Software
Houzz Logo Print
brdldystlu

soaker hose placement

19 years ago

OK I am almost done with building my bed for the asparagus and rhubarb. My question is I have a soaker hose for it, it was in there and now I have it pretty much under an inch or so of soil/compost/manure. Is this ok or should I pull it to the top, which I am fixing to lay a layer of wood chips on the top.

Thanks,

Sandy

Comments (13)

  • 19 years ago

    From the view point of getting the soil wet, it probably won't make much difference, from an aesthetic view point, it would be prettier buried.

    However, if it was buried in my bed, the odds of me putting a hoe or a shovel through it would be pretty high.

  • 19 years ago

    A soaker hose needs much less water to irrigate a bed if it's covered, at least with mulch. I run several hundred feet of it, and it varies from 2" deep to 6" deep in the soil. I run it shallow in beds I use for shallow-rooted veggies like lettuce, and nursery beds, and deeper for everything else.

  • 19 years ago

    How do you mark buried soaker hoses, so you don't cut them with a tool, stake or cage? Do you have any system to know where they are located? I am concerned about the tomato cages and stakes that go everywhere in my garden, and want to place these properly in the ground rather than through the hoses. I have an approximate idea of where the hoses will be underground, but unlike horseshoes, being approximately close won't be good enough.

  • 19 years ago

    Thanks for the replies. Let me tell you my body is really hurting tonight. Here is a photo of the pile they dumped for me
    {{gwi:265148}}

    And here is what is left for me to finish off this weekend-I hope.
    {{gwi:265149}}
    It has been one long winter and my body is way out of shape.
    Sandy

  • 19 years ago

    A soaker hose, made of recycled tires, placed in a properly mulched planting bed would never have to be concerned about getting cut by a spade, shovel, or hoe because you would not need to use these implements in that bed, there would be no reason to. A trowel may be an instrument of harm, in the hands of a careless gardener, but even that should not be of much harm.
    Bury the soaker hose under the mulch because that recycled rubber deteriorates when exposed to the sun, and the water that weeps out will get where it is supposed to before the sun can evaporate it.

  • 19 years ago

    "How do you mark buried soaker hoses, so you don't cut them with a tool, stake or cage?"

    They aren't marked at all. I bury them in a parallel pattern, a foot apart, and I just know where they are. I've slipped a few times, and nicked one, but they're a snap to fix, so it's no problem.

  • 19 years ago

    That is a beautiful sight Sandy, but just looking at that pile makes my bod ache. The day was when it would be no problemo, but that is in the past now. Nice truck !

    Don, how do you fix your soak hoses. The only way that I have found is easy, relatively cheap but if there is a better way I would like to know it. I have tried all kinds of tape, super glue etc., to no avail. The only way that I have found that really works is to cut out a section and put the cheapest hose connector that I can find in to connect the two pieces. The way that I am most likely to damage them is to poke a hole in one with the wire on the bottom of a tomato cage if I move one around for some reason. Even a small hole like that is not good, it will cause erosion of the soil from a little, strong stream and a big wet area.

    I prefer the soakers to drip emitters because of the extensive growth of the roots (as indicated in the excellent old study linked below). Those roots are not confined to a small area aound each plant.
    Bill P.

    Here is a link that might be useful: Root development of vegetable crops

  • 19 years ago

    That's how I do it, Bill. I cut out the injured section, and insert a 2" length of poly tube of the right (or close enough) diameter. Use a razor knife to slice shallow barbs in the poly first, and hold it in place with two ratchet clamps instead of SS hose clamps. I buy the ratchet clamps from Berryhill for $14 for a bag of 100. They're fast and cheap, and since it's a low pressure application, they work fine.

  • 19 years ago

    I've decided to do soaker hoses this year. I checked at Wal Mart and they had 100 foot bulk rolls for 11 something.

    I have a couple of questions about it all:

    1. Do you leave your hoses out over winter, perhaps covered in mulch?

    2. Do you just snake your hose in a crazy pattern or is there a method? (I'm going to have kind of a crazy layout this year because I'm going wild with plants to attract beneficials)

    3. How far from the plants do you try and space your hose?

    4. Is there a guide anywhere that tells you how long you should let it soak? And how often (every three days, once a week) during periods of no rain?

    My plan is to attach two "feeder" hoses to my main garden hose, and water the back two gardens at the same time (vegetable garden and back flower garden that will be mostly dahlias this year), and then move it around front for two flower beds.

