Software
Houzz Logo Print
hzdeleted_5845483

Lawnmower recoil pulls rather hard

11 years ago


And occasionally will pull my arm back. I did some reading and saw
that I could have a sheered flywheel key. Well I checked it out this
a.m. and first when taking off the engine shroud i noticed that one of
the back bolt holds was tore and so the shroud is no longer secured to
the engine in that corner. I have also in the past had the recoil rivets
come loose and had to rerivet them. Anyway- I checked out the key and
didn't look sheered and maybe moved and slightly damaged a bit but
nothing too bad by the looks of it. I received this mower from my
grandmother with it being a few years old then and shortly after my wife
hit a stump and blew out the blade adapter, maybe this damaged the
key?!?

That being said the mower runs fine, leaks no oil, it's just simply
hard on the shoulder and sometimes it will just decide not to start.

So question is, could the recoil not be sitting in the flywheel (cup)
good enough and that could be contributing to the hard pulls/starts or
do I have a flywheel key problem? Lastly should I start looking for a
new engine shroud piece then too or is that corner not being bolted down
not something to worry about? I'm wondering if it tore because of how
hard it is too pull sometimes.

Any advice would be so greatly appreciated as my wife and I are penny
pinching right now for a kid so if I can avoid taking this to the shop
that would be great!
it's a 7 hp briggs on a Husqvarna



Comments (7)

  • 11 years ago

    Timing will be advanced 5 degrees or more with that partially sheared key. That's enough to cause significant kickback. As previous post says replace the key and make sure you tighten the flywheel nut to specified torque. (usually 65 fl/lbs). As for shroud, replacement is 493293 can costs about $50 without recoil started. You have to drill the rivets out and then bolt up the old starter on your new shroud. You can probably do better using Ebay or a mower shop which has a boneyard and will sell you the shroud second hand.


    User thanked Greg Goyeneche
  • 11 years ago

    Thanks to both of you! I have ordered a new key and will try that later today. ggoyeneche, you mentioned the replacement shroud being part #493293 but I found it to be #499677, do I have it wrong? I'm trying to find a used one on ebay or CL as you mentioned they are expensive! I've actually found this shroud to be junk as I've already had several of the rivets on the recoil break loose along with the rivets on the side engine identification tag...


  • 11 years ago
    last modified: 11 years ago

    Well i got her back together and running. After putting it back together, the engine was surging.....so i went and picked up a new spark plug and that took care of the surging. As for the shroud I was able to bend the broken tab (bolt hole) back some and then added a washer to that bolt. Seems to be holding for now, but I would definitely still like to replace it if I find one for a reasonable price. Engine still seems to pull harder than some but I'm thinking it's cause it's a 7 HP engine?

    So next question is: It seems like my engine makes a bit of a rattle (it's been doing this for awhile and normally I can pull on the recoil cord some and could get the rattle/vibration to go away. Well it's still doing this and sometimes I can make it go away if I press on the top of the plastic engine cover, however neither of my "fixes" seem to be working that much anymore.

    Could this be something as simple as the recoil being bad? I don't know if it's related or not but the little metal tab that is suppose to stop the recoil at the engine is up the recoil rope probably a foot higher then the engine. I can add a pic if that helps :)

    Again, thanks so much for the help!

  • 11 years ago

    Anyone still there?

  • 11 years ago

    this appears to be the overhead valve 121602 or similar model. The engine is sensitive to correct valve adjustment. When there is excessive valve clearance, the compression increases. There is also the possibility the compression release device has failed.

    if the shroud is broken, call the local mower shops to see is a used assembly is available. Keep a record of the original engine numbers.

  • 11 years ago

    Okay, I adjusted the valves, seems to be a bit better but still pulls over nothing like the OHV 6.5 hp I picked up for parts. Could the starter contribute to this? In regards to the compression release device failing, isn't a way to test that when finding Top Dead Center, right before that the intake valve will open a bit?


    Also, I did end up picking up a used shroud as that's why I bought that used mower as I spent as much on that as I could find a used shroud for!


    Thanks for your help on this!