This Project consisted of lifting the existing bricks and storing them on site, remove a portion of the existing brick walls and remove wall caps, install new flagstone wall caps to provide 1″ overhang on each side, pressure wash sitting walls, excavate the existing patio stone dust base and discard of it, excavate patio to proper base depth of 8″+- and install a proper 2A Modified stone base. We then installed a 1″ sand setting bed and reinstalled the existing brick pavers. The new installation also included drainage pipe and catches to allow water to escape the patio and drain beyond the foot print of the patio, house and shed. Also included were removal the existing upper flagstone patio and walking path, leveling the path and lay larger pieces of flagstone in the upper patio. We will also install proper joint material between the flagstone for a more uniform walking surface. We also used the existing flagstone to make small garden paths in place of the brick paths. Lastly, included was grading a small swale in the back lawn to divert water around to the sides of the house and away from the rear patio area. A drainage system along the right side of the shed to collect ground water as well as downspouts along that side of the shed and carport and move the water to the street through 4″ solid drainage pipes was also installed.

This Project consisted of lifting the existing bricks and storing them on site, remove a portion of the existing brick walls and remove wall caps, install new flagstone wall caps to provide 1″ overhang on each side, pressure wash sitting walls, excavate the existing patio stone dust base and discard of it, excavate patio to proper base depth of 8″+- and install a proper 2A Modified stone base. We then installed a 1″ sand setting bed and reinstalled the existing brick pavers. The new installation also included drainage pipe and catches to allow water to escape the patio and drain beyond the foot print of the patio, house and shed. Also included were removal the existing upper flagstone patio and walking path, leveling the path and lay larger pieces of flagstone in the upper patio. We will also install proper joint material between the flagstone for a more uniform walking surface. We also used the existing flagstone to make small garden paths in place of the brick paths. Lastly, included was grading a small swale in the back lawn to divert water around to the sides of the house and away from the rear patio area. A drainage system along the right side of the shed to collect ground water as well as downspouts along that side of the shed and carport and move the water to the street through 4″ solid drainage pipes was also installed.

This Project consisted of lifting the existing bricks and storing them on site, remove a portion of the existing brick walls and remove wall caps, install new flagstone wall caps to provide 1″ overhang on each side, pressure wash sitting walls, excavate the existing patio stone dust base and discard of it, excavate patio to proper base depth of 8″+- and install a proper 2A Modified stone base. We then installed a 1″ sand setting bed and reinstalled the existing brick pavers. The new installation also included drainage pipe and catches to allow water to escape the patio and drain beyond the foot print of the patio, house and shed. Also included were removal the existing upper flagstone patio and walking path, leveling the path and lay larger pieces of flagstone in the upper patio. We will also install proper joint material between the flagstone for a more uniform walking surface. We also used the existing flagstone to make small garden paths in place of the brick paths. Lastly, included was grading a small swale in the back lawn to divert water around to the sides of the house and away from the rear patio area. A drainage system along the right side of the shed to collect ground water as well as downspouts along that side of the shed and carport and move the water to the street through 4″ solid drainage pipes was also installed.

This Project consisted of lifting the existing bricks and storing them on site, remove a portion of the existing brick walls and remove wall caps, install new flagstone wall caps to provide 1″ overhang on each side, pressure wash sitting walls, excavate the existing patio stone dust base and discard of it, excavate patio to proper base depth of 8″+- and install a proper 2A Modified stone base. We then installed a 1″ sand setting bed and reinstalled the existing brick pavers. The new installation also included drainage pipe and catches to allow water to escape the patio and drain beyond the foot print of the patio, house and shed. Also included were removal the existing upper flagstone patio and walking path, leveling the path and lay larger pieces of flagstone in the upper patio. We will also install proper joint material between the flagstone for a more uniform walking surface. We also used the existing flagstone to make small garden paths in place of the brick paths. Lastly, included was grading a small swale in the back lawn to divert water around to the sides of the house and away from the rear patio area. A drainage system along the right side of the shed to collect ground water as well as downspouts along that side of the shed and carport and move the water to the street through 4″ solid drainage pipes was also installed.

This Project consisted of lifting the existing bricks and storing them on site, remove a portion of the existing brick walls and remove wall caps, install new flagstone wall caps to provide 1″ overhang on each side, pressure wash sitting walls, excavate the existing patio stone dust base and discard of it, excavate patio to proper base depth of 8″+- and install a proper 2A Modified stone base. We then installed a 1″ sand setting bed and reinstalled the existing brick pavers. The new installation also included drainage pipe and catches to allow water to escape the patio and drain beyond the foot print of the patio, house and shed. Also included were removal the existing upper flagstone patio and walking path, leveling the path and lay larger pieces of flagstone in the upper patio. We will also install proper joint material between the flagstone for a more uniform walking surface. We also used the existing flagstone to make small garden paths in place of the brick paths. Lastly, included was grading a small swale in the back lawn to divert water around to the sides of the house and away from the rear patio area. A drainage system along the right side of the shed to collect ground water as well as downspouts along that side of the shed and carport and move the water to the street through 4″ solid drainage pipes was also installed.

