Software
Houzz Logo Print
knucklehead61

flywheel problems?

18 years ago

Briggs & Stratton m/n 28R707 Type 0148-01.

Awhile back I had some starter problems that damaged the teeth on the gear ring of the flywheel on my Sears lawn tractor. After going through a couple starter gears I removed the flywheel and replaced the gear ring on the flywheel. While in the process I dropped the flywheel and chipped one of the magnets on the inside of the flywheel. About a third of it broke off. I put everything back together and the starter works like a champ but the engine won't fire up. I removed the spark plug wire and there was no arc from the wire. So I'm wondering:

Could chipping a small piece off one of the magnets prevent what my owner's manual calls the magneto armature from generating a spark?

There is a ring of coils beneath the flywheel. Is it possible I damaged one of these coils removing the flywheel? Would doing so cause the problem I'm having? My parts breakdown calls this coil the alternator stator so I'm thinking this wouldn't prevent my spark plug from firing, but what do I know?

All help is appreciated.

Comments (27)

  • 18 years ago

    The magnet(s) and coil under the flywheel that you describe are for the alternator and have nothing at all to do with your ignition.

    Check the magnet on the OUTSIDE of the flywheel. I have heard that a sharp blow may cause it to loose its' strength never had first hand experience with that though. Did you remove the coil on the outside of the flywheel? IF so, did you get it back on right side up? Remove the kill wire plugged into the bottom edge of the coil and see if you have spark.

    By the way, I THINK I told you at the time a used flywheel from any 28 or 31 series B&S engine will work on that.

    Walt Conner

  • 18 years ago

    I see Walt posted while I was typing. He said essentially what I was going to say with this exception.

    CAUTION: If the engine starts, you will not be able to shut the engine off with the ignition switch. Be prepared to pull the plug wires

    Your engine uses flywheel part number 693557. I do see a flywheel on eBay at the link below.

    http://cgi.ebay.com/Briggs-and-Stratton-flywheel-693557-287707-OHV_W0QQitemZ230270738022QQcmdZViewItem?hash=item230270738022

    The flywheel sells for about $150 new and that does not include the ring gear, etc.

  • 18 years ago

    The magnet on the outside is still magnetic. Don't have any way of really measuring its "strength."

    If it starts with the kill wire removed what does that indicate? a bad coil?

    Sears has a flywheel for $120. I was hoping to avoid buying that...

    Thanks for all the info. From what you guys are telling me it can only really be the coil or the magnet somehow. The flywheel will only go back on the shaft one way so I don't think the plug is firing at the wrong time...

  • 18 years ago

    "If it starts with the kill wire removed what does that indicate? a bad coil?

    Opposite- It means the kill wire circuit is grounded, but the coil is good.

  • 18 years ago

    NO, if it starts with the kill wire removed....that would indicate that the ignition (magneto) coil is GOOD. It would further indicate that maybe the kill wire was chafed somewhere causing it to be grounded when it is not supposed to be. Grounding the kill wire is what the ignition switch and/or throttle lever does to kill the engine. If the kill wire circuit developes (or is given) another ground source, it will kill (or prevent from starting) the engine. By unplugging the kill wire from the ignition coil you eliminate the kill circuit from the equation.

  • 18 years ago

    Sorry 'bout that bill, you posted while I was still hunting and pecking on the keyboard. And you are absolutely right.

  • 18 years ago

    unplugging the kill wire did not help. However, the mower did backfire (!!) so apparently I am getting a spark. This happened with the kill wire connected as well. Is it even possible to get the flywheel on out of position so the plug is firing at the wrong time?

    It rained last night and my grass is growing..

  • 18 years ago

    If the flywheel key sheared, the flywheel can rotate on the shaft and totally mess up the ignition timing.
    Sounds like a good place to check!

  • 18 years ago

    Yes, flywheel key is a good place to look if it is backfiring. BTW - the key does not have to be "sheared", just a very small indention in the key has caused me great troubles in the past.

  • 18 years ago

    So is there a trick to getting the flywheel key back in? Seemed pretty simple. I just lined up the shaft and the flywheel and banged the key back in. Didn't look like there was much room for error. Is it possible I didn't get it in deep enough?

  • 18 years ago

    I worked on an old motorcycle recently that had a STRONG blue spark on the plug that was in the motor.... But for the life of me I could not get that bike to start.

    tore down the carb and did about every gosh darn thing I could ...

    and then a friend said - change the plug... and even though that old plug sparked outside of the engine properly... a new plug is what it took to get the motor running perfectly.

    have you checked your plug(s) ? are they wet / fouled ?

  • 18 years ago

    Njdpo, I have a push mower that uses the same plug, and it worked in there. I am going to pick up another flywheel key and pull the flywheel off again and see if it twisted or sheared off.

