns out from seated begin with 1-1\4 or 1-1\2 , otherwise excellent info site advice from 300 ft !

  • 9 years ago

    I will look at the link. I did fidgets around with it and I got it to idle and I got it to remain running and actually used it and it seemed fine. I let it sit for 10 minutes and it would not start again. my guess is if I let it get cold enough it will start again so maybe there's still some fine-tuning to do...

  • 9 years ago

    Add q little fuel cleaner may also have some residual fuel gunning within the carb circuits .

  • 9 years ago

    On a new carb..new gas?

  • 9 years ago

    hi, where you able to restart the blower after letting it sit?

  • 9 years ago

    I tried before bed...would not start. I was surprised because it was running at idle.. at throttle...fine for 10 minutes...no stalling.... thought it was good to go...can't start now...and yes there is gas in there!

  • 9 years ago

    Yep has happen before some carbs are random tested and you may have received one lol.

  • 9 years ago

    So add some seafoam and try again...

  • 9 years ago
    last modified: 9 years ago

    Concentrated carb cleaner would be preferred . Sea foam is a long term fuel conditioner , not a spot form cleaner . 2 ounces within fresh fuel . Let this mixture sit overnight then attempt to start once it does keep it running via primer or choke . P.S. you have ensured there is no fuel filter attached to the fuel pick up line within the fuel tank ?

  • 9 years ago

    Right now fuel filter attached in tank. Will start over with link above...failing that will try fuel additive for carb.... like I said...started...adjusted...was idling for 10 minutes and in fact used during that time...then would not start after cooling off....

  • 9 years ago
    last modified: 9 years ago

    Like I said sounds like you have pulled in some form of dirt , gum which has fouled the internal fuel circuit . How old is the current fuel filter ? You have to dislodge or dissolve the obstruction . Jet removal may assist in this endeavour during your inspection & cleaning . Follow the link , after cleaning , cannot be much of a serious obstruction .

  • 9 years ago

    I think I posted earlier.. brand new fuel lines brand new spark plug brand new fuel filter brand new air filter and brand new carb...

  • 9 years ago

    Yep I see that now last line of your original post . Since primer is filling and depressing properly , then dirt or debris is the causation . Ensure to remove the jets during your cleaning and all should resolve .

  • 9 years ago

    it's hard to tell, but are you getting spark during these no-start episodes? your blower has been around for awhile, it could be something else. a good little tool to have is a inline spark tester.

  • 9 years ago

    I have one it will give it a whirl...

  • 9 years ago

    12 yr old Blower , what are the odds of faulty carb and ignition module ? Never say never ! lol.

  • 9 years ago

    The carb is new.. I guess it could be a dud

  • 9 years ago

    I put the screws in again ...backed them off enough to get it running unfortunately I couldn't get the idle adjusted adain before it stalled and then wouldn't start. I checked there is definitely spark. I am now cleaning the muffler and screen and then we'll try again

  • 9 years ago

    I think it's time to give up. I clean the muffler and the screen and put it back on I swapped out the generic plug for a brand new nkg .. I was able to get it started and to get it to idle. But now anytime I try to increase the throttle it's rough or stalls or sounds like it's kicking into gear and then loses power abruptly. I also noticed when it starts I see a little blue smoke come out I don't know if that's normal or not. The blue smoke is only when I start it cold it seems or not fully hot anyway.

  • 9 years ago

    hi, you didn't mention it but how's the air filter? try running it without the filter on. your last post sounds like the adjustment is off.

  • 9 years ago

    Brand new air filter too... Unless this thing is touchy as heck I can't get it adjusted... I think it's time for a new one and maybe my brother-in-law can take a look at this when he has time he has a landscaping business... Thanks for all the suggestions


  • 9 years ago

    ya, i know what you mean. it's frustrating when they don't cooperate. your's did a good job, long life. hopefully your BIL can figure it out, it may have a second wind? good luck

  • 9 years ago

    Would be nice to have a semi-retired backup unit I guess

  • 9 years ago

    Are these Echo units still the ones to buy?

  • 9 years ago

    i've been a big fan of echo's for a long time. i'm not to thrilled with their newer stuff (orange) body's. if your going to replace yours, i tell people to not purchase at the big box stores, if there are lawn mower shops nearby check them out and see what they carry or can order and they can help if there are problems.

  • 9 years ago

    Yeah I usually purchase from the local guy down the street who happens to sell echoes...

  • 9 years ago
    last modified: 9 years ago

    Echo,s at least the two strokes are among the best commercial , saws , blowers or trimmer units on the market . Not impressed with any of the 4 stroke manufacturers on the market over priced and heavy cumbersome blower units . 12 yrs old , compression could also be in question , when in doubt I usually start there . 125 psi after 5 pulls is optimum , blue smoke when cold could indicate worn rings . Not knowing the history of your unit makes it hard to determine all variables . P.S. I do not see where you have indicated , that you used any concentrated fuel cleaner , just assumed that spark may be contributing issue . These carbs are often run then shipped after testing , you may have one . Anyhow best of luck , actually 12 yrs on a blower which run hard full throttle usage continually , is no small deed .

