Need help with bobbin holder, bobbin & threading

20 years ago

Hi everyone. I had a little trouble recently with my Singer Starlet 354 (about 20yrs old ) and I order several replacement parts. I had to dismantle "everything" but thanks to the Parts Manual and some pictures I took I was able to put everything back together correctly except one piece (i think).

Everything runs smoothly but when I threaded the machine the thread from the bobbin is not getting picked up by the needle from top. I followed all instructions but nothing worked. I've been on it for three days now and nothing works. All I need to know is how the threading works from below. How or what makes the thread from the bobbin go through the needle plate hole?

The instructions say that the needle will pass into the needle plate hole and come up with a loop that will have the thread from the bobbin hanging there for me to pull through.

How do I position the bobbin holder? or how should I position the bobbin rotater below the bobbin holder before putting the belt from below? Or does anyone know what I am doing wrong? Please help!!!

This post might be a little confusing but I would really appreciate any help with this. Thank you in advance :)

Sort by:Oldest

Comments (3)

kathi_mdgd
20 years ago
http://pages.sewing-machine-manuals.com/173/PictPage/1922657337.html

Christine,
What parts did you replace,did you replace any of the bobbin parts,and did you take the bobbin area completely apart??? I'm not familiar with your machine,but i have had other singers in the past.
Does your bobbin area have a bobbincase that comes out,and did you take it out??.If so you may have not gotten it seated back in correctly.Check that out.Then make sure you have your needle in correctly.Does the needle thread from the side,or front to back?? Also make sure the bobbin is in correctly,the machine i have now ,the bobbin can only be put in one way or else it won't work.Fortunately my bobbins have a "H" on them so i know that is the top.
Wish i was there to help you figure it out,as i'm sure it's something simple and may just be being overlooked.Do you have the manual??

Try the above things and see if any one of them helps.Please let me know how you do.
Kathi
christine9
Original Author
20 years ago
Hi Kathi,

Thanks for all the great advice.. I bet I did put the bobbin holder in the wrong way. I took everything apart.. including the bobbin area. I'm sure that's where the problem is. I read around a bit more and found out that it's probably the timing. The driving belt is not put on right. I found a website that explains how the bobbing thread is pulled up by the needle so I got the idea now how the timing should be. There is a little hook on the rotating bobbin case that should push in thread from the top and catch the bobbin thread from below. I'll let you know if it worked. Am still working on it.

I've read all the manuals but they only give the basic information.. not enough.
I'm sure I put in the bobbin the right way. I have to check the needle again though. Thanks for that tip. I think the needle goes front to back vice versa.

BTW I have the manual and the spare parts manual.

I'll keep you updated.. thank you so much.
Related Professionals
Asheville Furniture & Accessories · Gary Furniture & Accessories · Portsmouth Furniture & Accessories · Bismarck Furniture & Accessories · Hilo Furniture & Accessories · Columbus Interior Designers & Decorators · Richmond Interior Designers & Decorators · Beckley Interior Designers & Decorators · Bangor Interior Designers & Decorators · Platteville Interior Designers & Decorators · Stockton Interior Designers & Decorators · Billings Interior Designers & Decorators · Gaithersburg Furniture & Accessories · Dubuque Furniture & Accessories · Redding Furniture & Accessories
christine9
Original Author
20 years ago
ok here's the update:

I finally got the right timing and the upper thread picks up the bobbin thread now. Also I had the needle up too high for the hook so I lowered it a little.

I've been successfully sewing a few inches and then either the upper thread breakes or it skips stiches or the rotator at the bottom gets out of timing again.
I'm still experimenting with the right combination of stich length and tension.

Thank you so much again for your advice.