Software
Houzz Logo Print
bluestarrgallery

Pedastal Table Top Advice Please

19 years ago

You may recall my asking about the amber glass and mosaicing my large bowls, well I haven't gotten to them yet - but I will.

I decided I needed a table top for this bird bath pedastal sooner than I need the bowls, because the table is in my living room. Anyway, if I seal it real well, do you think I can use this round wood for a base? I thought about using hardibacker on it, but it is already heavy and with the hardibacker it will be real heavy. Also I am not sure what to do with the edges of the wood - someone suggested I cover it with copper sheeting - I was thinking of kid of a hammered copper look? Or do you think I could mosaic the sides too?

What should I seal the wood with - I was thinking of several coats of kilz or I could use redgard? What do you think I should do to the edges? What should I glue the glass and stone tiles down with? I have some thinset left over from laying slate in the living room - would that work? Please keep in mind I am a total beginner - and know nothing about doing mosaic.

Here are a couple of photos of the base with the top just balanced on top. And then the top with a draft design which I plan modify.

Thanks for any advice.

{{!gwi}}

{{!gwi}}

Comments (12)

  • 19 years ago

    If you don't plan on it being outside at all, there's
    no reason to go beyond the Weldbond/water seal before starting.
    If it will go outside, Redgard won't even save it.
    Linlee

  • 19 years ago

    I have sealed my tables with just primer. A Kilz type. None of mine go outside. Very pretty design.

    I used the curved edges of a bowl I nipped up for a curved edge like you have. I don't know where a picture might be if I even have one. You can also just paint the edge or use bull nosed tiles around the top edge and grout up to them. More work would be to sand the curve out of the edge giving you a flat surface to glue to.

    Looks like a great project to me.

    Chris

  • 19 years ago

    Love the design and colors. I always use Kilz, but keep stuff like that inside.
    You really dont want to put that outside, do you?
    Ingrid-Em

  • 19 years ago

    Beautiful design,you'll have to keep it inside...weldbond and a tiny bit of water will work to seal it.Where did you buy your glass tiles? They look precut?

  • 19 years ago

    Wonderful design. Since this is a birdbath pedestal, IMO, it is heavy enough to take the hardibacker and a larger round. The tesserae would work sooooooo very well w/a hammered copper covering around the edge of the table. I can't remember which artist used it on one of her torsos, and it was lovely.

  • 19 years ago

    linlee, what do people put outside stuff on, solid concrete? or hardibacker on wood - will that work?

    shades of idaho, I might go by the thrift store and see if I can find anything that is already curved I can use - I was kind of wanting something with color on the sides.

    Ingrid-Em, loved the light you did in the other post. I think this should stay inside - don't want all that work to go to waste.

    crackpotannie, believe it or not I got all the tiles at Home Depot in anther city - my HD didn't have these. They all came stuck on little sheets and I took them off - the glass tiles, stones and ceramic tiles all came in the size shown. I was trying to do it the easy way the first time, but then I started looking at the design and seeing some blank spaces and wanting to fill them in - so I guess I should get a tile nipper. I am going to run back and get a few more of the aqua and gold ones and substitute more glass for the ceramic squares and just have glass and the irregular stones - which I think would look better. I also want more color and contrast in the table. We shall see.

    slowmedown, the pedastal is solid concrete so it can take a heavy load. The wood form is 18 inches in circumference. I was just trying to save myself the trouble of getting a sheet of the hardibacker - but maybe I should just get it. I might be sorry if I don't. I wish I could see something with the copper around it to see how it was put on - I am trying to picture it in my mind - whether the copper should cover the edges of the tile or just cover the wood - and how to attach the copper so I don't see the attachment - maybe I can get some copper brads to attach it? I will have to check at the hardware store to see if I can get some. If I glue the copper, will that GE II work?

    I was thinking of laying out the design on the board, then putting tape or contact paper on top and lifting the design off, then spreading thinset over the board, then laying the design back on - do you think that will work?