This Project consisted of lifting the existing bricks and storing them on site, remove a portion of the existing brick walls and remove wall caps, install new flagstone wall caps to provide 1″ overhang on each side, pressure wash sitting walls, excavate the existing patio stone dust base and discard of it, excavate patio to proper base depth of 8″+- and install a proper 2A Modified stone base. We then installed a 1″ sand setting bed and reinstalled the existing brick pavers. The new installation also included drainage pipe and catches to allow water to escape the patio and drain beyond the foot print of the patio, house and shed. Also included were removal the existing upper flagstone patio and walking path, leveling the path and lay larger pieces of flagstone in the upper patio. We will also install proper joint material between the flagstone for a more uniform walking surface. We also used the existing flagstone to make small garden paths in place of the brick paths. Lastly, included was grading a small swale in the back lawn to divert water around to the sides of the house and away from the rear patio area. A drainage system along the right side of the shed to collect ground water as well as downspouts along that side of the shed and carport and move the water to the street through 4″ solid drainage pipes was also installed.

This Project consisted of lifting the existing bricks and storing them on site, remove a portion of the existing brick walls and remove wall caps, install new flagstone wall caps to provide 1″ overhang on each side, pressure wash sitting walls, excavate the existing patio stone dust base and discard of it, excavate patio to proper base depth of 8″+- and install a proper 2A Modified stone base. We then installed a 1″ sand setting bed and reinstalled the existing brick pavers. The new installation also included drainage pipe and catches to allow water to escape the patio and drain beyond the foot print of the patio, house and shed. Also included were removal the existing upper flagstone patio and walking path, leveling the path and lay larger pieces of flagstone in the upper patio. We will also install proper joint material between the flagstone for a more uniform walking surface. We also used the existing flagstone to make small garden paths in place of the brick paths. Lastly, included was grading a small swale in the back lawn to divert water around to the sides of the house and away from the rear patio area. A drainage system along the right side of the shed to collect ground water as well as downspouts along that side of the shed and carport and move the water to the street through 4″ solid drainage pipes was also installed.

This Project consisted of lifting the existing bricks and storing them on site, remove a portion of the existing brick walls and remove wall caps, install new flagstone wall caps to provide 1″ overhang on each side, pressure wash sitting walls, excavate the existing patio stone dust base and discard of it, excavate patio to proper base depth of 8″+- and install a proper 2A Modified stone base. We then installed a 1″ sand setting bed and reinstalled the existing brick pavers. The new installation also included drainage pipe and catches to allow water to escape the patio and drain beyond the foot print of the patio, house and shed. Also included were removal the existing upper flagstone patio and walking path, leveling the path and lay larger pieces of flagstone in the upper patio. We will also install proper joint material between the flagstone for a more uniform walking surface. We also used the existing flagstone to make small garden paths in place of the brick paths. Lastly, included was grading a small swale in the back lawn to divert water around to the sides of the house and away from the rear patio area. A drainage system along the right side of the shed to collect ground water as well as downspouts along that side of the shed and carport and move the water to the street through 4″ solid drainage pipes was also installed.

This Project consisted of lifting the existing bricks and storing them on site, remove a portion of the existing brick walls and remove wall caps, install new flagstone wall caps to provide 1″ overhang on each side, pressure wash sitting walls, excavate the existing patio stone dust base and discard of it, excavate patio to proper base depth of 8″+- and install a proper 2A Modified stone base. We then installed a 1″ sand setting bed and reinstalled the existing brick pavers. The new installation also included drainage pipe and catches to allow water to escape the patio and drain beyond the foot print of the patio, house and shed. Also included were removal the existing upper flagstone patio and walking path, leveling the path and lay larger pieces of flagstone in the upper patio. We will also install proper joint material between the flagstone for a more uniform walking surface. We also used the existing flagstone to make small garden paths in place of the brick paths. Lastly, included was grading a small swale in the back lawn to divert water around to the sides of the house and away from the rear patio area. A drainage system along the right side of the shed to collect ground water as well as downspouts along that side of the shed and carport and move the water to the street through 4″ solid drainage pipes was also installed.