  • 8 years ago

    A year later...brother in-law got it running...believe he said bad carb...it happens I guess...

  • 8 years ago

    happens alot! hopefully it will behave for a while. you have to follow their (manufactures) recommendations when putting it away. glad to hear it received a second chance, good little machines.

  • 8 years ago
    last modified: 8 years ago

    Roflmao , like I said never say never . Even what is thought to be new can be faulty . Although you have not stated it , your brother in law likely found some crude that was within the fuel secondary circuits of what you describe as new replacement carb . As I originally stated these carbs are randomly tested @ the factory due to mandatory Epa certification compliance requirements . Unfortunately you were the unlucky customer . When you get a chance ask your bil if he inspected your carb or just replaced with another new unit . Thanks Bud for getting back to us after this frustration , it helps others understand how even new units can be questionable , just a little left over Efuel can gum up even a new factory fresh carb . P.S Seafoam during usage and storage will prevent future issues , as you mentioned previously Bud !

  • 8 years ago

    FYI - he put a new one in...just my luck..I should have sent it back I guess!

  • 8 years ago

    As I previously advised most carb manufacturers randomly test their carb prior to shipping in compliance with Quality Assurance Certification . Quite often residual fuel trapped with the minute circuits will cause these aggravations . Thanks again for the resolve info Bud !

  • 7 years ago

    I have a similar issue with my PB 2100. Changed carbs,fuel lines , filters. Started right up ran sweet until it got hot then just died. WOuldn't start until cold again then did the same thing. Any suggestions ???

  • 7 years ago

    hi. I suggest looking over the post. your answer has probably been discussed.

  • 7 years ago

    I would test or replace your coil , since the majority of points discussed involved fuel starvation issues !

  • 7 years ago

    same issue with my very old Toro....ran fine till hit...then if I stopped it would not restart,..dealer let me try a used coil...no luck..bought a new Toro...use the old one to mulch up leaves and debride...

  • 7 years ago

    should have said 'run fine until hot...then if I stopped it..would not restart till cool'. Coil did not help.

    I have an old echo trimmer that has been troublesome this year...u can probably find my posts....similar situation..runs rough as it gets warm... I did buy a new carb..might try to replace it... the sucker is 15+ years old so I shouldn't complain. I might get a battery jobber next...or a Stihl. might be my perception but the Orange echo stuff I know ppl have seem more trouble prone than my vintage grey unit ever was!

  • 7 years ago

    Stihl is more prone to a fuel problem than any other Manufacturer , their Proprietary Zama carbs . 99 % of all hot starting issues are coil therm o breakdown contributed . The other 1% are seal related very uncommon .

  • 7 years ago

    echo the Zama right? are u saying replacing the carb won't help...where is the coil..is it hard to replace?

  • 7 years ago

    What application are you referring too Bob ? You realize were discussing Blowers ? Have not seen a mulching blower come through my Shop lately ? lol.

  • 7 years ago

    no sorry my bad I was just mentioning that I had a similar issue with my old old old Toro mower where by when it got hot if I stopped it and tried to restart it I'd have to wait for it to cool down before it would restart. The dealer let me try a coil that wasn't the issue and I just bought myself a new mower... sorry.

    Second issue I'm talking about is my string trimmer that seems like when it gets hot it does not run well it becomes difficult to keep. I have a carb that I never put on but it sounded like you were insinuating that perhaps the carb is not the answer it's a coil or some kind of gasket and I have no idea where are the coil or gasket would even be.. I'm not a mechanic... I sort of know enough from this forum to get by and try things and generally they work.

    it's fine for now I don't want to hijack this guy's question. I will say though the thought of a mulching blower sounds rather enticing!

  • 7 years ago

    blower/vac's have been around for a while. i have a echo es2400. works good, don't use it a lot but comes in handy.

  • 7 years ago
    last modified: 7 years ago

    Bob , the trimmer issue unless 15 yrs old like your Toro mower would be a bad coil if the symptoms are as you have previously described . The faulty coil heats up within 10 - 15 minutes and the engine begins to miss and stumble and then quits like you hit the kill switch . Let the unit sit for 20-30 minutes and it will repeat the symptoms within 10-15 minutes . The coils are under the fly wheel or beside the power head depending on the yr and Manufacturer and Model Designation . If you need more specific info Bob forward specific Manufacturer and Model numbers and approx age . As for Mulching Blowers , I had a B & D electric which Puriated rather than Mulch lol !