Software
Houzz Logo Print
webuser_38006643982

Will I be able to install a Sub-Zero refrigerator?

5 years ago

Hi! I’m purchasing a new construction home that I wish had a built-in refrigerator. I want to replace the 36” refrigerator that comes with the home with a Sub-Zero 36” built-in unit. I saw on youtube videos that it may require some electrical/plumbing work. For those of you with experience, please help advise in what needs to be done to have one installed. I have attached a photo of what it looks like behind the current freestanding refrigerator. Thank you!!

Comments (6)

  • 5 years ago
    last modified: 5 years ago

    Water line may be fine if you have enough width for the unit as that usually connects from below however, electrical is closer to the top where the compressor is. So you may need to raise the outlet - specs s/b in the subzero manual for your model.

  • 5 years ago

    Since this isn't integrated the install is easier. Here's the installation manual. Link.

  • 5 years ago

    If it's not an integrated SZ model, make sure you can open the doors fully within that fridge cabinet that you show. As mentioned above, your authorized SZ dealer (not just an appliance store who happens to carry Wolf/SZ) will know how to install it properly. In previous times, I would say to inquire with the appliance dealer what kind of discount they can give on the installation (they cannot give a discount on the SZ appliance itself). But in these crazy times, you will likely have to pay full price for the delivery and installation.

  • 5 years ago
    last modified: 5 years ago

    "I want to replace the 36” refrigerator that comes with the home with a Sub-Zero 36” built-in unit."

    Typically, a "regular" 36" refrigerator that comes with a home is not as tall as a SubZero 36" built-in fridge. Since your pic is showing a fridge cabinet enclosure, will it fit the height of a Subzero? Is the cabinetry across the top as well, and at what height? Subzero 36" fridges are 84" tall. If the current fridge cabinet enclosure you have now is shorter than that, you will need to change it out.

  • 5 years ago
    last modified: 5 years ago

    I installed my 4-foot wide 632. Some notes off the top of my head that I'm going to assume apply, but may not.

    • You will need to install an anti-tip "cleat" and brackets to the top of the unit and the wall; this is above the compressor section, so [fake] cabinetry there should be used to hide that system. I use a panel held on by strong magnets to give me access across the width.
    • Whether the receptacle needs to be moved will depend on how much depth you allowed in the cabinetry for not having the unit squashed against the wall. Generally this should be a single, not duplex, outlet. But if the outlet is hidden, then moving the unit to unplug it will be very inconvenient.
    • I fed my icemaker with RO water via the usual PE tubing and John Guest fittings. No leaks as expected, but I have an extension water sensor or two under there to protect the floor if there is a leak. PE is flexible, unlike copper tubing. Once the toe kick is in place (you can scab on cabinet-matching skin) no damage to the ice water line should occur.
    • I use sections of 1/4-inch underlayment hardwood plywood to protect the [cherry] floor while moving the unit. The unit also sits on strips of this plywood, with a stainless steel sheet on the strips to spread the weight. This, as well as the difference in height when the wheels are extended needs to be accounted for in the cabinetry design.
    • I don't recall moving it when it was full. YMMV
    • Vacuuming the compressors' heat exchanger more often than every decade will be a good idea.
  • 5 years ago

    If this is the installation guide is for your product, the electrical outlet, water tubing, and valve are all in the wrong locations on the rear wall (page 5).