Becky Hulsey, Envision Virtual Tours The Lodge at Gold Mine Falls A Once in a Lifetime Opportunity Awaits…. Have you dreamed of owning your own spectacular waterfall, a serene trout pond, or a one of a kind mountain lodge filled with high end touches, all near Lake Burton? If the answer is yes…..then “The Lodge at Gold Mine Falls” is for you! Located just off HW 76 .3 miles to Anchorage Marina, this unique 2.8 acre property borders the National Forest, boasts a fully remodeled 3 bedroom, 3 bath, 2000+ square foot rock lodge that is adjacent to its own private, spectacular 60 foot waterfall all surrounded by native landscape such as rhododendron and mountain laurel. Tumbling under the 40 foot suspension bridge, the pristine, crystal clear water continues to ramble on its way to large pond ready to be stocked with trout. Picture yourself fly fishing for a trout dinner right at your front door, or delight your friends or family while entertaining on your new porch or extensive, multi-level deck that connects your new home to your own waterfall. The kids or grandkids will be entertained for hours wading in the pool at the base of the waterfall, exploring the crooks and crannies among the stream’s boulders while looking for salamanders, or panning for “fool’s gold” in the stream. Just imagine….The Lodge at Gold Mine Falls has all this and more! As you walk up the front steps to The Lodge at Gold Mine Falls, you will notice the craftsmanship of this uniquely one of a kind home made from local stone and granite from a period gone by. If you look closely at some of the stones, you will find raw garnets, some the size of a nail head. Upon opening the front door constructed of solid oak and a tasteful piece of leaded glass, you will be amazed at the spaciousness of the lodge room. Once upon a time, the 20 x 30 foot room with 10 foot ceilings was the entire home. The focal piece of the room is the new floor to ceiling field stone fireplace, hand honed solid maple mantel, rounded hearth, accentuated by a hand-cut keystone, and flanked by raw cedar columns. The new gas logs can be remotely controlled with programmable heat. A built-in floor to ceiling cherry wood wall unit, with granite serving surface, highlights a side wall and is topped off with a large piece of stained glass from an English pub. The mood lighting behind the stained glass and the antique library ladder really highlights this unique bookcase. Distinctive lighting fixtures and fans provide dining area lighting and circulation from the cool breezes off of Lake Burton. On the bottom, the solid oak 1.5 inch flooring is a remnant of the past on the top, the height of the ceilings is enhanced by double crown moldings throughout and a touch of the outdoors is brought indoors by the three new skylights. Surrounded by rustic cedar window boxes, additional ambient light streams through the four windows facing south, and the new French doors. As you open the French doors to the new porch, you are immediately struck by the sights and sound produced by the rushing water as it cascades over the spectacular multilevel waterfall. You will also notice that the mountain has literally been carved away as you view the layers and striations in the granite that surround the back of the porch. The peaked cathedral ceiling sports a glass apex and the bead board on the ceiling accentuated by the raw cedar plank framing and the five cedar trees used as cornerstones all bring the outdoors within your reach. The addition of “E-Z Breeze” vinyl windows along with the cast iron gas stove will allow you and your family to enjoy the beauty and continually changing scenery at The Lodge at Gold Mine Fall during all four seasons. Opening the Adirondack style door on the other side of the lodge room allows you to step into the Lodge’s addition built at a later date. The four foot wide hallway boasts stained glass light fixtures and an architectural feature from the new stairwell that divides the living and the bedroom spaces. Knowing that the east wall in the kitchen and study were once on the home’s exterior allowed us to investigate and reveal the true character of these walls by removing the two layers of drywall and 4 inches of plaster exposing a striking addition to both rooms…… beautiful granite rock walls. The hallway flows into the granite breakfast bar which fully complements the newly exposed granite wall. From the Viking SS refrigerator to gas Jenn Air ceramic cooktop and microwave the appliances are a chef’s delight. Lighting is a critical component in a gourmet kitchen and the light from the double window is enhanced by two spotlights over the cooking area, LED task lighting under the cabinets, mood lighting over the top cabinets, and four “Murano” hand blown glass pendant lights over the sink and bar area. Scoring points in the design category, the full wood “Thomasville” two tone glazed cabinets that are country white and palomino scream style and sophistication, and are accentuated by the cool copper glass backsplash and refined stainless steel hardware. The porcelain, two bowl farmhouse sink is large enough for your biggest pots while the stainless steel sink guards will protect it from scratches. The SS faucet is professional quality and the Insinkerator will help the chef in the house save time with instant 190 degree water. An eight foot long exposed cedar tree trunk hangs over the cooking area allowing the chef to hang his/her favorite utensils and pots or pans in full lodge style. And who wouldn’t crave a large walk in pantry with commercial grade slides that will up to 120 pounds. With all these features, the cook/cooks in the family will love spending time in this room. Across from the kitchen is a study/office area which can be closed off from the hallway by a double barn door. Except for the remarkable exposed granite rock wall mentioned earlier, the entire room has been paneled with raw cedar boards treated with Australian Tree Oil for true lodge feel. The triple crank out window provides