Software
Houzz Logo Print
kat_zimmermann20

Laundry closet door disaster!

7 years ago

We just got our new washer and dryer delivered and installed today (yay!), but now we're having some problems with our closet setup.

I can't open the little drawer to add detergent more than halfway! my first thought was two sliding doors overlapping, but then the dryer would get in the way (photo, the bifold door now scrapes on it). There's no room for pocket doors and the hallway is quite narrow.

Any ideas at all are appreciated!

Comments (100)

  • 7 years ago

    You have to be able to pull out the detergent drawer area both for cleaning and to allow it to fully dry out. I take mine out each day. So removing the folding doors each time you want to remove the detergent drawer or open the dryer door (which also appears blocked in the photos) is not practical.


    I would remove the folding doors permanently, live with it to see whether it bothers you, then decide whether to put a nice looking curtain in front or redo the laundry shelving area to make it a little more visually appealing.

  • 7 years ago

    I am really happy with the performance of this washer... the dryer is another story.

    Why aren't you happy with the dryer? I'm on my second LG dryer and have been very happy with them.

  • 7 years ago
    You could gain a bit of depth by moving the hardware for the doors out as far as possible in the doorway frame. Maybe an inch. But the detergent draw will still be hard to access. Flipping the washer and dryer locations would solve the detergent drawer problem, but then you would have to “jump the doors” as my husband and I called it because the washer door will be in the middle. Only the dryer door can be changed on the LG models. I think that removing the closet doors is probably the best solution. The barn door idea is a good one. Note to other people: it is IMPERATIVE that when purchasing laundry equipment for laundry closets that you consider the total depth of the new appliances, including hoses and venting (and detergent draws). Newer appliances are larger than the older ones.
  • 7 years ago

    "You have to be able to pull out the detergent drawer area both for cleaning and to allow it to fully dry out."

    I've had front loaders for over 20 years, and that's never occurred to me. I've also never had a problem with any kind of mold, bacteria, or foul odour.

  • 7 years ago
    last modified: 7 years ago

    it might depend on where you live. in Seattle, definitely an issue but it's not noticeable unless you pull the tray out and look underneath. yuck. if you live in a dry climate, it might not be as much of a problem. I don't take mine all the way out very often though, it's really difficult. I just inspect it every now and then.

    I actually have to leave the washer door open at all times when not in use. inconvenient, but thankfully I have a laundry room that accommodates that.

  • 7 years ago

    Just to comment on need for cleaning... mine gets black and yucky from never being dry it definitely needs to be cleaned on occasion! Do you have any wiggle room to slide both machines to the right a bit?

  • 7 years ago

    "I actually have to leave the washer door open at all times when not in use."

    I do that too, but the material of the gaskets is very different from the material in the soap dispensers, so the likelihood of growing something there is higher.

  • 7 years ago

    Open all those other doors and step back and take pictures of the washer/dryer. I am leaning toward just loosing the doors to the laundry closet, but I want to know what is your view of the appliances. Hey, my laundry is in the garage, so anything inside is a big step up. LOL!

  • 7 years ago
    last modified: 7 years ago

    Depending on your house layout, removing the doors might leave the units too open to the rest of the house, with respect to noise, visibility etc. If so, maybe you could remove the laundry closet doors, but then add a door to the right of it, enclosing the hallway to make a laundry room.

  • 7 years ago
    last modified: 7 years ago

    Some people have laundry rooms pretty enough to put on display. Sounds like a challenge! maybe put nice cabinets with doors above to hide all the detergents, and a panel to hide the hoses, etc.

    or this blogger hid all that stuff with a curtain. I really like how he put a countertop over the machines.

  • 7 years ago
    last modified: 7 years ago

    This laundry room makeover is my favorite makeover in all Houzz. https://www.gardenweb.com/discussions/3792622/sad-ugly-laundry-room

  • 7 years ago

    Cpartist.... my dryer has regular spells of horrible vibrating. 2 techs that Samsung sent out had no idea what the problem was... 1 tech on extended warranty also had no idea. I told them just google shuddering LG dryers, it’s a common problem! My husband took it apart after researching the problem. It seems that the wheels do not have bearings and are suppose to be “ self lubricating” as they wear. He noticed uneven wear on the shafts that the wheels go on, along with inside the wheels. He coated the shafts with wheel bearing grease and it stopped for about a month I guess. Now it’s back at it. It doesn’t matter if the dryer is empty or has a heavy wet load of towels. I have made a post about this before and tried to upload the video but couldn’t get it to load. I’ve had the dryer for a little over a year.

  • 7 years ago

    BF has a point. In that space, you almost CAN'T have a front-loader, because you can't leave the door open.

  • 7 years ago

    " In that space, you almost CAN'T have a front-loader, because you can't leave the door open."

