Software
Houzz Logo Print
dhparker

Range Hood Ducting not quite reaching ceiling

13 years ago

Hello,

I plan to purchase a 30" Kobe RA-094 Range hood to go over my 30" gas range. I have fairly high ceilings (12') with the duct cover extension, and a standard 30" clearance over the range - I will still be 6" short from the ceiling. The duct will have already gone into the wall at that point (i.e. won't be visible), but will this look goofy with it stopping short of the ceiling?

Some other options:
- Raise the hood to have a 36" clearance over the stove so that the top of the duct cover meets the ceiling. Is this too much clearance?
- Build a roof box or custom duct extension for the extra 6 inches

Any other thoughts or suggestions from those who have done this?

Dave

Comments (7)

  • 13 years ago

    I had a similar situation but the duct cover was shorter than 6" shy of reaching the ceiling. In my case I have a 12' vaulted ceiling. I didn't like the seams that I would have had if I purchased the duct cover from the hood manufacturer. I purposely chose a hood that had a square duct cover so that I could have one easily made. I had a duct cover made at a local sheet metal fabricator that specializes in making stainless counters and cabinets for restaurants. I measured it about 1/2" shorter than the ceiling height so I could lift it on the hood without gouging the ceiling. I covered the gap at the top with trim molding. The cost of the cover was about $400 which is still cheaper than buying it from the hood manufacturer and they cut the angle to match my ceiling(I gave them a wooden template so they could match the angle).

  • 13 years ago

    Great, thanks for the feedback.. I'll look into a custom trim

  • 13 years ago

    To answer the other question, the maximum height of a hood that retains effectiveness is dependent on how much larger the hood is than the cooking zone underneath it. A 30-inch wide hood over a 30-inch wide range is already marginal, so raising it would not be recommended.

    kas

  • 13 years ago

    Ok thanks. I can actually install a under cabinet range hood with 25" clearance on a 30", with 4x16K BTU burners. Is it essential to have the 30" clearance, or would 25" be fine?

    It would mean less remodelling of my kitchen to get the full 30" clearance..

  • 13 years ago

    My wife's Viking hood is 24" above her range. 20.5" deep, same as that Kobe. Never even noticed it, certainly never hit my head. I'm 5'10", so the bottom lip of the hood is about lower nose level. If I were 6'3", I might have to duck a bit to see things on the back burners. For my remodel, I am putting my new 24" deep hood at 26" off the range.

    One note, her counters are nearly 1.5" higher than standard, so 24" off the range is 60.5" off the floor.

    This post was edited by attofarad on Mon, Jan 21, 13 at 2:44

  • 13 years ago

    Most manufacturers stipulate 30" from burner tops to lower edge of cooktop/range etc. Some high power btu produces, I seem to recall, mention 36".

    An essential question is what does your local city code require? That 30" cooktop to vent hood is pretty common and lowering it may violate code and require a pull and fix.

    I'd suggest going with a custom six inch extension from a local metal worker. It shouldn't cost very much nor take a lot of time for them to do. Good luck.

  • 13 years ago

    SparklingWater, the 30" (and sometimes 36") minimum specification I have seen is from the range top to the unprotected cabinets. i.e., to the top of the hood, not the bottom. The hood alone doesn't comprise "protection" -- less than 30" (or 36") requires an additional fireproof layer along with minimum metal thickness.

    My Broan hood specifies that the bottom lip is to be between 24" and 30" above the cooking surface, with 24" minimum being a "rule" and 30" maximum being a "recommendation."