a superb view of the pond and blazing Japanese maple trees in the fall. Outside, the hallway leads to the utility room which has been fully upgraded with all the modern amenities. The oak cabinetry with granite tops also has an extra deep sink with commercial kitchen sprayer. The sink area is surrounded by white subway tile while slate and green glass mini tile accents bring the outdoor colors inside. The doggy door, new exterior door and crank out window provide access to the back yard and additional light. From the new “Rinnai” point of use, gas hot water heater to the new “LG” full size, stackable washer and dryer, this utility room delivers. The master bedroom has four windows which provide outstanding light and air circulation. To take the chill off of nippy evenings, this bedroom also has its own romantic fireplace with travertine marble surround, remote controlled gas logs, and a beautiful antique oak and mirror mantle. To top it off, the en-suite bath contains high end fixtures, a spacious vanity, and floor to ceiling rain shower with independent valves allowing you to turn on the shower and not get wet. Multiple safety handrails and a fold down shower seat give bathers assurance and provide an additional measure of safety. The earthy color tiles, glass tile accents and hand blown light fixtures continue the lodge theme in this end of the house. Located across the hall, the guest bedroom is light and airy with its white window boxes and double crown molding, and also has an attached bathroom. This bathroom also has an entrance door leading to the hallway and doubles as the guest bathroom for the house. Its antique oak vanity and mirror, stained glass lights and wrought iron accents remind me of a past era while the vessel sink, modern fixtures, and floor to ceiling travertine and glass tile rain shower all bring the bathroom up to modern standards. Located at the end of the hallway, and next to the guest bathroom, is the handcrafted stairwell leading to the sleeping loft. The distinctive maple stair treads with their grain and raw edge being displayed, were milled locally in Clayton and then installed from underneath so that no screw or nail heads are visible. The staircase was completed with wrought iron spindles, raw cedar handrail and floor to ceiling end post. Upon your entry into the sleeping loft, you will notice the amount of light that enters through the two skylights and large window facing the pond. The sound of water rushing over the pond’s spillway is a delightful addition to this large sleeping loft. Finished with engineered hardwood flooring and two built in double beds with tree trunks for legs, the room can accommodate four additional twin beds. The sleeping loft is also equipped with a kitchenette and a distinctive cedar and rock walled bathroom. The bath features an antique dresser vanity with marble vessel sink, distinctive fixtures and a floor to ceiling polished travertine marble shower with rain head. This bathroom also has an exterior door leading to a secondary upstairs staircase in the back yard. Just envision the great sleepovers the kids or grandkids will have here or how your out of town friends or family will just love this special area designed with their comfort and needs in mind. Originally constructed in 1925 by “off Broadway” star Rose Grant, this property is rich in history. In the early years, this home was one of the first in Rabun County to generate its own electric from the waterfall. Several small cabins were also built on the property and rented out to guests who came for the waterfall, swim in the pond and connect with nature. Other notable residents were Mrs. and Doctor Fowler who was a local pediatrician. According to an aged newspaper article, Mrs. Fowler was very interested in the indigenous flora and fauna and grew a variety of native plants on the property including some that were rare or endangered. Many metal name tags still remain along the various paths on the property thus reminding you of times gone by and the true beauty of property. Lastly, this solidly built home has just been structurally solidified, become more energy efficient, and reconfigured to further usable space all while retaining the Lodge’s original charm. After removing the flooring in the kitchen, hall and both bathrooms, the home’s structure and roof were fortified with numerous concrete footers to support both bathrooms, kitchen, and stairwell walls that extend from floor to roof. To make this home more comfortable, energy efficient, and bring it up to modern standards, the electrical system was upgraded to 220 service with the wiring, outlets, electrical panels and fixtures replaced throughout the entire home. A whole house surge protector was also installed to protect against damage that may occur with lightning strikes. Speaking of electric…..the pond’s newly poured formed concrete wall contains a pipe enabling you to install your own hydro-electric system. And whether you might decide to tie into the grid or store you energy in a battery system, you could generate your own electric 24/7. The homes plumbing was also replaced with new pipes, energy/water efficient fixtures in each bathroom (including three Toto toilets), and a new cistern was installed behind the garage with a laboratory grade water filtration system. The task of water heating was completed by a gas Rinnai point of use hot water heater in the utility room and all windows were replaced with Anderson thermal pane and 6 Velux skylights were mounted to bring the outdoors inside. The home’s HVAC system was top of the line several years ago and both sets of new gas logs are controlled with remotes. Formerly a summer home, all exterior walls were studded out with insulation added, and whole house fans were installed in the attic and upstairs bathroom. Although many of these upgrades may not be visible, they allow the home to be more energy efficient and more comfortable……allowing The Lodge at Gold Mine Falls to become your four season retreat.

