Software
Houzz Logo Print
jmc1010ku

Is this Subway Tile pattern acceptable?

10 years ago

We specified centered symmetrical brick pattern in the bathroom shower and assumed they would do the same in the kitchen. Instead, the installer used a 2.5" offset for 12" subway tile. We have a galley kitchen and the opposite side has a 3.75" offset which is already grouted. We didn't catch the mistake in time and think they need to redo it. Is this acceptable or should they redo it?


Comments (27)

  • 10 years ago

    I really like it!!!!!!

    JC thanked User
  • 10 years ago

    What does the other side look like? Would that be acceptable to you? But neither is centred symmetrical brick pattern as far I my knowledge goes...

    JC thanked akl_vdb
  • 10 years ago

    I'd want it to match - pretty countertop!

    JC thanked romy718
  • 10 years ago

    Oh I hate to say this, but I am really concerned with that. Having a galley kitchen where the backsplash on either side didn't match would send me to the loony bin. Also, it looks like there is going to be a tiny sliver of a tile now just to the right of where they left off before the upper cabinet. I'm so sorry JC, but I'd say redo.

    JC thanked rebunky
  • 10 years ago

    Do you have a contract? What does it specify for the kitchen? Both sides of the galley should match, but even If they redo one side, you won't get what you want. As a negotiation point, I would start with, "we specified running bond with this tile" and ask them to redo the entire kitchen. See what they say.

    JC thanked eam44
  • 10 years ago

    Sides need to match, in my opinion.

    JC thanked kelleg69
  • 10 years ago

    I like the 2.5" offset on the 12" tile -- BUT it needs to match the other side. Also I'm surprised that any tile installer would install the tile that way without someone telling them to do so.

    JC thanked User
  • 10 years ago

    Thank you all for the comments! We will ask to redo this side to match the other side at 3.75". The larger offset looks much better.

  • 10 years ago

    Without a written contract you may have a tough time getting them to redo anything. Good luck!

  • 10 years ago

    I think that is extraordinarily strange that they would not make it match the other side. Glad they are going to fix it as it is obviously their error.

  • 10 years ago

    match - it has to! but I do like the offset as opposed to just the running bond - I think it "updates" the subway tile, and offers some flair on a more plain tile.

  • 10 years ago

    I think it looks nice but it should match the other side.

  • 10 years ago

    Seriously, you need a contract that specifies that both sides should have matching offset???

    Seems to me to so completely obvious that it's understood that tile installation in walls in the same room needs to match.

  • PRO
    10 years ago

    Since the zigzag line is the dominant element, it should probably be centered on the faucet.

  • 10 years ago
    last modified: 10 years ago

    I'm with nosoccermom. How many of your contracts specified that tile offset should match, on each wall in a kitchen (or bathroom?)

  • 10 years ago
    last modified: 10 years ago

    The contract usually specifies that the tile will be laid in a running bond or other pattern, and it specifies the offset. That way you don't have to state that the tile on either side of the room should match. I'm not sure why this is unclear but I hope that helps. If the original poster doesn't have a contract, that makes it much harder to deal with these sorts of things.

  • 10 years ago

    None of my contracts have specified the tile pattern. My gc told me I could change my mind about the pattern up until he ordered the tile, which was usually about a week before tiling. He checked in with me then and I confirmed the pattern.


    I do not think a contract should have to specify that the tile pattern must be the same on both sides of a kitchen. I would agree that it might be hard to argue that tile was set incorrectly just because the pattern was wrong if there is no pattern stated in the contract . But mismatched is entirely different in my view!

  • PRO
    10 years ago

    Its a pattern sometimes called a Dutch Bond. It's more used in Europe than here, but it is an known pattern. Whether it is acceptable is up to you is your decision. I think it has a lot of personality and is different enough to be noticed, but no so different as to be strange.

  • 10 years ago

    Like it, but it has to match the other side. :(

  • 10 years ago

    I don't care for the offset. I want to nudge it over to center.

    Who doesn't know that both sides of the galley should match? Only someone totally asleep on the job. Having to put it in a contract is like saying all four walls in a room should have the same paint finish. Judge Judy would laugh them out of court.

  • 10 years ago

    OP here. This seems like a ridiculous technique to me, but the offset was NOT measured (it is a result of the overall wall length). The last tile piece of the first row had 2.5" chopped off on the end to fit. Then a full new piece was started above the cut piece which resulted in a 2.5" offset. The same technique was used on the other side, but 3.75" offset was the result due to the walls being different lengths. We have a contract, but only states "install backsplash. any design is included" and we verbally agreed on the same design as the bathroom which is running bond.

    Hopefully we won't have to see judge judy :)


  • 10 years ago

    It should be at least 1/3 offset, so the 3.75" may be ok.

  • 10 years ago

    I think it absolutely should match the other side. I also think it's strange that they would not come to you for the OK to do anything other than the standard running bond IMO.

  • 10 years ago
    last modified: 10 years ago

    Well if you agreed on running bond, why not ask for it to be running bond? If that's what you discussed, that's what you should get, don't you think? See what they say. You can always compromise to the 3.75" offset if you must.

  • PRO
    10 years ago
    last modified: 10 years ago

    Ah-ha! I knew I had seen this pattern illustrated somewhere. Apparently in tile work this is called an Offset Pattern.

    For those interested, Emser tile has a nice .pdf on types of tile patterns.

    If you verbally agreed on a running bond, then that's what you should have. This cannot possibly be construed as a running bond pattern. If your contractor is worth his or her salt, he or she will agree to redo this work.

    This time, tell the installer to start in the center and work outward toward both side to ensure the pattern is centered. That's what the tile installation standards call for. Evidently it was not done in this case, so for that reason along, it should be redone.

  • 10 years ago

    As others have indicated, it's a cool pattern, but it needs to match the other side.

Sponsored
Mary Shipley Interiors
Average rating: 4.8 out of 5 stars34 Reviews
Columbus OH Premier Interior Designer 10x Best of Houzz