Software
Houzz Logo Print
lmnjp

New Fiberon Sanctuary deck

6 days ago

Just extended an existing Fiberon deck.After a heavy rain, the new part of the deck had a signicant amount of water that puddled. The sun doesn’t hit the deck until later in the day during the winter here and most of the water eventually evaporated or drained but there were several boards with standing water for close to 24 hours. Waiting to hear from the company who built the deck.

Also, I am finding conflicting information on the internet about spacing between boards for the Sanctuary deck. The gap between the new deckboads are spaced closer than the original deck boards. It was probably in the 50’s the day the new boards were laid. I have found conflicting information on the spacing for the ambient temperature that day from 2/16’ to 3/8.’ Most of the boards are 3/16’ but there re several that are 2/16 “ I have read that the spacing cn range from 1/4” to 3/16.”

Could this inconsistent spacing result in excessive puddling and bending?

Should the deck have a slight pitch?

Would this inconsistent spacing void the warranty?

Thanks to anyone who cn shed light on this issue or if this normal a call to Fiberon customer service said there are no coatings or finish on the boards.

Comments (10)

  • 6 days ago

    Minimum spacing between boards should be 3/16" in. according to the manufacturer.


    I've only used p.t. wood and provide a slope to the front or to one side.

  • 6 days ago

    Any deck should have a slope or pitch built into it. The gaps side to side are paramount for expansion and contraction, especially with composite. Spacers or the attachment clips shoudl most definitely be used.

  • PRO
    5 days ago

    X3, what was said above: check the spacing between boards and check the deck framing to make sure there is a min 1/8" pitch per foot on the framing for runoff, and also make sure the installation was done to specs.

    Another cause could be the decking itself, on some composites if they were improperly stored or manufacturers defect, you will see that the center of the board have a low point (you will notice a crown) and that is the reason for water collecting there. Some installers, especially if they're Fiberon certified, will notice it and order a replacement, but if the installer is not certified, most will ignore it and install it anyway.

    On a general note "Fiberon Sanctuary" is a capped composite, meaning any minor dips in framing joists, not pitch, or decking itself is gonna hold standing water instead of letting it runoff.

    That said, make sure the installer checks everything and takes care of it while still under installation warranty, because if the installation is incorrect, there's a good chance you will lose material warranty down the road, and this is the 1st thing they will be looking at.

    Good luck


  • 5 days ago

    In additon to GN Builders notes above, what was the joist spacing? Hopefully 12" OC which is very important for composite decking, especially capped products as composite does not have much strength or structural integrity, so needs to be very well supported.

  • 5 days ago

    Contractor left a message indicating “I did talk to the supplier. I was correct. They spray a film on the boards to protect them during shipping and everything. They said it would wear off after time. Also said you might see some superficial scratches that will disappear after time”

    Do suppliers typically spray a film? Acceptable practice? Will it void the warranty? No luck reaching Fiberon customer service. And what if this doesn’t wear off eventually we want to pay the contractor but at the same time we need to protect ourselves what if this film doesn’t wear off in a couple weeks it a couple months, then what?

    The extensive puddling/ ponding on several boards that remained nearly 18-24 hours after the heavy rains and after much of the deck boards beading, had evaporated or dried up, is that typical?

  • PRO
    5 days ago

    I never heard about any spray being applied to decking for protection.

    Fiberon Sanctuary decking and other capped decking, like Trex Transent, are already designed with a cap layer, which is applied to 3 sides of the board, and this is the intended protection against marring, fading, and staining.

  • 5 days ago

    Would the water breading and pooling be a result of capped decking!

  • PRO
    5 days ago

    Capped decking will not absorb water, so it's normal for the water to be beading on the surface; that is normal... Picture the hood of the car, even with the slope; the water will bead on it, but it will not puddle.

    When you have water puddling on the surface, that becomes an issue it could be crowned decking board, which is a defect; it could be a low spot or a lack of slope...

    Deck drainage depends on having overall slope, min 1/8 per foot, so the water drains between the decking boards, which must be free of debris, etc.

    I mean, it's easy to see what the issue is in that area; you don't see beading on it, you see standing water (that's what it looks like in that picture), which is not normal. Just check the boards, put a level on the deck, and see if the joists were never crowned properly and created a low spot.

    The homeowner should call Fiberon or the place the material came from, and they will send a local representative to evaluate the issue, and you will know exactly what it is.



  • 5 days ago
    last modified: 5 days ago

    " I never heard about any spray being applied to decking for protection. "

    Definitely never heard of such a thing or what the substance would even be. I wonder how this "protectant" would affect the Fiberon warranty and how they feel about it. My issue now is the contractor is obviously BS'ing you which leads me to believe you will shortly be on your own.

  • 10 hours ago

    Latest response.

    Good afternoon. I talked to the Fypon rep. He kinda told me the same thing. Said it’s like looking at a waxed car and a non waxed end car. The waxed car repels. He did send me a link to the warranty company that will work with you. Please reach out to them to settle this issue. I don’t feel this is something I did. I just installed what you asked for. “

    There’s more to this than he just installed what I asked for. The comparison to a waxed and unwaxed car doesn’t fully address our concerns. We are seeing standing water and puddling on portions of the new decking that we are not seeing on the original Fiberon decking. We would like to understand why this is happening and whether it indicates a product issue, an installation issue, or something else.

    We intend to contact Fiberon directly and request that an authorized representative review the situation, including the installation, and advise us whether the work complies with the manufacturer’s specifications and warranty requirements.

    We would also like written confirmation that the deck was installed in accordance with those requirements. We think that’s a reasonable step before treating this solely as a warranty claim.

    Thoughts?