PipingProjects.eu is one of the leading Steel Pipe Manufacturers in Europe. Steel, a very resilient and versatile metal alloy mostly made of iron and carbon with varying amounts of manganese, nickel, chromium, and molybdenum added, is frequently used to make cylindrical tubes, usually referred to as Steel Pipe.  Steel Pipe Manufacturer are used widely in many different industries and applications because of its amazing strength, durability, and versatility. They are made to transfer fluids, gasses, and solids. In Europe, we are a reputable supplier of Steel Pipe Suppliers. Our state-of-the-art production facilities employ state-of-the-art technology to meet stringent industry standards, providing reliable performance under different situations. Our Steel Pipe Suppliers in India are not only long-lasting but also smoothly attached, which facilitates installation and lowers the possibility of leaks. In fluid transport systems, the smooth inner surfaces of the pipes promote operational efficiency, minimize friction, and enhance fluid flow.

Other Product: Steel Plate Manufacturer in Europe

The SW-141L is the larger sized round freestanding bathtub in its series with a modern circular and curved design. All of our bathtubs are made of a durable solid white stone resin composite and available in either a matte or glossy finish. This tub combines elegance, durability, and convenience with its high quality construction and chic modern design. This symmetrical, round, and curved designed freestanding tub will surely be the center of attention and will add a modern and contemporary feel to your new bathroom. Its height from drain to overflow will give plenty of space for any individual to enjoy a soothing and comfortable relaxing bathtub experience. The SW-141L has a smooth and rounded inner rim. This bathtub can fit two people comfortably. Item #: SW-141L Product Size (inches): 59.1 x 59.1 x 21.7 inches Material: Solid Surface/Stone Resin Color / Finish: Matte White (Glossy Optional) Product Weight: 418.8 lbs Water Capacity: ~86 Gallons FEATURES This bathtub comes with: A complimentary pop-up drain (Does NOT include any additional piping). All of our bathtubs come equipped with an overflow. The overflow is built integral to the body of the bathtub and leads down to the drain assembly (provided for free). There is only one rough-in waste pipe necessary to drain both the overflow and drain assembly (no visible piping). Please ensure that all of the seals are tightened properly to prevent leaks before completing installation. If you require an easier installation for our freestanding bathtubs, look into purchasing the Bathtub Rough-In Drain Kit for Free Standing Bathtubs.

Scott Sandler
Pool fountain - large contemporary backyard custom-shaped and concrete paver infinity pool fountain idea in Phoenix

The SW-131L is a large sized oval freestanding and symmetrical modern type bathtub. It is designed to look unique and simple, yet stylish. All of our bathtubs are made of durable white stone resin composite and available in a matte or glossy finish. Its height from drain to overflow will give plenty of space for two individuals to enjoy a comfortable relaxing bathtub experience. This tub combines elegance, durability, and convenience with its high-quality construction and chic modern design. This sophisticated oval designed freestanding tub will surely be the center of attention and will add a contemporary feel to your new bathroom. The SW-131L is a two-person bathtub and will be a great addition to a bathroom design that will transition in the future. Item#: SW-131L Product Size (inches): 70.9 L x 35.4 W x 24.4 H inches Material: Solid Surface/Stone Resin Color / Finish: Matte White (Glossy Optional) Product Weight: 352.7 lbs Water Capacity: 108 Gallons Drain to Overflow: ~16 Inches FEATURES This bathtub comes with: A complimentary pop-up drain (Does NOT include any additional piping). All of our bathtubs come equipped with an overflow. The overflow is built integral to the body of the bathtub and leads down to the drain assembly (provided for free). There is only one rough-in waste pipe necessary to drain both the overflow and drain assembly (no visible piping). Please ensure that all of the seals are tightened properly to prevent leaks before completing the installation. If you require an easier installation for our freestanding bathtubs, look into purchasing the Bathtub Rough-In Drain Kit for Free Standing Bathtubs.

French drain installation for foundation and yard drainage in Delmar, NY. Black perforated corrugated pipe laid in excavated trench with soil backfill and native vegetation.

This is an example of a traditional landscaping in Vancouver.

White Damask Kohler Tailored Vanity with chrome Kelston faucet. Nothing adds elegance to a bathroom like a furniture-style bathroom cabinet. Especially when they’re available in a huge range of sizes and every wood finish you can imagine.

