Software
Houzz Logo Print
illinigirl_gw

something bugging me about my cabinet design

13 years ago

So after looking at so many GW kitchen layouts I've come to notice something compared to my own design that's really bothering me. The sizes of 'standard' spaces. Let me give the examples:

Most GW'ers have 18" double trash pullout, my cabinetry designer says the smallest they can make them is 20"

Dishwasher- 24" standard on GW, mine is 26" wide
Ovens- 30" standard width on GW, mine is 32" wide

These are for frameless cabinets and it's a custom shop. What are they doing differently that adds these extra inches?

Thanks

Comments (18)

  • 13 years ago

    Are you talking about the appliances themselves, or the openings for the appliances?

    I've got 15" trash pull outs available, and that's for a framed line, which loses space for the faceframe. Your maker ought to be able to do a 12" trash pullout if you need to be able to go smaller.

    24" is for American sized DW's. Euro DW's are a fraction smaller. I'll always leave a 24" space, and order some trim to be applied if the customer has a Euro mode. It lets them change back to an American model down the road if they want to.

    Wall ovens are 30" from the outside to outside measurement. About 3" of that measurement overlaps the frame or filler panel of the cabinet that it's installed in. Even in frameless cabinets, if you have a fridge or other cabinets adjacent to the wall oven that will open against it, I'd put a 30" wall oven in a 33" cabinet. And maybe add a filler also, depending on what is adjacent to it.

    As far as what they are doing differently, maybe they aren't used to making frameless? Or they are sourcing their interior products from a different maker than the standards like Rev-A-Shelf or Hafele? You really have to have a conversation with your cabinet makers to find out though.

  • 13 years ago

    I believe I'm talking about the cabinet size itself. So the total width allotted for the appliance plus the cabinetry it's housed in.

    Sounds like the ovens are about right then at 32âÂÂ?

    How about the DW?

    I will ask next week about the trash. I know I can get a smaller single trash but if I want a double I was told 20âÂÂ.
    It is true they don't make a lot of frameless but they have made them.
    I'm on my phone now but I can post the layouts later today so you can see exactly what I am talking about.

  • 13 years ago

    My DW is a Bosch

  • 13 years ago

    LWO,

    Sorry for a side question .... but is it okay to have a 30" oven (Elux) in a 30" frameless cabinet?? Our oven cabinet is bumped out deeper than the adjacent cabs so the door swing should be less of an issue.

    Thanks,

    Carol

  • 13 years ago

    You can do a 30" oven in a 30" cabinet if it's the deepest cabinet, with no doors opening against it. If you have base cabinets opening against it, you'll want a filler there, or a hinge with a less than 90 opening. If you have a "wall of tall", it depends on what is opening against it with a tall door. If it's one of the new side opening ovens, it probably needs a filler. You've got to read the appliance specs themselves about the angles of the doors. And sometimes there has to be compromise because of the available space. It's a juggling act.

    If the DW is on an end with no cabinet to one side, it will need a filler and side panel, and that could be the dimension that you are seeing. Or, if it has a handle that projects, it could need additional spacing to have adjacent doors open against it and not damage the doors.

    There's a lot of adjustments needed to account for clearances of all kinds: appliances, hardware, corners, walls. It's not as simple as it seems. :)

  • 13 years ago

    I just wanted to add that a lot of layouts you see on GW aren't finalized layouts from a designer. They are preliminary layouts trying to get the major puzzle pieces in the right locations. Typically, they don't include all of the clearance accommodations and alterations that would be needed to be included in an actually installable and workable kitchen. Even when people "design their own" kitchens, they often don't understand about what actually can be done in some cabinet lines vs. others, or has to be done to actually be real world installed.

  • 13 years ago

    LWO,

    Thanks for the helpful posts.

    Carol

  • 13 years ago

    I just measured my DW and trash widths. My cabinets are frameless.

    The DW opening is 23 and 7/8ths inches between the outsides of the two adjacent cabinets.

