Software
Houzz Logo Print
denbigh97

Leaky shut off valve bleeder cap

10 years ago

I had both an outside hosebib and shut off valve replaced with 1/4 turn ball valves by a local plumber in early winter. I did not turn them on since the replacement. I turned them on for the first time last night and noticed the small bleeder valve on the shut off valve has a small leak. I tightened it as much as I could with my fingers, but it still beads a bit when the valve is open. It doesn't leak at all when the valve is closed. The same plumbing company wants $100 to come out and fix this issue! How do you fix this? Is it simply just loosen the bleeder cap and replace a washer? or am I looking at replacing the whole shut off valve again (and re-sweat the pipe)?
The bleeder that I'm talking about is below (stock picture):

Thanks!!

Comments (19)

  • 10 years ago

    "The same plumbing company wants $100 to come out and fix this issue! "

    Get a rope!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

    Take the cap with you ( it doesn't leak while it's off anyhow) as you pass hardware and big box stores. Find valve off the shelf that cap fit's and buy whole valve for 6 bucks then trash everything besides cap. Plan B. Take cap into auto parts store to buy 1 foot of fuel hose that snuggly slip's inside cap. Might require more than a couple attempts but squarely slice off a piece to replace gasket. Plan C. Buy a nice fat O-ring at auto parts. Plan D. Call plumbing company and tell them they are greedy rip off artists and you think it suck's they didn't tell a customer what Klem did for free,,,,,,,,,,,,,unless they admit to being that #*^% stupid.

  • 10 years ago
    last modified: 10 years ago

    C can work. its basically an o-ring or tiny washer. Since it's new, it may be missing.

    BTW: there is a direction thing about this valve. It needs to be installed such that the little cap thingy is toward the hose bib so that when you turn off the valve, you can remove the cap and the water will drain out the hose bib. Put it on the other side and it will always be pressurized. Guess what the previous owner did in my house?

  • 10 years ago

    "Guess what the previous owner did in my house?"

    Don't bet on it weedy,might have been OP's plumber installed it.

  • 10 years ago
    last modified: 10 years ago

    It's been said misery love's company,check out another thread titled " Water temp fluxations" to see plumber ripping off consumer.

  • 10 years ago
    last modified: 10 years ago

    The bleeder cap ended up being stuck. Due to the poor access to the valve (located in ceiling of my fully furnished basement only through a 1'x2' hole with other pipes around it) and the inability to get leverage, I ended up hiring another plumber. It turns out the first idiot plumber sweated the valve while the bleeder cap was on, thereby melting the rubber gasket inside which made it impossible for me to remove by myself. 15 minutes and $80 deductable later, leak fixed.

  • 9 years ago

    You can buy replacement bleeder caps with washer for $2 online or har Sears

  • 7 years ago

    trying to find these screws and am not able to find them. Home Depot did not have them. Maybe a plumbing supply> They should be pretty simple to located and replace.

  • 7 years ago

    I couldn’t find the bleeder screw anywhere, and didn’t want to drive around town (and waste gas) to look for it. So ended up buying a new valve for $5 from Home Depot and cannibalized it for the screw.

  • 7 years ago

    I haven't expressed my opinion lately of plumbers. I've dealt with hundreds of plumbers and 95% chase cars and lick themselves in places respectable folks don't even scratch in public.

  • 7 years ago

    Not a screw, a cap. I had one go bad on me recently and found HD (or Lowes) had a bag of them for a few bucks, different sizes.

  • 7 years ago
    I will check out Lowes,. Home Depot had nothing like that at all. They acted like they did not exist as an item you could buy. thanks. How much was the bag?
  • 7 years ago

    Maybe $5? there were maybe 3 in the bag, only one fit.

  • 7 years ago

    I've been in building maintenance for decades and have never been able to buy valve parts from big box stores. Below is link to valves that can be cannibalized for a cap. Please post link to Home Depot or Lowes bag of bleeder caps.

    Valves

  • 7 years ago
    last modified: 7 years ago

    I just bought a package of 3 bleeder caps, varied sizes, in HD today. $2. A helpful employee found them after a bit of searching. They were by the valves. Two Qs: (1) Should the cap seal by just hand tightening, or do I need to use pliers? (2) There are three gaskets, how does one determine which one to use? Should it be tight enough that I have to push it in to seat it in the cap? Thanks.

  • 6 years ago

    That's the hardest part...finding a cooperative employee!

  • PRO
    6 years ago

    Dab some of this on the male please.

  • 5 years ago

    "Zelares" is a stubborn spammer. Please flag."

    All three times he has posted? If that's as bad as we ever see,we should be content.

  • 5 years ago

    Klem, the bot keeps coming back again and again. I'll bet it's posted spam a dozen times over months, just doesn't show in activity.