  Morning routines shouldn’t involve a traffic jam at the sink. The 2025 Houzz Bathroom Trends Study found that 65 percent of U.S. renovators now choose a double-sink vanity to skip the wait. Designers agree: Titan Builders dubbed 2025 “the year of bigger, storage-packed double vanities,” forecasting dual-basin setups in family, guest, and even powder baths. As KBIS 2025 launches land, prototypes for 2026 layer in spa-grade wood, built-in outlets, and planet-friendly finishes. In this guide, we rank six standout models and show you how to size, install, and enjoy a clutter-free, two-sink future.   Methodology and selection criteria   A well-planned double-sink vanity keeps busy morning routines calm and clutter-free.   Before we crowned any winners, we mapped the entire 2024–2026 double-sink (dual-basin) market. That meant parsing KBIS exhibitor releases, scraping bestseller lists from Home Depot, Lowe’s, and Wayfair, and reviewing designer short lists in trade magazines. The sweep produced 110 candidate vanities, giving us visibility into every style, price tier, and material in play.   We then scored each model against six weighted factors that continue to matter long after installers leave:  

1. Build quality – 25 percent.Solid hardwood frames, dovetail drawers, and furniture-grade plywood backs, never particleboard in disguise.  
2. Design versatility – 20 percent.Lines and finishes that suit modern, classic, or farmhouse baths without dating quickly.  
3. Sustainability – 15 percent.FSC-certified wood, CARB 2 compliance, and low-VOC finishes for healthier air.  
4. Storage efficiency – 15 percent.Deep drawers, tilt-outs, or power cubbies that corral countertop clutter.  
5. Value for money – 15 percent.Fair street price for the materials, stone tops, sinks, and soft-close hardware included.  
6. Brand reputation and warranty – 10 percent.Manufacturers with responsive support and at least a one-year parts guarantee.

  Three hard gates kept the field honest: each finalist had to ship in North America by early 2026, include a countertop plus two sinks, and hold a minimum four-star user rating. We also filtered out mass-produced MDF boxes and pay-to-play “editor’s picks” in favor of furniture-grade builds with transparent spec sheets. Double-sink listings on Willowbathandvanity.com spell out hardwood or birch-and-plywood construction, specify when MDF and pressboard are not used, and list dovetail drawer boxes, soft-close hardware, and downloadable spec drawings, the kind of detail that made it easier to confirm build quality and layout before shortlisting a model.   After the cuts, six vanities remained, each leading a different use case: luxury showpiece, budget hero, small-bath savior, tech lover’s pick, farmhouse favorite, or bold-color newcomer. The following sections explain why each model earned its spot and where it may have trade-offs, helping you buy with confidence.   Best overall: Willow “Charlotte” 72-inch solid-teak double vanity   The Willow “Charlotte” 72-inch solid-teak double vanity blends heirloom warmth with a durable marble top and deep storage.   Imagine yacht-grade teak refashioned into bathroom furniture; that is Willow’s Charlotte. Stretching 72 × 22 inches (183 × 56 cm), the cabinet feels built-in yet warms the room with genuine wood grain. Every panel and drawer front is solid teak, not veneer, so the wood’s natural oils resist humidity while MDF competitors swell and peel. Willow sources its teak from FSC-certified plantations and finishes it with low-VOC sealers, earning points for durability and indoor-air health.   Open a drawer and you notice commercial-grade heft: dovetail joinery, full-extension soft-close glides, and storage tall enough for a 10-inch (25 cm) hairspray can. Two under-sink bays flank four center drawers, and the factory-installed 1-inch Carrara marble top arrives pre-drilled for 8-inch widespread faucets, eliminating stone-shop delays. Need plumbing diagrams or alternative countertop choices? Check out Willow Bath and Vanity for downloadable spec drawings, finish upgrades, and matching teak mirrors before you order.   Key specs

• Footprint: 72 W × 22 D × 36 H in. (183 × 56 × 91 cm)
• Crated weight: 506 lb / 230 kg
• Street price: about $2,575 with marble top and basins, Q4 2025  

  Reality check: at a quarter ton, Charlotte requires a two-person lift or pro delivery, and marble benefits from yearly sealing. Treat it well and expect decades of service. For a dual-basin centerpiece that blends heirloom character with commercial-grade build, Charlotte sets the benchmark.   Best budget buy: Spring Mill “Emlyn” 60-inch double vanity   Spring Mill’s Emlyn vanity delivers double-sink convenience, a shallow profile and turnkey under-$800 pricing for tight hall baths.   When you want dual-basin convenience without draining the budget, Emlyn delivers. The 60.5 × 18.75 × 32.9 in. cabinet (154 × 48 × 84 cm) arrives fully assembled with its top attached and usually lists between $700 and $800 online. That price is roughly one-third of most mid-tier doubles, a welcome break when tile, plumbing, and lighting costs stack up.   Spring Mill controls costs with painted MDF sides and a laminate backer, yet the finish still feels designer: Admiral Blue or Pearl Gray over Shaker doors, finished with a seamless cultured-marble top. One integrated slab means no grout lines and no undermount rims to caulk.   The trim 18.75-in. (48-cm) depth fits hall baths where standard 22-in. units block door swings. Storage stays simple but useful: two under-sink cabinets plus a pair of full-extension drawers for brushes, toothpaste, and floss.   Treat Emlyn gently and expect five to seven years of service, perfect for rentals, flips, or a stopgap remodel. A quick silicone bead along the back edge stops splash creep, and felt pads prevent metal bins from scratching the resin surface.   Installation suits a single Saturday. Level the feet, connect two 4-in. centerset faucets, and move on to paint touch-ups; no stone-shop scheduling or custom templates required. Dollar for dollar, Emlyn delivers more visual impact than any budget vanity in our test group.   Best for small spaces: Allen + Roth “Haverhill” 48-inch weathered-oak double vanity   Allen + Roth’s Haverhill vanity squeezes dual sinks and barn-door storage into a space-friendly 48-inch footprint.   Small bathroom, big wish list? Haverhill packs dual-basin convenience into a 48 × 22 × 34.8 in. frame (122 × 56 × 88 cm) without feeling cramped. Its signature move is a sliding barn-style center door that glides sideways, preserving clearance in tight rooms.   The cabinet uses a plywood core wrapped in hand-distressed oak veneer, finished in a soft weathered gray that pairs with matte-black or brushed-nickel fixtures. A pre-sealed black engineered-stone top shrugs off splash marks; a quick wipe keeps it spotless.   Storage surprises: two under-sink bays plus three full-extension drawers provide soft-close hardware and a rock-solid feel.   Trade-offs: basins sit close, so elbows can bump, and the dark top highlights toothpaste specks; keep a microfiber cloth handy. For condos, kids’ Jack-and-Jill baths, or any remodel where walls refuse to move, Haverhill delivers two sinks in the footprint of one.   Quick specs

