Software
Houzz Logo Print
poolexpert

Repair guy

18 years ago

I have a question for you since I just focus on construction.

My friend has a Jandy rs-6 one touch and the indoor display is no longer back lit,I'm told the repair part is just shy of a total up grade. He's selling his house is there any back door alternative? The units 4 years old.

Comments (11)

  • 18 years ago

    Pull controller off wall. Check voltage at the red and green wires. 1 & 4. If voltage is 8-10DC the controller is bad and you have no choice but to replace it.

    If voltage is 7DC or less, go outside to the power center. If 8-10 on the same terminals then there is an issue with the wiring to the controller inside. Could be broken or undersized. If less than 7DC outside at 1 & 4, then you need to check the transformer secondary wires which are 2 yellows. If less than 22VAC you then need to check the incoming source. Assuming you have at least 105VAC there, and less than 22VAC out of the transformer you have a bad transformer.

    If you have a good 24-28VAC out of the transformer but still have less than 7DC outside you then would kill the power to the whole thing and check the fuse on the power center board.

    In this order:
    1. Power off
    2. Remove fuse and check continuity.
    3. If no continuity, unplug all the valves from the board, replace the fuse and power up.
    4. If the fuse blows, with the valves unplugged, the board outside is bad. Replace it.
    5. If the fuse does not blow, run a test of one valve in the intake socket and move the valve with the system.
    6. If the fuse does not blow, run each valve into the intake socket and move it with the system until all have been tested.

    That should find a source of voltage drag and no light. If it all checks out, then yes the only option is to replace the board. With an RS6 the only option you have is the upgrade kit which is about $800 cost.

  • 18 years ago

    Thanks for the help. I'll check it for him.

  • 18 years ago

    Yowzer Repair Guy! You've done a few of those, haven't you!

  • 18 years ago

    They don't break but often but when they do, they really do. That's the only thing bad about automation. When it fails, it fails hard and expensive.

  • 18 years ago

    so Repair Guy.... what would you consider Good Automation?? please rank them for us learners...

  • 18 years ago

    Jandy makes a very reliable, proven product. My only issue with them is that if you want to upgrade, you get screwed. They require a firmware upgrade.

    Pentair can upgrade with a flash of the firmware for free. That's a 1k advantage right there.

    As most cool products are now under the Pentair line, their automation offers the best value. I do think they are a bit difficult for the owner to grasp but once learned, it's pretty easy. Pentair is a bit more advanced too.

    Goldline is my least favorite because it is just a bit too cheap for my tastes.

  • 18 years ago

    Actually the problem is much easier to diagnose.

    If the backlight doesn't work any everything else does, then it's a problem with the panel inside the house.

    If there was a voltage drop through the wiring the backlight would be dim, or flaky, but still would do something. If you are getting data back and forth and all of the other led's light up, they you should be in good shape.

    I'd pull it off the wall and put it on a pig tail from the outdoor controller if you really want to be sure that it is not the wire.

    If nothing else works at all I would check the fuse, but if you blow the 3amp fuse, nothing would work at all.

  • 18 years ago

    Repair guy, what is your recommendation for a brand of salt water chlorinator (35k gallon pool, gunite).

  • 18 years ago

    Its typically a good idea to start a new thread instead of hijacking another.

    One of the main reasons is that you will get more than one answer to your question, and other community members in the future can access the same responses as you received without stumbling across them.

  • 18 years ago

    Hey belt,

    I answered you and made it a new thread.

  • 18 years ago

    Yep. Saw that, repair guy. Very much obliged! Love your posts.

Sponsored
High Point Cabinets
Average rating: 5 out of 5 stars21 Reviews
Columbus' Experienced Custom Cabinet Builder | 4x Best of Houzz Winner