    It only has to be open a few inches, just kind of ajar. You don't need to leave it wide open.

  • 7 years ago

    LGs have a magnetic catch that holds the doors open about an inch

  • 7 years ago

    Toronto, I don't think there's even room for that. And the closet doors would be closed, so not much air circulation. Louvered doors might help if the washer door can be left open.

  • 7 years ago
    last modified: 7 years ago

    rpwoodard,

    I'm the one that mentioned returning the machines since the stores I've purchased from always have an offer of return & exchange if not happy with the machines, usually within 30 days. I'd be surprised if they didn't offer Kat that option. At the worst, she may have to pay a restocking fee but it'd be worth getting something she's happy with in her home.

    But, even with top loaders Kat needs to measure carefully to make sure the dryer door will open.

    Kat, not sure if it's been asked, but what machines did you have there originally?

  • 7 years ago

    The original poster's new washer & dryer were just installed 3 days ago ...some of the suggestions are to replace the 3-day old machines with top loading machines? What would they do with the machines they just purchased?


    Exchange them for a set that will fit the space at the store from which these were purchased.

  • 7 years ago

    I returned an oven the day after it was installed, exchanged it for another one.

  • 7 years ago

    My mother also has a set of LG's she loves, and she had the same problem at her new apartment. Since the back wall adjoined a closet, I routed the exhaust pipe for the dryer to the other side, and switched the washer with the dryer; washer to the right, dryer to the left. It's less practical for large loads because now the doors open towards each other, but it does not seem to bother her so much.

  • 7 years ago

    Thanks for all the responses! Returning the set isn't an option - I replaced a top loader on purpose because I hate top loaders.

  • 7 years ago
    idk why it wouldn't let me keep typing after I took the photo, but I added it to show that barn doors won't work either (which is a shame because we love them) and neither will closing off the hall as it's quite short. We took the doors off for now and honestly might just leave them off....the machines are really quiet so sound isn't an issue, just appearance
  • 7 years ago

    That looks just fine to me, I wouldn't have a problem with that at all, hope It works for you!

  • 7 years ago
    Keeping the doors off seems like the best solution. Enjoy your new washer and dryer. I really like my front loaders.
  • 7 years ago

    I like the doors off. I would try to find a really nice set of cabinets for over both.

  • 7 years ago

    " We took the doors off for now and honestly might just leave them
    off....the machines are really quiet so sound isn't an issue, just
    appearance"

    I don't think it's so bad. They're laundry machines, and your family makes laundry. I'd just ensure they stay clean and live with it.

  • 7 years ago

    alter the door opening and have doors that swing out ?

  • 7 years ago
    Remove the doors and add a curtain?
  • 7 years ago

    I had a similar situation with my LG pair, but it was that the washer was right next to the new furnace. It made the furnace front and filter unreachable. So I moved the washer to the right and stacked the dryer on top. The drain reached with no problem, and I got longer hoses. Since my dryer outlet was on the floor, I got a longer cord. You don't have that problem.

    It also allowed me to add more shelving up the wall.

  • 7 years ago
    Think long and hard about stacking. When stacked, if you have any mechanical issues, its going to take two people to get to the working parts. If you dont have some sort of maintenance plan, you might be charged for the 2nd person.
  • 7 years ago
    Can you cut out only the sheet rock behind the units to give you a few more inches and push them back a bit?
  • 7 years ago
    Summer, thanks for the tip about challenges accessing the rear of stacked machine for repairs. I’m planning a laundry room & was considering stacking.
  • 7 years ago

    Summer, good point about access for repair. Just to throw something else into the mix: I recently spoke to an appliance repair guy to learn of his experience on repairs. He said with the new water-efficient machines, that the front loading ones perform much better, because they get the benefit of the tumbling. He’s gotten calls from people that have pulled items from their top-loading washers and the items aren’t even wet all over...so how they could possibly be clean? His example involved someone washing a comforter, so maybe it’s less of an issue with clothes, that can move around.


    FWIW, in terms of brands, he said it can be hard to get parts for LG and Samsung and that in some areas, it can be hard to find some to repair them (in our case, those repair guys are about 45 mins away). He likes the the Whirlpool family of products and all their subsidies, which include Maytag, KitchenAid etc. ; GE is good though he said the replacement parts are so $$$, he calls them Generally Expensive. I noticed that Consumer Repairs gives LG W/D high ratings, so who knows? But maybe call around to make sure there’s a repair person in your town?


    (Hmmmm....are we veering off-topic too much??? Sorry Kat ;)

  • 7 years ago
    Not too off topic, a good point! we're in the suburbs of a major east coast city though so I'm generally not concerned about being able to get things or find a decent repairman
  • 7 years ago
    last modified: 7 years ago

    Yale Appliance info on most reliable brands

    https://blog.yaleappliance.com/bid/86332/the-least-serviced-most-reliable-appliance-brands


    "Samsung and LGs real problem and what will upset you is their lack of service techs in the field.

