Software
Houzz Logo Print
kristinrae56

Pulls - one or two on 36" doors

3 years ago
last modified: 3 years ago

For people who have a lot of 36" doors in kitchen - one pull or two? I have been told that one pull will put more stress on the door. Two pulls at 4 or 5 inches? Assume one would be much longer.....

Comments (20)

  • 3 years ago
    last modified: 3 years ago

    One larger pull for 36” drawers, puts no real stress on the drawer, as the weight is evenly distributed. They’re also easier to use, better ergonomically for people as they age. One pull can easily be opened with one finger, if your hands are gunky.

    The folks who have two pulls, but often just use one, are actually stressing the drawer, as the drawer can open unevenly.

    Those are 36” pots and pans drawers under the range top.

  • 3 years ago

    I vastly prefere two ~ 5" pulls on 36" doors, finding those single, long (12"+?) pulls both unaesthetic and hard to use. But, I'm a bit old-fashioned (not to mention old) and also open drawers using both pulls...

  • 3 years ago

    I also prefer one longer pull on a larger drawer.

    My 34" drawers have a 9-3/16" pull.

    My 42" drawers have a 12-1/2" pull.

    The rest of my drawers have a 7-9/16" pull.

    I don't just go by size of the drawer, but also depends on what other drawers/doors are around it and the overall balance when looked at as a whole.

  • 3 years ago

    I love my singe 12” pull on 36” drawers. Easy to open with 1 hand and I feel much more please to eye than the double.

  • 3 years ago

    I put 2 pulls on my 34" drawers, because I had 2 drawers at the top, and I thought it looked better to have all the pulls lined up. (in hindsight, I should have made the top drawer just one, and used dividers, but too late now).


    We lived there almost 8 years, and never had issues opening those drawers with one pull. We had Blum drawer glides.

  • 3 years ago
    last modified: 3 years ago

    Your OP says mentions doors three times, but are you talking about drawers? I've not heard of two pulls on doors.

    If you meant drawers, I do not like two pulls on a drawer regardless of drawer width. It will be twice the cost of one pull, and also people tend to use just one of the two pulls, causing the one that is most used to be loose and also the drawer can rack over time by being pulled just on one side.

    The rough rule of thumb is 1/3 the width of the drawer for aesthetic balance. So your 36" drawer (if you meant drawer) should have a 12" pull. While that sounds large, visually it looks good. What you should do is make aluminum foil templates in the pull sizes you are considering, and hold them up against the drawer. Do that with the doors you asked about as well. If you don't have the drawers and doors yet, take cardboard shipping boxes, open them up, and cut them into the size of the doors and drawers and tape them to the wall. Then hold up your aluminum foil pulls against them.

  • 3 years ago

    That is a great idea to spec it out. No we don't have the cabinets yet. I meant drawers, yes....There are mostly lower drawers no uppers - and a couple of towers. The cabinets are in Farrow and Ball very dark green paint and the towers are white oak. I get the one handle point of view - my kitchen look is "DeVol" ripoff and they always seem to use two handles or cabinet cups or those little knobs but I need function over form.

  • 3 years ago

    By the way, from way earlier (5 years) HOUZZ posts on hardware I found two good sites - Forge Hardware Studio and Yesterhome....both doing brass and way way less expensive than the DeVols, Armac Martin, Classic Brass et al

  • 3 years ago

    I have 2 pulls. Just personal preference.

  • 3 years ago

    It's actually cheaper, with Top Knob's pricing, to use, for example, two 5 1/16" Riverside pulls @ $14.40 ea. ($28.80 total) rather than buy a single 12" pull in the same style @ $42.50 ea. (savings of $13.70 per drawer). Ditto, picking randomly, a Podium style in polished chrome @ $16.90 ea. for two 5 1/16" ($33.80 total) versus a single 12" pull, same style, @ $57.70 ea. (savings of $23.90 per drawer). Twenty+ years of using 36" drawers with just two knobs never "racked" any of them in our old kitchen. The new cabinet drawers being installed this very moment will each have two pulls because, to us, that scheme fits better with the style of the new kitchen.

  • 3 years ago

    I also went with a single 12” pull for 36” wide drawers and have been very happy. We used to have smaller double pulls on wide drawers and after 20 yrs those drawers had become wobbly from being opened primarily using one pull, so I didn’t want a repeat of that.

  • 3 years ago

    And yea the longer pulls were slightly more $$ than two short ones, even for pulls from HD. But I still love them.

  • 3 years ago

    We have 27" drawers with one and 33" drawers with two. I don't think it makes much difference--we decided based on aesthetics (the 27" is in a bank of full-width drawers, while the 33" is in a bank where the top drawer is split into two smaller drawers, so the pulls all line up that way). I think any stress a single pull might put on the slides is balanced out by the many people who will open the two-pull drawer by pulling on just one handle (but maybe that's just my family!) I wouldn't worry about that as a factor either way.

  • 3 years ago

    You could also mix pulls and knobs. It is what I am seeing with the high-end designers.







  • 3 years ago

    Isn't that how most people have done it until recently, when it became much more popular to do pulls on doors? I did pulls on drawers and knobs on doors. I can call myself a high-end designer! ;-)

    Although I did get a bit influenced by the recent use of pulls on doors and did a few pulls on the doors of some of my built-ins.

  • 3 years ago
    last modified: 3 years ago

    @chispa not sure...in our kitchen when I was growing up (I do not want to say how long ago that was, but it was a long time ago haha), we had pulls. Then I feel like starting in the 80s-'90s when it was all knobs for the next 20-25 years, and then pulls returned. I mentioned high-end designers because I have rarely seen on this forum, or Pinterest, etc. that "regular people" today are doing the combo of pulls/knobs. The kitchens I posted above are very expensive designs.

  • 3 years ago

    Great to see those pictures

  • 3 years ago

    I just have single knobs everywhere, even on my largest drawers where I meant to do two and somehow forgot and drilled for one. Works fine and these are even bigger than 36" wide (and 30" front to back) (and containing a good complement of cast iron pans).


    It might look weird but it turns out nobody cares.

  • 3 years ago

    When we had our kitchen renovated a few years ago, I chose Top Knob pulls size 5 & 1/16”. I am still quite happy with my choice of pulls!

  • 3 years ago

    I went looking at old photos of previous houses we owned. Didn't find any of house #1, but found a kitchen shot of house #2 and the people who built it put knobs on drawers and pulls on doors, the opposite of what I would do ... it didn't cause me any harm to live with that arrangement for the 3 years we lived there! lol

Sponsored
AIS Renovations
Average rating: 4.5 out of 5 stars15 Reviews
Custom Craftsmanship & Construction Solutions in Franklin County, Ohio