Software
Houzz Logo Print
andrea_bowen78

Copper Range Hood — budget, cleaning, size

4 years ago

ISO budget copper range hood (trying to keep total cost including components under $4000)
Anyone know anything about the SINDA brand? Or any other brand suggestions?
How hard is copper to maintain? I’m alright with some wear/tear/character.
30” range with 36” of space between the upper cabinets above. Should I go for 30” hood with 3” space in either side, or try to squeeze in a 36”?

Thanks!

Comments (11)

  • PRO
    4 years ago
    last modified: 4 years ago

    Your budget figure is about a third of the dollar minimum that is needed for quality components. Just the insert components end up being around 4K.


    Copper is a living finish. It will age with all different color aspects to it, depending on the impurities, what touches it, and if the kitchen is actually used for cooking. Knockoff brands with impurities age badly, with unpredictable tarnishing. It’s even worse if it is clear coated. Those tend to peel.


    A high quality material will still require regular polishing if you want to maintain the new and shiny look. It can only be cleaned with non acidic pH neutral cleaners if you want it to age and turn brown. It is difficult to maintain an even colored finish when cleaning regularly, so its best to embrace a partially shiny, partially different colors of brown look.

  • 4 years ago
    last modified: 4 years ago

    I have a copper hood in a different style.

    My hood has been installed for about 4 years and still looks great. It isn't a natural finish but has a dark factory finish.

    I have a lot of copper components in my kitchen and they have different finishes and were sourced from different manufacturers.

    I don't know anything about your brand. A copper hood (or anything other than an off the shelf hood) is going to be a more expensive option. Depending on style they can be off the charts expensive or moderately expensive. My hood and insert weren't nearly $4000 although they were purchased prior to the pandemic.

    My hood is from Premier and my designer got a great price from them. You can check them out as the quality is very good - I can vouch for that. My hood was more or less custom beccause it was constructed after I purchased the insert. That is something to keep in mind since you purchase the insert first and supply those specifications to the hood manufacturer who makes a hood that is compatible with your insert


    Premier Copper Hood


    My kitchen sink has a living patina unlike the hood and is from Havens Metal. They make extremely high quality stuff but their prices are much higher than Premier but I wanted that kind of quality in my kitchen sink unlike the copper hood which was aesthetic rather than functional - the insert is of course functional but I got a highly rated insert


    Havens does custom hoods


    Havens Metal Hoods

  • 4 years ago
    last modified: 4 years ago

    You need a 36”W x27”Dx 42” H hood mounted 66” AFF in a 48” open space between cabinets , if you want a hood like that. 108” ceiling at a minimum.

    A focal point hood like that with all of those flourishes needs a lot of negative space around or it just looks like a bad squinched up mistake. You also need a minimum 600 CFM blower, plus a code required make up air system. This is a luxury design choice, and you need a luxury budget to accomplish it. By the time you add the blower, larger ductwork, MUA system, and labor, your budget is 1/5 to 1/6 of the total needed.

  • 4 years ago

    See also https://www.handcraftedmetal.com/, makers of my favorite example of serious hood construction:



  • 4 years ago

    @Verbo — so what you’re saying is, “go big or go home”? Can I not have a small simple copper hood since I need ventilation anyway? We don’t need a work of art in our kitchen, just want a functioning piece that is not industrial stainless steel or boring painted wood.

  • 4 years ago

    I think Verbo tends to over complicate rhings and quote super high costs


    My copper hood is just a hood with an insert like any other hood with an insert but it is copper exterior instead of wood. It isn’t industrial strength or larger than other materials would have been 🤷‍♀️ I don’t have a professional range and I don’t have a restaurant strength hood either


  • 4 years ago

    If you give up the curves and flourishes pictured, and do a plain box hood, then you can have it integrate and touch the other cabinets without any negative space around it.


    At that point, it isn’t a feature. It’s a poorly integrated lonesome accent.


