Software
Houzz Logo Print
nsrrider

charging problem on husky riding mower

16 years ago

i have a husky 48 briggs motor v-twin model YTH2148......it does not charge the battery and before long the PTO electric clutch will not engage the mower blades.....

can anyone advise if there is fuse block somewhere that i cant readily locate?

if it is not a fuse, any other likely culprits?

the battery and connections are good.....

thanks for your time!

Comments (7)

  • 16 years ago

    Typicaly only one fuse, so if it starts that probably is OK, do you have a voltmeter that you can test the battery with w/o the engine running, should be 12.xxx volts, once the engine is running should read 13.5-14.5 volts IF the charging system is working.

    Sounds like either the magneto or perhaps diode has gone south, but you need to test things before sheading $$ on parts. A meter can be as cheap as $10-15 from a autoparts, walmart or radioshack, or borrow one from a neighbor. If you borrow invite said neighbor and supply faviorite beverage and enlist their help.

  • 16 years ago

    You will need to ID the type of charging system. SOme have a basic inline diode as the buzzman stated. Many of these had the external square regulator on the left hand shroud which was fed by an AC stator. Then a wire leaves the regulator and feeds DC back to the battery. As the man said, a basic multi-meter and little knowledge, you can get through it easy enough. If you need help to ID what you have, post the model and type # off the engine itself. It is likely on the stamped on the valve cover.

  • 16 years ago

    thanks for the input guys, the battery voltage is right at 12 volts immediately after charging, drops to 8 volts when the PTO is engaged......use it for a couple of hours and it needs to go on the charger again......

    it is a Briggs and Stratton model ELS725 v-twin......

    thanks again!

  • 16 years ago

    Going to need the full number on the engine, xxxxxx-xxx-xx, check out the B&S site to find the location of the number.

  • 16 years ago

    geeezzzz.....finding all sorts of numbers, not sure of correct one....

    on a aluminum metal shroud on the engine shows:
    L 446677, type 0463E, code 050117yg
    on a plate under the seat shows:
    model 96015000103, PNC 960 150001, Ser # 020705B002491

    no obvious plate on the engine itself with a number using the format above and the briggs sites werent much help (probably just me!)

    could the number be under one of the covers or shrouds on the engine?

    thanks for your time...mark

  • 16 years ago

    OK looking at engine Engine Model # 446677-0463-E1, which seems to pop up on the Briggs site it does have a voltage regulator rather than a simple diode. You can pull up the parts list with that #. Might be able to compare the P/N given to what you have.

    Before you buy a new battery, regulator etc you may want to poke around and test with a voltmeter, the batt and reg could be fine, the alternator coil could be shot, seems there is no wiring diagram in that engine info, may need to see if you can pull up a diagram from the tractor or one similar, someplace out of the alternator coil you should see about 20-25 Volts AC, then the regulator turns that to DC to charge the battery.

    Sorry this is just basic info as to how it works, if you can find the wiring diagram for your tractor or a similar one I may be able to direct you to a few more tests before plunking down cash for a part you do not need.

    Have you examined all the connectors on the motor for corosion? Even sometimes pulling them apart and reseating them will 'fix' a problem, but go one at a time so you know which one was the problem.

  • 16 years ago

    Link will get you to Briggs IPL.
    You should be able to match your regulator to the IPL by looking at the wires on the regulator.

    Here is a link that might be useful: 446677 IPL

Sponsored