Hammered Iron Balusters - Finished in Gun Metal Patina. Stairwell remodel in Maple and Iron.
Example of a trendy staircase design in Grand Rapids

Inspiration for a timeless staircase remodel in Chicago

Titan Architectural Products, LLC dba Titan Stairs of Utah
Example of a large classic wooden curved open staircase design in Salt Lake City with yellow walls

House of Forgings Aalto Collection featuring the large single rectangles (16.6.3), 3 square panels (16.6.5) and plain bars (16.2.1), available in satin black and ash gray.

The view of the sunset from this breathtaking Cat Mountain composite deck. Designed & built by Jim Odom at Archadeck Austin. Photo Credit: Kristian Alveo & TimberTown

Nina Phillips
Inspiration for a large timeless wooden curved open and mixed material railing staircase remodel in DC Metro with beige walls

Classic Round Aluminum Balusters By Deckorators

Mega Series Square Iron Balusters By Fortress

Titan Architectural Products, LLC dba Titan Stairs of Utah
Staircase - large traditional carpeted curved staircase idea in Salt Lake City with carpeted risers

Stairways that have a baluster add beauty to a home. However, if the baluster is broken, then this can cause the stairs to look bad. Fortunately, it is not that difficult to replace a broken baluster. Below are some of the steps you will need to take: Remove The End Cap It is important to be very careful when you are replacing the baluster. You will need to keep the baluster intact so that a wood turner will be able to make an exact copy of it. You will most likely need to remove the end cap from the stairs. Break the seal that is between the tread and the end cap using a sturdy knife or pry bar. Breaking The Baluster If you do not want to salvage the baluster, then you do have other options. You can use a hammer to loosen the nails at the top of the baluster. Make sure that you do not damage the adjacent balusters or handrail. You can use your hands to loosen the bottom half of the baluster. Make sure you use gentle force. Create A New Baluster Unless you are fortunate enough to have the same baluster at a local home center, you are going to need a wood turner to make a new baluster. Make sure you tell your wood turner the specific type of wood you need. If you are not concerned about the original color, then you will need to select the wood that is the hardest. Ask the wood turner to leave the spindles intact. This may make it harder for you to fit the baluster into the staircase. However, this reduces the chances of getting a misfit from the wood turner. Prepare The Stairs It will likely take one or two weeks to turn a baluster. You can prepare the stairs during this time. Clean up the area around the stairs. Put the end cap back on the stair tread. Measure the tread to where the new baluster and handrail will meet on the upstairs side. Prepare The Baluster You can prepare the baluster by sanding it smooth. Measure from the bottom of the baluster to the bottom of the tenon joint. Cut the top end of the baluster so that it matches the handrail's slope. Hold a T-Bevel against the handrail's underside where the new baluster will go. Mark the angle with a pencil. Install The Bottom Of The Baluster Insert the tenon inside of the mortise. After that, position the top of it in the middle of the handrail's underside. Install The Top Of The Baluster Make sure the tenon is straight by using a carpenter's level. Have someone hold it in place in order to ensure that it matches the angle of the other balusters. Place one nail into the baluster's upstairs side. You most likely will not need more than two finishing nails. Remove dust by wiping off the baluster. Use painter's tape to mask off the handrail and stair tread. Stain or paint the new baluster. Since this project involves a lot of work, you can save a lot of time and stress by contacting House Doctors to help. Thanks to our highly experienced team, you can depend on us to get the work done promptly and properly. by Ken Benedetto, Owner of House Doctors of Scotch Plains - Fanwood

Lomonaco's Iron Concepts
Example of a classic staircase design in Philadelphia

Queen Elizabeth Cellular PVC/Vinyl Sawn Balusters and Cellular Vinyl Chesapeake Spandrel by Durabrac
This is an example of a traditional porch design in Miami.

Single basket and double basket twisted iron balusters.

Staircase - traditional staircase idea in DC Metro

Example of a mid-sized classic backyard deck design in Baltimore with no cover

Inspiration for a large industrial wooden u-shaped metal railing staircase remodel in Chicago with painted risers

This simple contemporary style home from Addison's Wonderland features Aalto Collection balusters in the Satin Black finish from House of Forgings. Photographs from Addison's Wonderland: http://addisonswonderland.com/staircase-balusters-heaven/

Mega Series Square Iron Balusters By Fortress

Elegant staircase photo in Chicago