    You might as well do a plain 24” deep cabinet and just DIY do a band of copper at the bottom as an accent. That copper needs to be repeated elsewhere in the room, as it is no longer the grand statement focal point with all of the open space around it to emphasize it as that.



  • 4 years ago

    I won't address aesthetics, but a hood large enough for full capture and "powerful" enough for full containment is needed to meet the primary functions of a cooking ventilation hood -- removal of cooking effluent to the outside. The hood is not primarily intended for kitchen air changes.

    Capture requires hood entry aperture overlap of the expanding plumes generated by the pans (and gas combustion products if present). This requires significant hood size. Containment requires that the effluent that is captured is passed through the grease collecting and fire stopping baffles and brought to the outside via ducting. This requires a significant air flow rate (CFM) to avoid having captured effluent reflect out of the hood. And to achieve the required CFM without back-drafting other combustion appliances (if present) or sucking air through cracks in the wall requires a make-up air system.

    The OP should read the extensive material here on hood and MUA requirements and then decide how to trade-off performance, cost, and aesthetics, keeping in mind that without performance, the hood is only decorative.

  • 4 years ago

    Thanks for all of the helpful advice so far! It certainly gives me a lot to think about. I had considered ventilation for a 30" range to be fairly straightforward, but it seems maybe not? In any case, I included a photo in my original post as an example, I'm not married to this particular hood or design (although it is really basic for a copper hood, I don't know why everyone thinks it is so fancy looking, lol), but here is a link to that actual hood, and it is on budget https://www.sindacopper.com/products/classic-copper-range-hood-h3

    -- mainly wondering if this brand (SINDA) is alright or garbage, or if there is a good mid-range, mid-budget company out there that makes something simple and decent. I don't want artisan or customized. I wanted to go higher end than what Zline offers (their price range is $1300-$2300 for copper). I'm okay if it's not 100% copper, and having copper laid over stainless steel. To me, that seems at least a little better than Hoodsly, for example, which is wood veneer over plywood.

    Thanks again! I'm really grateful to have some pros weighing in!

  • 4 years ago

    Thanks again Louis! I didn’t even think to look up their corporate headquarters, that is hilarious!

  • 4 years ago

    @Andrea Bowen


    I understand your question about the quality of the hood from Sinda as you would be purchase the exterior decorative hood AND the interior mechanical section.


    When people opt for a "designer" style hood whether it is copper, wood or some other kind of non-standard type, the exterior hood and the interior "fan/blower" are purchased separately unlike the more common hoods in which you purchase an "integrated" hood and the price is inclusive.


    For example, my hood has a copper exterior which is the portion you see and I bought the hood insert separately. I checked ratings and quality just as one would do for any purchase. FWIW my insert is from Zephyr and was well rated and revewed and recommended when I purchased it. Mine has the recomended "strength"; came from a reliable brand and had some features I liked including easier to clean system and a remote control. It has been awhile since I researched hoods but as I recall there were several kinds of systems which are cleaned differently and some were more difficult to access and take off.


    There really isn't much that can go wrong with the exterior copper hood because it isn't mechanical. You send the specifications of the insert to the company and they fabricate the hood so that the insert will fit and work when they are both installed on the wall.


    As I original posted my copper hood is from Premier Copper which is a company which makes their products in the USA and is well priced. However going this route is not a "budget" choice because the two components are each more than a "standard" stainless hood and I suspect that installation costs a bit more. I bought prior to the pandemic so pricing probably has gone up since then and I can't recall what I paid but the comparable Zephyr insert is now about $1400 which is just for the insert - that is more than the cost of the hood you are thinking about which includes the "hood" and the insert/blower mechanical system. Probably in today's prices, my system would be about $3000 total but you can check with Premier in terms of what they charge for a copper hood tomorrow. Their quality is good and their pricing is lower than other places.

    Andrea Bowen thanked Helen