Software
Houzz Logo Print
dba_chuck

MTD tractor won't go uphill

19 years ago

I'm having a problem with an MTD tractor that's about 10 years old and uses a 7 speed transmatic speed control. Tthe tractor is fine in speeds 1-3, and 7. In 4,5, and 6 the tractor wont run uphill. Not sure if I need to replace the belts, the var speed pulley, or lube something. (What do you lube, how and where). TIA

Comments (13)

  • 19 years ago

    What model are you talking about?

  • 19 years ago

    Probably the front drive belt.

    First check clutch adjustment, making sure when engaged idler pulley fully tightens from belt. Then check for belt wear.

    Best to replace both belts, because they a PITA to change, and you've got to pull the rear off the variator pulley to get at the front belt.

    The front belt is a 954-280 on most models and rear is a 954-281 on smaller (600 series) and 954-370 on the larger frames. Should be $20 to $25 each. Suggest you buy OEM and not try to substitute automotive or FHP belts. You may save a few bucks, they non-OEM don't last as long, and in case of front belt often result in very "grabby" takeoffs.

  • 19 years ago

    Thanks for the replies.

    Its' an MTD 670 (Model=13AQ670G372). I took off the transmission cover plate and can see the rear belt is in bad shape. It's a miracle it didn't break completely. The front one looks good. I want to replace both. I got the rear one off in about 15 minutes but I'll be darned if I can get the front one off! The manual says to remove the bolt holding the engine pulley and drop it down so the belt clears the belt guard. I can't get the bolt off. When I try the pulley assembly just spins. Tried holding the spindle that attaches the pulley to the engine with a set of channel lock pliers but it still spins when I try to loosen the nut. Any ideas? Should I just leave the front belt alone since it looks good?

    Also what about belts off of eBay? They claim to be OEM and I can get both for a total of $30 incl. shipping. The local tractor repair shop wants $30 a piece. I've had good luck with other parts and repair items from eBay (deck spindles, blades, grill repair bracket, etc.)

  • 19 years ago

    If the engine pully spins, lock the engine inplace. Did you spray some CRC on the bolt? Getting an old belt off is not a problem because you can cut it. Getting the new belt on will be a problem if you can't stop the engine pulley from spinning or if you can't place it around the secondary pulley and roll by turning on to the engine pulley.

  • 19 years ago

    I broke down and bought a set of vice grips to hold the spindle then I was able to use them to keep the pulley from turning and loosen the bolt. With a little work the engine pulley came all the way off. The book says to just drop it down enough to get the belt below the belt guard but the belt is no where near long enough to slip over the botton of the engine pulley unless you remove it all the way. The book also failed to mention another belt guard pin back on the variable speed pulley that had to be loosened (or removed) to slip the belt off of there too. Boy was it a pain to get to. I had to play with locking the variable pulley in different speed positions to find one that would let me get to the nut underneath the pin.

    Anyway, after all that work, I finally got the font belt off and it looks as good as the day the tractor was purchased. 2 hours of fighting with it and I probably didn't need to.

    The rear belt looks like it went through a meat grinder. I probably only needed to replace the rear belt but I ordered both anyway.

  • 19 years ago

    Great to hear you got the engine pulley off. You're right, it's a good idea to go ahead and do both while you working in that area. Oh, I was curious if you checked the quills for bearing problems while you're down there? I don't recall if they have zerks to lube or not. Give them a sideways tugs to see how much play they have. Good luck!

  • 19 years ago

    When you had the engine pulley off, did you put a lite coating of never seize on the crank? If it needs to come off again it will next time. Drive belt changing is never easy, the worst to change are on the MTDs, since theres two belts to deal with. Usally after replacement tho they'll last a long time, more then likely it'll never need another changing. An easy way to keep your motor from spinning again, if needing to remove the engine pulley - remove the flywheel cover on the top of the motor, use a mid sized C- clamp and between two air fins set the clamp to tighten it to the bottom of the flywheel ( not on the ring gear- on the underside of the flywheel only)- itll stop when you try to loosen the engine bolt, the c clamp will rest against the side of the block and hold the flywheel in place w/o damaging the ring gear or anything else.
    Kidd

  • 19 years ago

    I need to do the same belt replacement on an MTD. If I drain the oil and gasoline so that the mower can be turned up on it's side, will that make the belt replacement easier?

  • 19 years ago

    I have an MTD also. When I replaced the belts, I removed the engine pulley using an impact wrench and a six point 1/2 inch drive socket. If you have an air compressor, the job is easier. Just remember to reinstall the pulley and bolt back by hand and torque to the correct specs. The rear belt drive requires that you remove the shift lever bracket. I also had to remove the smaller pulley which has a circlip holding it in place. The OEM belts last a long time. I've had the MTD mower since I bought it new in September 99 and replaced the belts once.

  • 19 years ago

    Are you saying I need a torque wrench to put the pulley back on? Can't I just make it as tight as I can get it?

  • 19 years ago

    If you have some way to keep the crankshaft from turning, you can get it tight enough, by hand, with a socket. but, if not, you do run the risk of it coming loose, especially when you are a half mile from the garage, down in the woods, etc.
    If you use a torque wrench, just run the nut/bolt up tight, and it should suffice. If you hold the shaft, it might break the bolt off!

  • 19 years ago

    If you don't own a torque wrench just tighten the bolt as tight as you can get it... it will likely stay stuck once it has been on for a while... you can add a few drops of medium strength lock-tite ... if you ever need to get it off again heat will destroy the lock-tite bond.

  • 11 years ago

    I had this same issue on my lawn mower. I replaced the upper drive belt and it started working like a charm. I made a video while I replaced the belt. You can see it here. https://youtu.be/G20J6LrHgM8

Sponsored
Custom Home Works
Average rating: 4.6 out of 5 stars10 Reviews
Franklin County's Award-Winning Design, Build and Remodeling Expert