Software
Houzz Logo Print
peggysugar

Tilt-out cabinet below sink - pull or no pull?

11 years ago

Hi - I am remodeling my kitchen and have a main sink and a prep sink. I've realized that I don't really want pulls on the two tilt-out drawers underneath my sinks (the ones where you can store sponges and such) as I think they will be annoying to lean against and may very well scratch against belt buckles and zippers. Since my cabinets are flush with one another (no frame showing), it will be really hard to open the tilt-outs without pulls unless I open an adjacent cabinet. Any ideas for a subtle, almost invisible pull that I can install for those two tilt-outs? I'm planning to install handles that you can grip all the way around on the other cabinets.

Thanks!

Comments (11)

  • 11 years ago

    Edge pulls might work there and be almost invisible under the counter edge. You do want SOMEthing.

  • 11 years ago

    Yep, I'd do an edge pull rather than nothing. Although, I'm not sure how pulls would be in the way while working at the sink. Your counter will overhang the cabinet fronts about 1.5" so I don't see how pulls could be in the way.

  • 11 years ago

    I have a pull on my tilt out and have never had that problem. How is a pull on a tilt out any different than the pull on the top drawer of a stack? What am I missing?

  • 11 years ago

    You might install a push to open hardware. There are magnetic latches that feature a push to open mechanism, they are simple to install and do not cost much. The magnetic latch would push the tilt drawer face open just enough to allow you to get the drawer face open.

    Here is a link that might be useful: Top Quality Cabinets

  • 11 years ago

    I'm interested to see what the responses are here. I tend to lean against the sink while I'm doing dishes and have wondering whether having hardware (even on a faux drawer) would be annoying.

  • 11 years ago

    So, you're in and out of the fold out, often with wet hands. Which will eventually, without hdw. affect the finish.

    So, why not a longer handle similar to those used on refer. doors, which dive into the front on the ends, thus eliminating the snag issue, and provide a convenient place to hang a dish towel, for those wet hands.

  • 11 years ago

    Follow up - thanks for all the suggestions. I think the issue is the leaning against the sink while doing dishes..belt buckles and zippers will scratch the handle, or perhaps the handle will get in the way or just feel like an obstruction. My sister-in-law has a handle on her tilt-out drawer and says it's no problem, but she has a 1 inch overhang of counter. My overhang is not that big. I'm considering a finger-pull for just the tilt-outs. It'll be barely visible but will allow me to open it. I'm buying enough traditional pulls in case I change my mind!

  • 11 years ago

    Visually I wouldn't like having two pulls that are so different on the cabinets. I have pulls on my tilt outs and I lean into the sink and I do not even notice that they are there. As far as scratching goes, mine are stainless and do not scratch at all....not even slightly. But you can always just buy a couple of extra in case you need to replace them.

  • 11 years ago

    I have two cup pulls on my fake drawers under my kitchen sink and my master bathroom sink. I never notice them when at either sink. They are cheap brushed SS hardware at only $1.67 each and don't have a single scratch.

  • 11 years ago

    i have a fullsize pull on mine and i never even notice it i had to look up just now to make sure it was there .

  • 11 years ago

    I have 1 pull on my tilt out on a 27 1/4 inch sink base cabinet. My overhang is less than 1 inch. It does not get in the way at all. I don't even notice it there. If it did I would rather me hit the pull instead of the cabinet front. My thoughts were it easier to replace a scratched pull if in fact it even scratches than leaning against my cabinet and scratching the cabinet front.