Software
Houzz Logo Print
pammyfay

tacking an extension cord down

20 years ago

I need to run an extension cord along about 2 feet of wall to the corner and continuing behind a bed and about 4 more feet to a floor lamp's cord. (I need to use that far plug because it's the one that is activated by the switch near the door.)

What gizmos are out there to keep that extension cord relatively flat to the baseboards, so there's no tripping hazard?

Comments (16)

  • 20 years ago

    an extension cord is NOT rated for permanent use.

    that being said, i would get a large staple gun and staple it down. you MUST get one big enough that the staples will pass on either side of the cord without nicking it. if this is one of the flat cords, a T-25 cable staple is perfect. but the cheap flat ones are also prone to failure fairly often, we just had one break the other day and the hot an neutral both were exposed at the same point.

  • 20 years ago

    As said above, extension cords are meant for temporary use only.

    If you don't want to go to the hassle of fishing wires through the wall and installing another outlet in the proper spot, then I'd suggest using plugmold to run the wires over the surface of the wall to the new location. It's pretty easy to install. And it's the proper way to do it. Extension cords cause a lot of house fires.

  • 20 years ago

    Plugmold is a product from Wiremold. Wiremold is what you want. It is a plastic square tube used as a conduit or raceway for wiring. Google them and they have a pretty good website of their products. There are metal ones too, but you have to get them from an electrical suppy company. Wiremold is available at big box hardware stores.

  • 20 years ago

    "an extension cord is NOT rated for permanent use."

    What do you consider "permanent use"? She wants to "extend" a single lamp cord ~6ft. Sounds like the corect application for an "extension" cord. Shes not burying it inside a wall and wants to be prudent about not creating a tripping hazard. Are all your lamps hard wired in your house? Should she splice a longer cord on? The tripping hazard will still exist. As far as I'm aware cord ratings are based on load not time of use.

    That being said, if you want to staple it down, then get "insulated" staples. These have a plastic insert to prevent shorting of the wire should the staple cut through the wire insulation. You might also consider something like a "cord concealer". See the link.

    Here is a link that might be useful: cord concealer

  • 20 years ago

    Extension cords are meant to be used temporarily as a means of getting power somewhere for a short period of time. For example, using portable power tools, extra light for a specific task, etc.
    There is a reason that all of your wiring in your house is within your walls, and it's not just for looks. It's to protect it from damage. That's also why outlets are required every 12 feet along every wall ... so that the cords on lamps, etc, are no longer than 6 feet. The more exposed wire there is, the more chance of damage.

    Of course, she could string that extension cord around the room and nothing will happen to it and it will work perfectly for the rest of her life. But then again, I could drive around in my car and never get into an accident, but I'm still going to wear my seatbelt just in case.

    I'm just suggesting the safest way to do it.
    Hope that didn't sound too preachy.

  • 20 years ago

    OK, me again...

    1) I came across 3M Command "Clip Organizers" at Target. They look large enough to hold the cord without damaging it (they work just like the other 3M Command products, with a plastic tab that could be adhered to the baseboard).

    2) That being said, with the debate this prompted (I am actually grateful for that!), maybe I should just take the lamp to the lamp store and ask them to extend the cord! I really don't want to risk any problems, and I'm sure now that even if I used Wiremold (or other covers I've seen at the Depot), I would still be worried that something could happen (and it happening out of sight, because that cord connection would be behind the bed).

    Thanks for giving me something to think about!

  • 20 years ago

    pammyfay-
    Getting a longer cord on the lamp is not going to make it any safer than simply using an extension cord. What is the problem you're worried about? My kids think I'm totally neurotic about safety, but plugging a lamp into an extension cord is not even on my radar screen for problems. Lamps do not use very much energy. Unless you're planning a room with huge grow lights, this is a non-issue. Do you think Home Depot would be selling 100's of thousands of extension cords a year if it caused people's houses to burn down? You have to satisfy yourself, but I think you're worrying too much about this.

  • 20 years ago

    Well, kudzu, considering that the lamp will not be used all that frequently (it's in a guestroom), maybe I am overthinking this. Thanks for your point of view.

  • 20 years ago

    pammyfay-
    I re-read my last post, and I think I sounded a little curt, so I'm glad you weren't offended. But trust me -- and you're hearing this from a certified neurotic -- it just shouldn't be a worry.

  • 20 years ago

    Don't get me wrong, I'm not saying that it is a huge danger.
    I'm just saying that the 'right' way to do it is using Wiremold to protect the wire (it's not the connection, it's the length of exposed wire that is the problem).

    In fact, if I was in this situation, I might even use an extension cord. But if I thought that the cord was in a position where tacking it to the baseboard would make it safer than just laying it on the floor, then I think it would be 'in the way' enough that I'd use Wiremold.

    If you're going to use an extension cord, I would suggest using one of the heavier duty, thicker cords that give it more protection. Those light-weight cords that are similar to the lamp's cord can get nicked pretty easily.

    And by the way, the fact that it is just a light load on the extension cord doesn't matter (although overloading an extension cord is a whole other problem that isn't a factor here). If a pair of scissors gets knocked off the back of the bed and falls on the cord and cuts through it then the
    resulting short circuit will happen whether there is 40W light bulb or a toaster plugged into it.

    I just believe people should be aware of the problem and then make up their own mind about what safety measures to take.

  • 20 years ago

    pammyfay
    plug you lamp in with the extension cord. Use your clips and forget about it.

    greg_h

    Here's the original post.
    "I need to run an extension cord along about 2 feet of wall to the corner and continuing behind a bed and about 4 more feet to a floor lamp's cord"

    here's your latest responses:
    "(it's not the connection, it's the length of exposed wire that is the problem)."

    "If a pair of scissors gets knocked off the back of the bed and falls on the cord and cuts through it"

    c'mon. she's clipping to a wall for about two feet. Stop thrusting your paranoia on others. There is nothing at all wrong with what she's doing.

  • 20 years ago

    It's actually 6 feet (2 along one wall and 4 along another) and I really don't care what she does. I even admitted that I'd probably use an extension cord too, but I wouldn't bother tacking it down.

  • 3 years ago

    Is there any new technology out there since this original post to help the situation? I read elsewhere that battery table and floor lamps are now available. https://www.thespruce.com/best-cordless-lamps-5271852

  • 3 years ago

    There are devices that plug into a switchable wall receptacle and transmit a RF signal to a companion device that is plugged into a normal always on receptacle.

    Turn the wall switch on, powers the transmitter, turns on the companion device and lamp lights. I've owned the one I use for over forty years - not a new-fangled gadget.

  • 3 years ago

    Googled on remote lamp switch.... dozens of solutions.

    Most require either wiring a device in and/or mounting a new wall switch. I prefer my device.

    OP. Why didn't you Google this???