Software
Houzz Logo Print
scottmccarthy30

Craftsman tractor/mower won't start

11 years ago
last modified: 11 years ago

I have an old craftsman tractor/mower that was refurbished 2 years ago. I turn the key and nothing happens. It has fired without problem every time thus far. But today, nothing. I connected the battery to my car battery (car off) and still nothing. Any ideas?

Sears model 502.255290

(Like I said, old tractor)

Comments (9)

  • 11 years ago

    The "502" in the model number identifies it as a Murray product. Murray went belly up a few years back, and I believe I heard that the remains of the company was bought by Briggs and Stratton. Depending on just how old the tractor is, there might not BE any safety switches. I would start by removing the battery ground cable, cleaning both ends of it, then remove and clean the ends of the positive (+) cable. While you have the battery disconnected take it to an auto parts house and ask them to test it; if it's okay, give it a good charge, and if it doesn't test good buy a new one. Put the battery back in place, then reinstall the positive cable, making sure that you get good, tight connections on both ends, and then do the same with the negative (-, or ground) cable. If that doesn't cure the problem, report back with the model and serial number of the engine.


    scottmccarthy30 thanked javert
  • 11 years ago

    I won't have a chance to work on it again, but I did pull and test the battery, it came back "good" with a 50% charge. I placed it on the charger. I suspected the culprit may be the switch that makes sure the brake is depressed. I'm not entirely certain how to test it or bypass it. But I'll be back once I've had a chance to get the battery back in and try again.

  • 11 years ago

    I don't know specifics about your mower, but on mine the brake switch is closed (i.e. continuity between the two contacts) when the brake is engaged. But, on mine, the transmission must be in neutral and the cutting blades disengaged. In other words, make sure transmission is in neutral and the blades are NOT engaged; unplug the connector at the switch, and there should be continuity between the poles on the switch ONLY IF THE BRAKE PEDAL IS DEPRESSED. ****DISCLAIMER: I don't know for sure if this is the way your's works, but logic tells me that it probably is.


    scottmccarthy30 thanked javert
  • 11 years ago

    "I connected the battery to my car battery (car off) and still nothing. Any ideas?"

    Yes, jump directly to the starter from your car thus bypassing all safety and other switches. You don't give your engine model number and I do not do look ups from Craftsman numbers.

    Walt Conner


    scottmccarthy30 thanked tinkerer200
  • 11 years ago

    I worked for the Briggs/Murray distributor, we had no lookups for the 502 series as it was old Murray-Ohio. Most parts are obsolete anyway.
    Walt's suggestion will tell you if the starter works. If good you need to start working through the interlock system. With a 12v test light check for power at the small terminal on the solenoid with the key in the start position and work from there.


    scottmccarthy30 thanked romore_gw
  • 11 years ago
    last modified: 11 years ago

    I checked the fuse. Battery is charged. And I'm still SOL. Currently trying to find the limit switches so I can bypass them. Here is a wiring diagram from the manual

  • 11 years ago

    I never found the second limit switch, but I jumper from the back if the key switch to the solenoid, thus bypassing both switches. Mower starts. Switch that checks for blades off had already been bypassed, so I just removed it anyway. Thanks for everyone's help. I'll just make sure my foot is in the brake when I start it. Wouldn't have figured it out without all the help from the forum

  • 11 years ago

    seat sw


Sponsored