Software
Houzz Logo Print
progsooner

Craftsman opener - problem after repacing gear

20 years ago

I recently replaced the white gear in my 1/2 hp Crafstman opener. Everything seems to be put back in order. When I try to open or close the door, it will move about 6 inches and then return back to the up position. The lights do not flash so I do not think it is my sensors. They have solid green lights as well. I have tried to adjust the "down" tension but it doesn't seem to make any difference. Would it matter that I don't still have the cover on the unit? In the little time it works (6 inches) it seems to function just fine - it just wont fully open and close. Thanks for any help.

Comments (12)

  • 20 years ago

    I think you need to see where the up and down limit switches are. When you reassemble the chain on the drive gear, the trolley needs to be in the position that it was when you removed it (or reasonably close).
    If you have the instruction manual, review the part where the chain gets attached, for the proper sequence to assure that your positioned within the operating range.

    HTH

  • 20 years ago

    I had the door in the open position when I took off the chain. I then closed the door manually, but the chain tightening mechanism was still near the opener. I took the chain off of the gear sprocket and it still will only move 8 inches or so. I have tried adjusting the up and down force but this still does not seem to make the trolley move much in either direction. When I took the chain off, the spocket did not turn any longer than when I had the chain on moving the trolley. I have tried to read the manual but I don't see anything relating to this. I believe I have the wires back on the capicitor on the correct side and I definately have the blues on the same side and the reds on the same side. Could I have missed a wire or something else. Thanks for any help.

  • 20 years ago

    On the end of the motor shaft is a black plastic interruptor cup. Did you remember to replace this. Make sure it is pressed firmly onto the motor shaft. Also there is a quick disconnect with 4 wires that goes to the IR sensor board. Make sure that is on correctly.

  • 20 years ago

    Don,
    I have a 41A3066 Sears Craftsman garage door opener that stopped working last winter when the chain broke. Now I have reinstalled the chain, and the motor shaft turns about 1 turn and then it reverses. I have taken the chain off and manually worked the door and it goes up smooth. With the chain off the motor still turns the spindle about 1 turn and then reverses back to original position. What do you recommend that I do? I cannot find the manual in this house that I have moved in 1 year ago.
    Thanks for your help,
    Doug Field
    DougFie@aol.com

  • 20 years ago

    Don
    I rechecked the instructions and I have all of the parts that go on the end of the motor shaft installed correctly. The bearing, flat washer, spring washer, cup washer, & collar all seem to be in the right location and firmly tightened. I do not see a plastic interruptor cup. Is it supposed to be on the other end of the motor shaft or is this on the drive gear?
    I also rechecked the sensor board. I assume this is the same thing as the "limit switch assembly". All the wires are connected and the assembly is firmly in its place. The instructions indicate to push on each side and lower for installation of gear. All of this is back to its original location. One thing I tried was to lower this limit switch assembly and see what happened. It did not do anything different. The trolley still moved forward (to close door) about 8 inches and then back (open door) the same 8 inches. It appears to me you "fine tune" this if you need to open or close the door more but it seems to not matter for me as the door does not move far enough for these adjustments. If I adjust the up or down pressure to be really close to the metal "T"s on this limit switch it will stop moving from that direction. However, if I place these limit switches away from the center, it never touches or makes contact. Something keeps stopping the trolley from moving more than 8 inches. I have no obstructions and the track the trolley rides on is smooth and somewhat lubricated. I am about to throw it in the trash but after spending $45 on the new gear, it has become a "pride" issue to try to fix it. Thanks for all you help.

  • 20 years ago

    That black plastic interrupter cup goes on the end of the motor shaft pointing towards the door. If it is not there the logic board senses the door has hit something and reverses to the open position. The door will normally travel a foot or two before this happens.

  • 20 years ago

    Do you think I can get that cap at Home Depot or Lowes or would I have to order from Sears? I appreciate your help.

  • 20 years ago

    That interruptor cup is an item that will not be available at hardware stores. Call around to your local garage door opener companies and ask if you can buy an interruptor cup for a Craftsman opener. They should have some laying around from old openers they have replaced.

  • 20 years ago

    I will try that out - thanks Don

  • 20 years ago

    Progsooner, I have the exact same problem as you describe. The black cup is at the bottom of the shaft the the gear is on. It's right next to the limit switch assembly.

    Did you have any luck getting it to go more than 8"? When I first powered it back on before I put the chain on, I hit the button and the sprocket turned for about 10 seconds, but then after I put the chain back on and tightened it, that's when came up and hit the light slightly and from then on only goes down about 8" and then back up 8". I'll keep researching and let you know.

  • 20 years ago

    The black interuptor cup goes on the end of the motor shaft. On the bottom of the shaft that holds the drive gear is a smaller gear that turns limit switch.

  • 20 years ago

    I called the craftsman GDO tech support line and the tech said that if there is any play in the shaft at all then that is the reason why the trolley will only move about 8" or so. I took the motor off and the reseated the bearing, washers and collar and tightened them securely and then saw that there was no play and sure enough it ran through a cycle fine. I also noticed in the directions that it said to put the chain back on with the door in the down position and tighten it. I did this as well and after some major adjustments everything is working great. The whole thing cost me $21.00 plus about 4 hours of aggravation but it beats paying for a new unit. Thanks to all...especially for that 800 number.