    My trash is 17 inches in the interior. I have two front to back containers.

  • 13 years ago

    here are the examples:
    [img]

    [/img]

    [img]

    [/img]

  • 13 years ago

    Yes, it's like I said. The DW is on an end, so with the end panel and filler to support the countertop and finish off that run of cabinets, the overall dimension is 26". The opening itself should still be 24". The oven has more space around it than I would do with frameless. I'd have done 31", or even 30 1/2". Just barely have space showing beyond the oven frame. But, that's also a bit of a personal preference. What your designer did isn't wrong. Just different.

    It seems you have around 36" of unused space to the right of the ovens. Does that have a purpose or cabinetry planned for it?

  • 13 years ago

    I never noticed that much space between ovens and slider. That is a lot! What should I add?

  • 13 years ago

    What's to the left on the oven wall? I might consider flipping the design right to left, as I don't care for a tall cabinet blocking the vision when I enter a room via a major traffic pathway. That would give you space by the entry for some type of small appliance storage, or dish hutch, beverage center, or some other functional type of additional storage. Changing the depth and/or height of the counter and putting it in a secondary color could also work to keep the focal symmetry around the cooking zone. It all depends on what the clearances are to other elements, and what your personal use needs might be.

  • 13 years ago

    the main entry is actually to the left of the range wall, and the door you see on the right of the range wall is the dinette with slider out to the patio. Actually, now that I look at the overhead view I wonder if I can't add any more cabinetry towards the slider because of the dinette table clearance that I need.

    What do you think?

    [img]

    [/img]

  • 13 years ago

    sorry, i don't know why the photo is sideways, I rotated and saved it. let me try again:

    [img]

    [/img]

    Oh, how much would you allot for a 36 wide fridge? She's got 40" for mine, which seems wide. Even my own framed cabinets that I currently have are 39" wide to accomodate the 36" wide fridge? Seems like frameless would be even less.

    This post was edited by illinigirl on Sun, Nov 3, 13 at 15:01

  • 13 years ago

    I don't understand why they're putting so much wasted space in the design. Our cabs are frameless and custom like yours and they don't have all those fillers. Our island has 9' 9" of cabinetry in a little over 9' 10" of space, which include the end panel beside the DW at the edge. Our island cabs are 24" DW, 36" sink base, 24" DW, 15" trash compactor, 18" recycle pullout and it all fits under a 10' island which was the largest slab of caesarstone we could get.

    So not sure what your designer is doing? Seems to be just adding inches reflexively without bothering to be precise -- adding 2" to a recycle pullout is just odd ... and adding 4" to a fridge opening odder still. Maybe the fridge you chose needs some clearance on each side, but 4" is nuts. What do the fridge specs say?

    The appliance you select will have detailed specs that dictate the minimum cab cutout size. Our MW drawer is 24", fridge drawer also fits in 24", etc... you get the idea. So you should look up the specs of your appliances and check them yourself and if they don't mesh up with what she's doing then I'd be questioning her hard.

    The whole point of going with a custom shop is to make maximum use of your space and to get custom sizes wherever you want them. Something is very wrong here.

  • 13 years ago

    OK. Well I haven't told her the exact appliances yet. But I did say "30 inch double ovens" and "36 fridge" and "36 inch range".

    So maybe she'll nail down more precise after I choose? I will definitely ask this week.

  • 13 years ago

    Looks like you need the space by the slider for clearance for the dining area. If you need the storage, I bet a shallow pantry or utility cabinet about 12 in deep would work, or slightly deeper like 15-18 in for dishes and appliances?

  • 13 years ago

    On the elevations, it l appears the dimensions are to outside of boxes, which would account for the couple inch difference from the actual appliance clearance widths.

Sponsored
Hope Restoration & General Contracting
Average rating: 4.7 out of 5 stars35 Reviews
Columbus Design-Build, Kitchen & Bath Remodeling, Historic Renovations