    Statistically, you will have fewer issues with these brands, but if you do. There will be problems in finding competent repair"

    So apparently it's a problem in a lot of places. Maybe call around and have a repair person ID'd before you buy (or need them)?

  • 7 years ago

    "He likes the the Whirlpool family of products and all their subsidies..."


    I'm still upset after our Whirlpool washer died after 4 years. I realize quality is questionable these days, but 4 years?

  • 7 years ago
    last modified: 7 years ago

    chloebud, that's a bummer. What broke? Sounds like it was more than just a broken belt.

  • 7 years ago

    Not sure if you have the space on the sides of the machines for this, but have you considered something like this where the door slide back into a pocket space next to the washer/dryer (maybe a future project?)







  • 7 years ago

    Yxk125, that’s totally cool. I want to do that. Do you know how it works? It is using magic hinges or ? Do you know how much extra space you need? (Thickness of the door + 1”?)

  • 7 years ago
    Girl_wonder, I actually found the photo on Houzz, I was looking for ideas when we were considering moving laundry upstairs loved the idea of how the doors tuck back I’ve attached a link to the original photo, it should have more detail on it, I believe they are call pivot doors as well.

    Atherton, CA Contemporary Elegance · More Info
  • 7 years ago

    HAWA Concepta pivot and slide-in pocket door system is one brand. Don't know if there are others designed for large closet doors.


    Doesn't appear that OP has enough room, though.

  • 7 years ago

    Thanks ci_lantro. Using your keywords "pivot and slide-in pocket door system" I was able to google and find others too, including this pinterest page.


    https://www.pinterest.com/LACZI/pivoting-pocket-doors/?lp=true

  • 7 years ago

    Barn door would be perfect. Remove molding and use a bifold barn door

  • 7 years ago
    How long is the wall to the right of your closet? Do you have clearance to install a barn door? Something in a slim design (doesn’t have to look barn like)
  • 7 years ago

    " When stacked, if you have any mechanical issues, its going to take two people to get to the working parts. "

    When the guys delivered my set, the assistant carried in the dryer on his back. Dryers are not that heavy. So getting washer out from the wall is no more difficult than the washer by itself since it weighs the most (like 200lb). Mine happens to be on appliance rollers, but that's another story.

    I happened to go by Lowes today and saw you can order closet doors like the OPs that are sliding rather than folding. They fit in the same space but are thinner, with one side sliding over the other. This should solve your drawer problem.

  • 7 years ago

    Has anyone installed the pivot and slide doors in their W/D area? I stopped by a custom cabinet maker yesterday and she said they can do it, but the widest cabinet door they make is 24", so for my stacking W/D I'd need a pair of doors. But that won't work. My contractor's plan was to put the hookups on the side wall so they can be easily reached. Also, it takes 4" on each side to accommodate the pivot and slide doors (they build a little partition using 3/4" plywood). So that means I'm losing 8" just to accommodate the doors, which would eat into the pantry space next to the W/D.

    This company makes hardware that can accommodate a 30" wide door. Has anyone used them or someone like them?

    https://www.rockler.com/kv8091-slides-full-overlay-pocket-door-system-pocket-door-slides

    Any hope that I can keep the dream of pivot and slide doors on the W/D? lol ;)

  • 7 years ago

    Where are people putting their hookups for stackable W/Ds? This pic shows the pivot and slide on each side. I can't imagine where the shutoffs are -- maybe high in the cabinet overhead?

    https://www.houzz.com/magazine/clever-ways-to-hide-a-laundry-station-stsetivw-vs~57166968

  • 7 years ago

    If you're leaving the doors off, consider adding a nice wood counter on top of the machines and building a fake front to hide the ugly hoses and outlets. This image that rpwoodard posted shows this idea:

    The wood counter hides the fact that the dryer sticks out more and gives the space a more finished look. You can see the fake back wall they created above the counter and below the shelves. This would be something that could be easily removed for access to hoses/outlets. I would also consider upper cabinets instead of shelves, since this area won't be hidden by doors.

  • 7 years ago

    Custom doors sound like an expensive solution. If it were my space I'd take the doors off, replace the wire shelving with closed cabinets, and pretty up the space with paint or wallpaper.

  • 7 years ago

    I love the idea of the pivot and slide doors but I think it may not work in my space. ;( If anyone wants to chime in on another W/D closet dilemma, I'd love your thoughts on my thread.

    [https://www.houzz.com/discussions/washer-dryer-closet-pullout-pantry-design-any-thoughts-dsvw-vd~5662690[(https://www.houzz.com/discussions/washer-dryer-closet-pullout-pantry-design-any-thoughts-dsvw-vd~5662690)

    Thanks!