Software
Houzz Logo Print
greasetrap_gw

Resin Cleaner Recommendations

11 years ago

I've been using my softener to remove iron from my water, and I recently found out (via an earlier post on GW) that there's way too much iron in my water for this method to work well in the long run. I've just started to notice some iron staining towards the end of a cycle.

Until I can get my filtration issues sorted out (I think I'd like to get a Filox filter installed), I'd like to try to clean the resin in the filter as much as possible. Up till now, the only thing I've been doing is adding the rust-removing salt to the brine tank.

Are there any products that you would recommend for this? I found a product called ResCare on Amazon that seems to get very good reviews, as long as you add the product manually between regenerations. There's an auto-fill product as well (which wicks into the tank automatically), but people say this is too complicated and doesn't work well if your system regenerates based on actual usage.

Also, would it make sense to add Iron Out to the brine tank? I assume this is already included in the salt that I'm using.

Thanks for your help.



Comments (4)

  • 11 years ago

    The salt that you are using contains phosphoric acid, the same ingredient in the ResCare. Iron Out contains sodium hydrosulfite and sodium metabisulfite. The two products work differently. Phosphoric acid reacts with the "sticky" iron oxide to form ferric phosphate which is easily rinsed away. Sodium sulfite/metabisulfite react with the iron oxide to form ferrous iron, which stays in solution to be rinsed away.

    With fouled resin, the best option is a Resup treatment to remove the surface "macro" fouling, followed by an IronOut treatment for the internal "micro" fouling. The procedure is time consuming, but it will restore your resin as much as is possible:

    1. Pour 1/2 C of the Resup
      into the brine well in your brine tank. Force your softener into a manual
      regen and let it go all the way through the regen.
    2. Now,
      we try to address the iron in the center of your resin beads. After the resup
      treatments, bypass the softener and allow to sit for 24 hours to form a strong
      brine.
    3. Dissolve one cup of Iron Out in 2 gallons lukewarm water. Pour this into the
      brine well in your brine tank. Place your softener into a manual regen and stay right there.
    4. When the backwash is complete, it will move to the brine/slow
      rinse mode. When the softener enters step two and starts drawing brine, pay
      attention to the way it sounds. The sound will change
      when there is no more brine to draw.
    5. Now, we want the iron out to sit in your
      softener for 12 hours (once resin has iron in it, it takes time to get it back
      out). Rapidly push the button to advance to the next regen step, then the next, then
      back to service mode.
    6. Now, bypass your softener so no water goes through it and
      allow it to sit for 12 hours. Add 5 gallons of water to your brine tank
      manually.
    7. When 12 hours have passed (longer won't hurt if scheduling is an
      issue), open the valves to allow water to the softener and force another manual
      regen - allow it to complete the regen normally. Wait 24 hours and repeat.
    8. Once every couple of months, repeat steps 3-7, but only let it soak for an
      hour instead of 12. No need to do it twice in a row after this initial
      treatment - once will do.
  • 11 years ago

    Thanks for the detailed instructions. I have a few additional questions:


    - If there's already phosphoric acid in the salt, will the ResCare be of much additional help?

    - Should the ResCare simply be poured into the brine tank, or down the tube? I read somewhere that pouring it into the tube, gets it down directly into the water.

    - Do I need to leave the softener on bypass while the brine is concentrating? We have so much iron in our water, that it's really not realistic to use the water while the system is bypassed?

    - It takes my system over 2 hours to regen. Do you know approximately how long it would take before the brine is drawn down?

    - My system has dials instead of buttons. Here's a picture:


    How do I advance to the next part of the cycle? Could I simply unplug the softener, wait the 12 hours and then plug it back in?

    - It may take a while until I can get everyone out of the house for 14+ hours to do the full Iron Out treatment. In the meantime, would it help to put some Iron Out in the brine tank on a night before the system regens?


    On a related note, do you know what the flow rate is for a Filox filter? I have a 15 gpm well pump. Would I need 1 or 2 filox filters to get a 10 - 15 gpm flow rate?



  • 11 years ago
    1. Will ResCare do any good: Yes - you will have a stronger concentration.
    2. Brine tank or brine well (tube): Down the brine well
    3. Bypass while waiting for brine: No - I was making modifications to the instructions and missed that. Sorry. No need to bypass while waiting for a strong brine.
    4. How long to draw brine: 10-20 minutes (bring a book to read ;)
    5. Dial control: I didn't have time to go back and read your previous thread, forgot you had a dial control. Yes, wait until the brine is all drawn in, then bypass and unplug.
    6. Iron Out prior to full treatment: Yes - 1/2 cup, dissolved, poured into the brine well

    Service flow rate on Filox is 6 gpm/cubic ft. Backwash flow rate required is 12-15 gpm/SQUARE ft. A 2.5 cuft system (13" diameter) would provide you with up to 15 gpm service flow and would require 12-14 gpm backwash flow rate. That would be the largest size your well could accommodate.

  • 11 years ago

    Thanks a lot. That's really helpful. I just ordered the ResCare and Iron Out.

    On a related note, my filter company didn't recommend a chlorinator for iron removal, as they said it would be messy to mix up, and difficult to keep calibrated correctly. I was just reading about a dry pellet system though, which installs over the well pipe and drops pellets in the well as the pump runs. This would be followed by a carbon filter indoors. What do you think about this type of system? My biggest concern would be that it might be difficult to change the pellet bottles in the middle of winter.