    Is there a trick to punching the new key in? I used a punch and the key is pretty soft and did deform somewhat when I banged on it. I didn't think it would matter that much as long as it was in place.

  • 18 years ago

    The correct technique for installing key is to place the key in the keyway on the crankshaft (tap very lightly to seat the key completely) and THEN align the keyway in the flywheel to the key in the crankshaft as you very carefully lower the flywheel onto the crankshaft. It sounds like your key never entered the crankshaft keyway with the technique you described.

  • 18 years ago

    mownie's above technique is the proper way to install the flywheel key.

    Very important - the flywheel washer is "cupped"; Be sure to get the concave side against the flywheel when you put it back on.

  • 18 years ago

    Looks like I did screw up the flywheel key. Took the flywheel back off and inserted another key. The original key was in pieces. It started for a second but then died and wouldn't restart. No backfiring. I wonder if the key didn't slide down too far on the crankshaft. Pushed the mower back in the garage last night and will look at it tonight maybe. How deep on the shaft should I place the key? Right at the top?

    The key didn't fit real snug into the crankshaft but it stayed in place when I slid the flywheel down--I could see it. I wonder if there was too much wiggle room laterally and the key deformed after it first fired up. I picked up two from a lawn mower shop on my way back from having Sears ship me one (Sears told me they had one in stock but when I showed up they didn't!). The guy at the shop pulled a handful out from a bin and told me all B&S keys were the same(?). Will try again tonight.

  • 18 years ago

    Yah, the keys are the same. They have a habit of sliding out at the last second. IF they want to do that, I align the keyway in the flywheel and crankshaft and slide the key in by finger, NOT pound it in.

    Walt Conner

  • 18 years ago

    "I wonder if there was too much wiggle room laterally and the key deformed after it first fired up."

    "The original key was in pieces"

    This indicates you did not properly torque the flywheel nut/bolt. There is a wide misconception that the flywheel key keeps the flywheel from rotating on the crankshaft. It DOES NOT. It only ALIGNS the keyways until the flywheel nut/bolt is properly torqued. The tapper of the two parts is what keeps them in position when tightened properly.

    Walt Conner

  • 18 years ago

    What Walt said. Seen it many times.

  • 18 years ago

    Good thing I bought 2 keys. Don't have a torgue wrench so I hope vice grips and a 3 pound sledge will work.

  • 18 years ago

    It's a lot cheaper to buy a correct fitting wrench instead of a new flywheel!

  • 18 years ago

    I took the flywheel off again and there was the flywheel key sheared in two. I put in the new one got everything back together and tightened the nut on the flywheel down as tight as I could. Tapped the ratchet with the hammer a little. Rolled it out of the garage and it fired right up. Mowed a little strip of grass before I put it back in the garage. Will know for sure when I mow later this week. I guess the whole time I just wasn't torquing the flywheel down tight enough.

    Thanks to Walt and Bill and Mownie and everybody else for your help on this. I wouldn't have got this done without you, that's for sure. My neighbors thank you too. Good luck and I'll know where to come with all my problems from now on.

  • 18 years ago

    Visegrips have a lot of good uses,but not in this department.JMHO tbk

  • 18 years ago

    Knucklehead61: You may as well go ahead and buy a torque wrench. You'll need it again here, and you'll find multiple uses for it on other projects. I didn't think I needed one until I kept having to redo a repair I was working on. I now have both 1/2" drive and 3/8" drive torque wrenches. One cannot have enough tools. Ar, Ar, Ar, Ar!!!!! As Tim the Toolman Taylor would grunt.

  • 18 years ago

    knucklehead, put it in proper perspective. You probably saved yourself enough money already by tackling this project yourself to buy a decent torque wrench (and learned a few things too). Remember this as well: When trying to repair anything......the right tools help to prevent inflicting further damage and/or causing personal injury. Besides, you need a torque wrench for more than just securing a flywheel.

  • 18 years ago

    mownie, you're right, I did learn a few things. Got out of this problem for around $30 plus my (and yours) time. Hopefully now I can get through the summer with this beast. I may put a torque wrench on my Xmas list but I ain't the handiest of guys, and don't do this stuff for a hobby, but only when I have to. Of course, if halfway through mowing this happens again, that's the second thing I'm going to buy...after a new key. Thanks again.

  • 18 years ago

    I mowed most of the yard (1 acre) last night and then it got dark. The mower had no problems. Looks like everythings okie dokie now.

    Do I need to do anything to get rid of this forum or will it disappear all by itself?

  • 18 years ago

    It'll fall off the bottom eventually, unless someone else posts to it.

Sponsored