Software
Houzz Logo Print
skyangel23_gw

hitting budget ceiling--cabinet end panels

12 years ago

We are about maxed out after our drawer stacks, dovetail construction drawer upgrades, a few glass cabinets, and soft white factory painted finish on our shaker-style cabinets.

The ends of cabinets will be a white vinyl "skin" unless we upgrade. We can do plain 3/8th thick veneer panels that are about $500 (for four panels, two wall, two base), or the decorative end panels that repeat the door pattern, for about $900. The ends of the cabs can be seen from the kitchen and the family room.

It would be stretching past my comfort zone to do the decorative panels, and even the plain ones. I would have to give something significant up to get them now, and I have already gotten rid of all the upgrades I don't really love.

How important are end panels versus vinyl skins for painted cabinets? And, is it possible to just do the skins now and then order end panels later? Would they be hard to DIY install?

Thank you so much.

Comments (12)

  • 12 years ago

    Are finished ends not a possibility? I have shaker style and only one truly exposed end that is essentially covered by the fridge next to it so I didn't do skins or decorative panels. My cabinet maker just built them with plywood finished ends that I stained to match the fronts.

  • 12 years ago

    We refaced our kitchen cabinets last fall. For the back of our peninsula we opted for the doors, and did 3/8" end panels for the cabinet ends. I would not go with vinyl skins myself. The end panels are very simple to install, especially if you order them cut to fit. Doors for the ends are not hard to install either, although our counter top was also off when we hung the doors on the peninsula back, which made it a bit easier to do.

  • 12 years ago

    I'll let the experts chime in, but in my personal experience different materials will age at different rates, producing a color variation over time, even if they look somewhat close at the beginning. If I planned to stay in the home, I would get the veneer ends and then cut somewhere else where I could upgrade more easily later.

  • 12 years ago

    If you are inset, there is no going back and installing door panels later and it ever looking right. Plus, applied door ends adds 3/4" to the cabinet footprint that has to be accounted in the design or when templating for counters.

    I'd never ever do vinyl. Your cabinet line should offer a flush finished plywood side, and if I had to cut, that's the lowest level I'd cut to. But, I'd cut out inset first, and keep the integrated dor ends. You're seeing a swing back to full overlay for a reason. It provides more and easier accessed storage. And the view of the kitchen from a well used room is important.

    Cut somewhere else. You're nickel and diming things that you will regret losing, and it's not going to be a big difference long term.

  • 12 years ago

    It is a full overlay door style.
    I believe the flush finished plywood side is the $500 upgrade, versus $900 for the door style.
    It's all nickel and diming though, isn't it? :-) Those nickels and dimes add up fast. We cut all inserts, the more expensive door style I liked, cut backsplash to do later, cut labor to put on door hardware so we will do that ourselves, ect. ect.
    Good point about the applied door adding to the footprint for countertop... will need to consider that.
    And gooster's point about fading. I was thinking if it wasn't too hard to install ourselves, we could order the panels/decorative doors within a year or so. But maybe that is not a good idea.

  • 12 years ago

    I didn't see inset mentioned? An inset with vinyl sides? Agree with holly, no vinyl. Look at the next brand up in price may be a better deal particularly when doing paint. One that has dovetail standard. For instance I just checked my base semi brand. Standard dovetail, Blum ( soft close is an upgrade use it selectively, finished sides are NC, dimension charges are NC.

    In that 2 base end panels, 2 wall end panels, AND 2 cabinets prep for glass ( no matter how many doors). with veneer interiors total about $900. So for the cost of your upgrade to door panels you get the rest of your upgrade for free. The base price will be higher but the cabinet better. Flush ends and the veneer interiors come to 400. Of course you could just use the included finished ends (order some scribe to sneak under the molding on the sides)

    It can turn out that the better cabinet costs the same. Depends on how far down you are starting.

  • 12 years ago

    i did the flush finished ends. my cabinet budget was smaller than yours but not having that ridge thing and fake veneer on the ends that you can see were one of my main priorities. my builder cabs had the fake plasticy sides and they looked awful after about 5 years. the flush sides are so much nicer.

  • 12 years ago

    Buy plywood, cut and sand it, and finish it yourself. I'm using maple plywood to match my maple doors.

    If your cabs are painted you won't need to veneer the end. If they're stained you'll need a little veneer tape. It takes less than an hour to make a flush end sand and prime it. The maple plywood costs about $45 per 4'x8'x3/4" sheet.

    If you are unwilling to do this, ask your installer if he can do it.

    This post was edited by EAM44 on Fri, May 2, 14 at 17:48

  • 12 years ago

    $500-$900? You've taken your kitchen this far, don't go cheap on the finished ends. For that much more, it is not worth it to skimp, expensive as the units might be. Agree it will not only bring the rest down but will age differently.

    Sounds like a really pretty kitchen. Eat meat loaf and tuna casserole for a while, give up some expensive junk/fast food or a vacation, switch to Suave shampoo. But don't skip the finishing touches on your cabinets!

  • 12 years ago

    It is $0 for the vinyl skins, $500 for the 3/8th wood veneer end panels, $900 for the decorative door ends. I do feel like if we're going to do it, we might as well go all the way and get the decorative ends. Sounds like that is the group opinion as well. :-)

    ardcp, thanks for your imput. Our rental has the vinyl veneer too, and it is peeling/scuffed. That is what I fear, and why I know deep down inside I shouldn't skimp here.

    As far as other brands being a better deal, we are with a production-type builder, and can only use their venders, so we didn't have the choice to shop around. I know we are most likely paying more than with another brand, but it is what it is. The house and the land were a great deal, so I comfort myself with that. :-)

    Thank you for the advice so far.

  • 12 years ago

    lwo - i wish what you said was true here:( my medaliion silver-line lancaster with the upgrade to flush end but not apc was $8k, showplace was $12k, shiloh was $13k (and design had less drawers) diamond without apc was $10.5. for me since i really liked medallion, it made sense to upgrade the ends that i would see. i likes the idea of an all ply more custom cab but my budget made it not possible.
    i asked about moving to the medallion gold line but it was $1500 more and my kd said the construction would be the same unless i upgraded to apc. i do think the glides are better though.

Sponsored
Miller Woodworks
Average rating: 5 out of 5 stars23 Reviews
Franklin County's Trusted Custom Cabinetry Solutions