Software
Houzz Logo Print
sue_ct

Two sinks in one sink base?

18 years ago

This just occurred to me. I wanted a double under mount sink. I still wish I could have the large sink and a double, too though. I went with a 36" sink base because it was required for a double undermount sink,. Then, there is 3" on each side of the sink for spindles that I hope to have pull outs installed in, but if needed that actually allows 42" for the sink if the cabinet was notched out to allow use of the two 3" spaces on each side. Given that 42 inches, could I have the best of both worlds and fit a 24" (if they make one) or 30" single sink and a smaller rectangular prep sink next to it in the same sink base? I assume a support of some type would have to be added to sink base from front to back to support the edges of both sinks in the middle, but that shouldn't be too difficult or expensive to do should it? Or would that just be way to much sink in a small space?

Sue

Comments (6)

  • 18 years ago

    Sue,

    What sink are you currently planning on using? Some doubles don't need 36", some need more...it all depends on the size of your sink.

    We're getting a double undermount, actually 1-3/4, that does require a 36" sink base but has a much larger left bowl than the right. Sort of sounds like what you're trying for. The larger bowl isn't quite 24", it's only 21-3/8", but it's still pretty big for a double bowl sink.

    Ticor S405D, Undermount Sink, Italian Designed Stainless Steel 16-Gauge Double Bowl Kitchen Sink

    Dimensions:
    ...Overall: 35-1/8" x 20-7/8" x 9"
    ...Left Bowl: 21-3/8" x 18-3/4" x 9"
    ...Right Bowl: 10-1/2" x 15-7/8" x 7"

    Cost: $239.99

    (The S405DR has the bowls reversed)

    They both come with:
    * Template for Sink Cut Out
    * Mounting and Installation Brackets
    * 2 Rinse Sink Grids, one for each bowl (Polished 18/10 Stainless Steel wire bottom grid with opening for sink strainer)
    * 1 Pullout Basket Strainer
    * 1 Regular Strainer

    HTH!

  • 18 years ago

    I was going to go with 2 equal sinks. I don't know the brand, but she told me that most/all of the double sinks require the 36" sink base and basically have similar outside dimensions, they just play with the bowl size. So a 1 3/4 would have a larger sink and a smaller one but still have the same outside dimensions as the two equal size bowls. It really doesn't save any space or require a smaller sink base. I really struggled with this, because I wanted the double sink and spindles but didn't want to devote that much space to a sink base. I did a search after she told me that but could not come up with a double undermount that would actually fit in a 30" base. It would have had to have been either a drop in or an undermount single sink. It would not have helped to go to a 33" because that would only free up an additional 1.5 inches on each side of the sink, but going down to a 30" would have meant I could increase the cabinet sizes on each side of the sink by 3". I went with the larger sink base so I could get the double sink since it was holding up the cabinet order and I just needed to make a decision. It is already here, so I can't change it now. I still have the desire to have a large enough sink to sit a cookie sheet pan in AND have a good size second sink for prep, etc. My mother actually has the 1 1/2, but it is 15 yrs old and does not include a large side, just a standard size that is the same as one of the double size sinks that are equal, and one 1/2 that size. I don't like using it. I don't like using the small side for basically anything. As I said, though, it is older and not as large or as deep as current sinks, and not an undermount.

    Sue

  • 18 years ago

    I have the 405D noted above and my standard half sheet pans that I use for cookies DO lay flat in the bottom. That was my requirement as well.

    Also look at the Kohler shaped like the one linked below. It also has a very large sink, but the smaller sink isn't as big as the 405D's. It's also much pricier.

    Here is a link that might be useful: Kohler sink

  • 18 years ago

    If this is similar to what you're thinking of doing:

    {{!gwi}}

    Besides whether the required measurements fit or not, one main disadvantage I see is the center piece dividing the 2 sinks would be at counter level. If you have a faucet in the center and swing it back 'n forth while the water is running, think of what a mess you'd make outside the sink area.

  • 18 years ago

    I can't believe you found a picture of that! :) Great work! That is along the lines of what I was thinking of, just a larger prep sink. My problem with the equal doubles is that neither one is usually large enough for your large pans, like sheet pans, and the 1 3/4 has one that is large enough but the other is too small to be comfortable working in for me. I wanted the equivalent of the two equal size bowls, but remove one and make it larger. Don't make EITHER one smaller. Then you would have a large rectangular and a regular size rectangular. I don't think it works as well with the D shaped or too rounded sinks.

    Where did you find that photo? I guess it just goes to show that no idea is really new. :) I guess I would probably shut off or pause the water before swinging the faucet from one to the other. If anyone made the kind that kind of sink for extra large base cabinets, at decent prices, I would much rather have that than 2 different sinks. I do think it would work better. But I have looked at a lot of sinks online and never seen one. However, I have never seen what you found a picture of before, either. Anyone know if it is out there?

    Sue

  • 18 years ago

    Sue, I did a Google Images search and found that pic from a vendor. Here's the website: http://www.plumbingstore.com/frankesinks.html

    I use large pots and cookie sheets too. I find that you don't necessary need a large sink to wash them. A deep sink would do the job just as good and use a pull out water faucet for easy control when washing these.

    Good luck with your kitchen.