Software
Houzz Logo Print
nanabeth

Casablanca ceiling fan remote??

4 years ago
last modified: 4 years ago

We installed a Casablanca ceiling fan in our bedroom in 2009. We have a wall switch for off and on and a remote that controls the six speeds, the reverse, the light and also has a security feature. The remote has gone wonky. Hunter now owns Casablanca and there are only two service centers in the U.S. They just refurbish the remotes and before they will send me one I have to send them mine. I've currently got my fan working, but we aren't touching the remote, only using the on/off switch because the remote is so touchy and we want the fan on at night. We don't want to be without a fan for the time it will take to send the remote across the country and them to mail one back. I've looked on e-bay and Amazon and no W-62 Casablanca remote. Is there another solution short of buying a new fan?

Comments (6)

  • 4 years ago
    • Yes, more than once. I have checked for corrosion and even rubbed an emery board gently over all contacts to be sure contact was being made. When I put new batteries in and turn remote over it momentarily shows a flash of figures, then immediately disappears.
  • 4 years ago

    I can't offer any detailed directions; my "Casablanca" ceiling fan was made by NuTone in ca. 1990 and is hard wired.

    You might keep in mind that the other end of your communication path is at the fan along with motor control electronics, and failure to communicate could be a fan-located failure. So it is possible that you might get your remote back with a note that there was nothing wrong with it.

    Did you check eBay for an entire fan assembly. Besides gaining a remote, you would have the other half if needed.

    lizbeth-gardener thanked kaseki
  • 4 years ago
    last modified: 4 years ago

    I'm not sure that would fit what is going on with our fan. It is currently working enough that it is running when we turn the wall switch on. We currently cannot change anything with the remote. The remote face is currently blank- that may not be the case the next time I pick it up. It is set at the speed we like, but cannot turn on light or change anything. When the wall switch is on the fan is running. If I take the batteries out of remote, the fan stops. I plan on calling Casablanca after the holiday to see if a universal remote would work with this fan.

  • 4 years ago

    I'm back; the remote issue has not been resolved. I sent the remote to CA and it worked fine for them for over a week. They sent it back and had me reprogram the remote by turning off power at fuse box and changing pegs inside remote where batteries go. I have done this several times and it works for a short time and then the remote goes blank again. I have sent it to CA for the second time and same story-it works fine for them. They assure me it has to be in the remote, not the fan, because of what is occuring. I am now questioning that assumption. Is it possible that when I reprogram the remote the fan is able to read the signal and then soon forgets the remote's language?


    kaseki, I'm wondering if you know more about my fan then the company does! I have not looked on e-bay for a fan assembly. Is that the whole new fan or just the internal workings? When I looked earlier I found 2 totally NIB same fans as mine. I will check on it. My spouse just wants to get a new fan, but I love this fan and want to get it functioning again if it doesn't cost more than a new fan.

  • 4 years ago

    [reverse commentary] I can't evaluate relative costs, but in any action user time has some value that you might want to include. I have (maybe "had" is a better verb) enough room for spares in various cases, and in this case I would definitely get another fan assembly. Then try its remote first (following setup directions). If that doesn't work, then I would definitely suspect the fan itself, and replace it. This may be a pain depending on fan height, weight, need to balance new blades, etc.

    If the remote display fails intermittently, then the remote likely has a problem no matter what the fan's problems might be. Maybe a cold solder joint, dirt, corroded battery terminals, ... ; the list might be quite long. I can only guess, though, from this distance.

    Good luck!