Software
Houzz Logo Print
ionized_gw

evap cleaning

19 years ago

I would like to clean the evaporator coils on some window units. Can anyone suggest effective methods?

Comments (11)

  • 19 years ago

    Well the best way if they are very dirty is to remove unit from window and clean with coil cleaner and water.If mostly surface dirt you can use a stiff brush and a vacuum.Be careful not to bend the fins.You can even use a self rinsing coil cleaner and wet vac.If the evaporator coil is dirty I would also check the condenser coil.Look through the side louvers at the inside of the condenser coil to see how much dirt has accumalated.They can get pretty dirty and greatly effect the cooling capcity of a window unit.That why I like to pull them and wash with the water hose.

  • 19 years ago

    Thanks, where can I find said coil cleaners?

  • 19 years ago

    I have shopped around for some sort of specific cleaner, but I have never found one. Any brand names or suggestions about what kind of store would be very helpful to me.

  • 19 years ago

    You know coil cleaners are nice but like most products substitutes are available.

    I repair window shakers and what I do is to remove the covers, locate the motors and either cover them or avoid spraying in that area.

    I make a bleach (10% solution) and spray the coils and tray that collect the water. let it sit a bit while I get the garden hose and rain suit on.

    Then I open the valve and flush the junk out of whereever it may be. Then let it sit for a few hours, reassemble it and plug it in and test it with a thermometer. If I have at least 20 degrees lower in the supply air stream I mark it 'Works great' and set it with the other units.

  • 19 years ago

    www.grainger.com

    They are an industrial supply store that only sells to businesses, but look up the evap coil cleaners for an idea. I have used their non-acid, self-rinsing evap cleaner - Acti-Klean, part# 5W402.

  • 19 years ago

    I am familiar with grainger. That stuff is discontinued according to their web site. I can troll for others, I suppose. I don't want to remove the units for cleaning. We have been living in a rental since Katrina and I have to resist messing with the landlord's stuff. I will put down drop cloths and some absorbant rags around the units on the inside and have at them with some conventional cleaners, probably.

    I am pretty sensitive to mold and other stuff growing in these things. I have cleaning my car HVAC down pretty well, but window units are new for me.

    Thanks everybody. I welcome any more suggestions.

  • 19 years ago

    "I can troll for others, I suppose."

    - Start trolling. A non-acid, self-rinsing, biodegradale cleaner is what you need. The bleach solution also sounds good. Not sure what else you're looking for (Windex, Pledge, Mr Clean?).

  • 19 years ago

    Be even careful with non-acid foaming cleaners. Those are alkilyne type and can be just as corroding as acid. Rinse the coils COMPLETELY or the residue will slowly eat the coil and fins up.
    I try to get by with just a good degreaser first and a good flow of water. For embeded hard to remove debris, I'll use the alky cleaner. Shiny is nice, but not at the expense of ruining the coils.

  • 19 years ago

    Daddo:

    Not sure why the cleaner I got from Grainger 2 years ago is no longer offered. It states that it is self-rinsing, non-toxic, deoderizing, and it didn't foam. As I read the ingredients: sulfonic acid, glycol ether, petroleum naptha, water, surfractants. Hmm, I thought it was non-acid. I have to dilute it with up to 6 parts water.

    I used it twice so far in the past 2 years and am happy with the results. I especially like the self-rinsing as the condesate rinses it off the coil.

  • 19 years ago

    It's always the good stuff that's the first to go.
    HVAC parts houses have a spray on self rinsing stuff. I never use it, but it may work well.

  • 19 years ago

    Note to all. Chlorine bleach is very corrosive as well. I would not hesitate to use it, but I would not leave it for extended periods. I use several types of disinfectants in the lab for bio-hazardous stuff. Bleach has its place, but I have seen ignorant or careless use of it spoil some expensive metal items. That is one reason I have banned it for surface-sterilization at work.