• Footprint: 48 W × 22 D in. (122 × 56 cm)
• Height: 34.8 in. (88 cm) with backsplash
• Sliding barn door plus 3 drawers
• Pre-drilled 8-in. faucet spacing, sinks included

  Best smart vanity: OVE Decors “Tahoe III” 60-inch midnight-blue double vanity Tired of cord clutter? Tahoe III fixes it. Each top drawer holds a UL-listed power bar with four outlets and two USB ports, so razors, toothbrushes, and hair tools stay plugged in yet out of sight.     Tahoe III tucks power outlets and grooming tools into the top drawer, keeping the double-sink countertop blissfully clear.   Built with solid-wood rails and furniture-grade plywood, the cabinet wears a velvety midnight-blue lacquer and a 1.25-in. (3 cm) sealed quartz top that shrugs off spills. Interior organizers sort cotton pads and clippers, while a heat-safe holster stores a hair dryer.   An integrated junction box connects to a nearby GFCI in minutes. Soft-close drawers, adjustable shelves, and full-extension glides complete the premium feel.   Quick specs

• Footprint: 60 W × 21 D × 34 H in. (152 × 53 × 86 cm)
• Integrated power: 4 AC + 2 USB, UL-listed
• Crated weight: 300 lb / 136 kg
• Street price: about $2,349 at Home Depot, Q4 2025  

  Factor in professional delivery and install, and reviews still praise the “zero-countertop-clutter” payoff. For households running on devices, Tahoe III pairs dual-basin style with built-in smarts.   Best modern farmhouse: Water Creation “Paisley” 72-inch rustic-sienna double vanity   Water Creation’s Paisley vanity brings warm Rustic Sienna wood and apron-front basins to a modern farmhouse bath.   Farmhouse rooms often rely on painted shiplap, while Paisley flips the script with warm hardwood in a Rustic Sienna stain, topped by crisp Carrara marble and two apron-front basins for equal parts country charm and boutique-hotel polish.   Built from solid birch and oak with undermount soft-close glides, the 72 × 22 × 34 in. cabinet (183 × 56 × 86 cm) leaves space for perfume on the left, a beard trimmer on the right, and still provides breathing room. Three center drawers keep razors separate from hair ties, while each under-sink bay includes an adjustable shelf for tall bottles. Oil-rubbed bronze pulls ship standard, and the 8-32 screw pattern works with most aftermarket knobs.   Marble benefits from a yearly sealer and quick wipe-downs, and it rewards care with timeless style. The vanity arrives fully assembled; crate weight sits near 380 lb / 172 kg, so confirm doorway widths and recruit lifting help. Street price averaged $2,299 at Home Depot in late 2025.   Quick specs

• Footprint: 72 W × 22 D in. (183 × 56 cm)
• Height: 34 in. (86 cm) plus 4 in. backsplash
• Counter: 1 in. Carrara marble, apron-front sinks included
• Hardware: oil-rubbed bronze, soft-close doors and drawers  