    I have so much outdoor stuff (winterizing and putting up a fence) to do and I really want to do this mosaic project instead. But cold weather is coming and I have to winterize an extensive irrigation system. Last year we had 7 valves crack (we had a very unusual hard freeze for here). And the valves aren't cheap - so I want to prevent that this year. We had drained all the water out, but apparently there was a small amount of water behind the ball valve and it froze and expanded and split the valves.

    Thanks for all your advice, I will keep you posted as this project progresses.

  • 19 years ago

    Along with some more glass tiles, I got some copper roof flashing at HD yesterday. The flashing seems very piable and easy to work with. It comes in a roll - 8 inches by 20 ft. I am going to my ceramics workshop today and the studio has some copper they have treated to give it a patina - I will ask them what they used to obtain that look.

    I also got some upholstery brads and some antique copper headed screws - not sure how I will attach the copper to the sides of the wood base - but wanted a couple of alternatives. The upholstery brads have some nice decorative tops - which might look nice along the edge - we shall see.

    I just noticed on the back of the glass tile - the laying instructions say to "use only white modified poly blend thinset" and couldn't find any at HD? Maybe a tile store will have some. Anyone know where to get this stuff? thanks.

  • 19 years ago

    My HD has finally started carrying poly thinset but they didn't have it in white. I also couldn't find it at Lowe's but I bought regular white thinset (said suitable for glass on the bag) and then the liquid poly to blend instead/in addition to water. I don't think you have to use white, just shows through and reflects clearer glass better. If you search posts here, there are some real experts who work with this all the time.
    Never used contact paper but I'd test the weight of your heaviest stone on it before I did the whole pattern. I think one of my books uses that method. After you lay your thinset, you may have to butter the backs of your glass tiles to bring them up to the same level of your stones. Can't tell from your pic. The poly thinset does stay flexible alot longer than the regular. Hope I'm not sounding "know it all", I've just done all the above wrong at least once!

  • 19 years ago

    Honestly not sure of all the methods outside.
    Do know that wood is iffy. However glass & cement
    can outlast us.
    No matter how well sealed something is, water always seems to find a way in to warp, rot and in this application pop off tessera.
    Have you thought of pouring you own cement table top?
    Or maybe a large round stepping stone?

  • 19 years ago

    diytrying, thank you so much for your advice, I can use all the help I can get, since I have not done anything in mosaics before. I just wanted a small round table for my living room and it has snowballed into this. I am going to call my tile store where I got my slate and tile for the bathrooms and see if they can get the white poly premixed. My glass tile and stones are actually about the same depth - but I know about back buttering because we had to do that when laying our slate floor in the living room - the slate was all different thicknesses.

    linlee, a cement table top - now why didn't I think of that - you are brilliant - then I could use it outside and inside or if it gets moist I won't have to worry about it. And its got that little metal rod sticking up and I could make a place in the center of the table top for it to fit. Hope it doesn't come out too heavy. I will have to talk to DH this evening when he gets home about the best way to go about this. Thank you so much for your advice.

  • 19 years ago

    It doesn't show very well in the picture, but JMD Mosaics is where the artist used copper around her "Woman Stompin' Grapes" sculpture. Here's the link.
    copper edged base

  • 19 years ago

    thanks, slowmedown, I see the copper at the bottom of the torso. I was talking to my ceramics instructor and she has copper sheeting covering her ducts in her studio and she gave them a patina to age them. She used vinegar and salt and heated it till the salt melted and the vinegar wouldn't absorb any more salt - gives a green tint. She also used amonium sulfate (fertilizer)- gives a blue tint. And she used liquid nails to glue the duct work together.

    I am now wondering if I shouldn't just make a concrete base for the table top as linlee suggests. But I do like the copper and will probably utilize it for another project (got to justify buying it and keeping it rather than returning it - right !). DH thinks I am a pack rat - I need my own studio and then he wouldn't see all that stuff hanging around. Ha!

    Thanks for taking the time to post the eye candy on the JMD site.

Sponsored
J.Holderby - Renovations
Average rating: 5 out of 5 stars4 Reviews
Franklin County's Leading General Contractors - 2X Best of Houzz!