  • 19 years ago

    Julianna..I leave mine out all year. In the spring, when the outside water goes on again, I flush them all by removing the end cap and running water through them for a while.

    Most of mine are in either a back and forth zig-zag parallel pattern, or a spiral, depending upon the shape of the bed. Recently, I've started cutting the hose to fit, and using T-fittings, to cut down on the curves. Each leg is capped with an inexpensive PVC threaded plug and a ratchet clamp, instead of the more expensive male fitting with threaded cap. I've also just folded the end back and wrapped a few twists of binding wire over it.

    In general, my soakers are 1' apart, and I plant between them.

    The only way to know how long to run them is to run them for an hour, then dig holes in the soil to see how wide and deep the water penetration is. It sounds tedious, but once you've done it for a certain bed, you know exactly how much is needed.

    I run my soakers and drip systems off the brass 4-way manifolds everyone sells these days.

    {{gwi:265150}}

    I install quick-disconnect fittings on each, and on the feeder for each soaker, so I can water 4 beds at a time, and then easily switch hoses to water 4 others.

    Each soaker is served by a rubber or poly feeder line which is buried in my woodchip paths and run back to the manifold.

    When I build a new bed, I run a feeder to it, so I can easily install either soakers or drip fixtures as needed.

  • 19 years ago

    I made a header out of pvc pipe (it is so easy, even a cave man could do it) ":^) to go across the upper end of my garden with hose bibs (faucets) every 36 inches apart. The header connects to the main supply line along the garden fence with a quick connection and can be quickly and easily removed.
    I can hook seven, 75 foot hoses onto the header and water one or more rows at a time.

    Some things will depend upon your soil, temperatures, how much rainfall you get and whether or not you have some good mulch. But I usually deep soak the rows that need it about once per week or every ten days. More often in the hotter, dryer part of the summer. I also mulch heavily with shredded oak leaves if I have them, some coastal bermuda is my second choice.

    I have a better picture somewhere but without looking for some time for it, {{gwi:265143}} will give you an idea of what I am talking about.

    With my soil and mulch, normally I can open a faucet just over a quarter of a turn open and let it run for an hour to an hour and a half and it will soak deeply along the row.

    I made a probe out of a piece of 1/2" steel rod about 4 foot long with a cross piece welded on top like a T and the bottom end sharpened some. It does not take much experimenting to learn from the resistance encountered, when the soil down deep is getting too dry and hard and needing water.

    It is really a lot easier than it sounds, as you can see here in this first {{gwi:265145}} about how long the steel probe is. Then, you can see in this {{gwi:265147}} how deeply I was able to shove it down into the conditioned clay beneath the row without too much resistance. That tells me that there is ample and adequate moisture down to that depth so that those deep roots can take up moisture and nutrients.

    I could have dug holes to check the moisture but that would be more of a surface thing and might destroy some roots, or I could buy a moisture meter, but then again, It would only reflect the moisture near the surface. I like what I came up with here for several reasons, cheap, easy, efficient and tells me more than the other methods which I mentioned.

    I let the plants get up a little way then string the soak hose right next to the plants, hill a little dirt up over them (perhaps an inch or two) put my cages in place then add about three to four inches of mulch. You may notice in the pictures of the probe above, the soak hoses are not visible, but they are there, doing their fine job.":^)
    I hope this helps some.
    Bill P.

  • 19 years ago

    Donn and Bill, thank you so much for such detailed info!

    The pictures are great, always helps to see exactly what you're describing. I do like that PVC pipe header.

    This is terrible, but I was watering with my sprayer wand, and watering EVERY DAY. (unless it rained) I really guess I didn't know about deep watering and encouraging good root growth.

    I keep learning.....

  • 19 years ago

    You are welcome Julianna. Frequent, shallow waterings encourage shallow root systems which dry out quickly and do not extend like they should to take up the nutrients also.

    Everyone probably enjoys doing a little hand watering, and it is not all bad, just inefficient and can result in some problems like splashing soil up on the lower leaves which can encourage disease on the plants. That factor is greatly reduced or eliminated if you have some good mulch in place.
    Bill P.

Sponsored
Peabody Landscape Group
Average rating: 3.5 out of 5 stars8 Reviews
Franklin County's Reliable Landscape Design & Contracting