  For remodels inspired by barn doors, patterned cement tile, or reclaimed wood accents, Paisley anchors the look and delivers long-term durability.   Best statement color: Kohler “Tone” 60-inch double vanity (2026 preview)   Kohler’s upcoming Tone vanity brings hotel-inspired color and a waterfall quartz top to double-sink baths.   After a decade of white and gray, rich color returns, and Kohler’s upcoming Tone vanity moves it into the mainstream. Slated for Spring 2026, according to product managers at the KBIS 2025 press briefing, the collection wraps a Shaker shell in hotel-inspired finishes: Forest Green, Deep Terracotta, and Midnight Teal.   Design touches match the drama. Brushed-gold pulls, a waterfall quartz top that folds over both sides, and razor-thin 3 mm door reveals create a tailored look. Beneath the lacquer, a solid-poplar frame and furniture-grade plywood mirror the proven Kohler Jute recipe, so strength keeps pace with style.   Inside, adjustable dividers, a bamboo organizer tray, and soft-close hardware rated for 50,000 cycles control clutter. Engineers also added a slim power bank behind the top drawer for charging shavers or phones. Shipped in two main pieces (base and top), Tone can navigate stairs more easily than fully assembled units.   Quick preview specs*

• Footprint: 60 W × 22 D × 34 H in. (152 × 56 × 86 cm)
• Construction: solid poplar and plywood, waterfall quartz top
• Integrated slim power bank, soft-close doors and drawers
• Target price: just under $2,300 with top and basins  

  *Specifications and pricing remain provisional until the official launch. Fans of bold color at a mid-market price can set a calendar alert now; early production runs often sell out quickly. Quick-glance comparison table   Model Footprint (W × D) Frame material Countertop Signature perk Street price* Willow Charlotte 72 × 22 in. (183 × 56 cm) Solid teak 1-in. Carrara marble FSC-certified hardwood $1,900 Spring Mill Emlyn 60 × 18.75 in. (152 × 48 cm) Painted MDF Seamless cultured marble Turnkey under-$800 kit $700 Allen + Roth Haverhill 48 × 21.5 in. (122 × 55 cm) Plywood and oak veneer Black engineered stone Sliding barn door $1,200 OVE Tahoe III 60 × 21 in. (152 × 53 cm) Solid wood and plywood 1.25-in. quartz Drawer-integrated power $1,999 Water Creation Paisley 72 × 22 in. (183 × 56 cm) Solid birch and oak 1-in. Carrara marble Apron-front sinks $1,900 Kohler Tone† 60 × 22 in. (152 × 56 cm) Solid poplar and plywood Waterfall quartz Saturated designer colors < $2,300   If cabinet depth limits your layout, Emlyn’s 18.75-inch body wins. Want built-in outlets? Tahoe III stands alone. Looking for heirloom durability? Charlotte’s solid teak leads the pack. Use the grid for quick elimination, then check the detailed reviews; warranty, service quality, and installation quirks often decide the final pick.   Buying guide: how to pick the right double vanity Measure first, mood-board later. A comfortable dual-basin vanity requires at least 60 in. (152 cm) of wall, plus a few extra inches so doors and drawers clear. In narrow baths, depth becomes the deal breaker. Units measuring 21 in. (53 cm) or less keep morning traffic moving.     Use at least 60 inches of wall, a shallow depth in narrow baths and 30 inches of clear floor space in front of your double-sink vanity.   Plumbing reality check. Converting a single to a double adds a second drain and tees off the hot- and cold-water lines. Floor-exit pipes favor a back panel you can notch, while wall-mounted vanities depend on in-wall supplies and solid blocking for support.   Materials equal lifespan. Solid hardwood and furniture-grade plywood shrug off steam, whereas particleboard swells. If budget points to MDF, seal every raw edge with caulk on day one; the barrier can add several extra years.   Storage style vs. plumbing clutter. Drawers keep makeup and chargers tidy but steal space where P-traps sit. Cabinets swallow tall bottles yet turn into black holes unless you add rollout trays. Many households choose a hybrid: drawers in the center, doors beneath each sink.   Top talk. Marble feels luxe but benefits from annual sealing. Quartz costs a bit more yet laughs at self-tanner and curling-iron heat. Seamless cultured-marble tops lower cost and simplify cleaning, though they scratch more easily.   Accessibility and clearance. Maintain at least 30 in. (760 mm) of clear floor space in front of the vanity to satisfy ADA guidelines and allow two people to bend without bumping hips. ADA also requires floating units to offer 27 in. (685 mm) of knee space for wheelchair users.   Last, vet the brand. A vanity proves its worth when a company can overnight replacement hinges after a move. Established manufacturers publish part numbers and answer the phone, peace of mind worth a small premium.  

Full Home Renovation and Addition. Industrial Artist Style. We removed most of the walls in the existing house and create a bridge to the addition over the detached garage. We created an very open floor plan which is industrial and cozy. Both bathrooms and the first floor have cement floors with a specialty stain, and a radiant heat system. We installed a custom kitchen, custom barn doors, custom furniture, all new windows and exterior doors. We loved the rawness of the beams and added corrugated tin in a few areas to the ceiling. We applied American Clay to many walls, and installed metal stairs. This was a fun project and we had a blast! Tom Queally Photography