Software
Houzz Logo Print
hzdeleted_22590553

Zipper foot too low!?

10 years ago
last modified: 10 years ago

I don't know why I bother to sew. I lost the zipper foot for my machine so last time I made pillows I borrowed a machine, used a regular zipper foot, and made it work. This time I thought I'd do it 'right' and went to a sewing store and bought a concealed zipper foot for my machine. I have a Brother VX-1100 that was given to me years back and usually sits in a closet. The friendly elderly man hooked me up with a Singer Low Zipper Concealed foot. Since I had my machine along he popped it on and even double checked verbally by asking a lady there. I wasn't paying too close attention other than I saw it fit. I assumed it was fine and I'd figure anything else out later. This wasn't a JoAnn Fabrics, but a specialty sewing store. Finally got it out tonight and it fits, but even pushed up and tightened as far as I know to make it go there's hardly room to actually put the fabric and zipper underneath. Is this normal?! Is there something else I can do with this machine before heading back to the store? Unless I start at the end of the zipper and run the teeth straight under the foot, I can't fit the fabric and teeth if I try and slide it underneath. Hope that makes sense.

On a mission, I decided to try and make it work. I, somehow, just managed to sew the zipper leaving the top end OFF the fabric instead of the end that's too long and needs cut. I'm not sure how I managed to do that. Can't wait to get my seam ripper out tomorrow. Grr.

This is up.

Showing the regular foot beside.

Awesome.

Comments (35)

  • 10 years ago

    I'm not sure I understand, but if you got the zipper in, it doesn't matter that it's too long at the top...just slide the zipper head below the waist seam and cut the top tabs off after you sew on the waist band. The zipper head won't be able to come off.

    I've shortened zippers on both the top and the bottom at various times and find it much easier to put longer zippers in as I can slide the zipper head out of the way while I sew.

  • 10 years ago

    Sorry, there are two issues here. The main one being that the zipper foot is is very low. There doesn't seem to be enough room for the fabric and zipper to slide underneath. I think there should be more space. There doesn't seem to be enough clearance and it looks like there's more than what there is. Seriously the only way I could sew the zipper was to start at the bottom of the zipper (not at the head part - I had to really force the fabric and teeth underneath and it jammed up) and slide the teeth straight down to where I wanted to start.

    .just slide the zipper head below the waist seam and cut the top tabs off after you sew on the waist band

    I might not be awake enough to process this. Sounds like I don't need to remove the zipper? This is actually a pillow.

  • 10 years ago

    Are you sure that is a zipper foot? Here's what mine looks like, it's made to hold fabric and zipper on one side while you sew.


    shortening a zipper from the closed end may solve your problem. I just place the zipper to fit and sew over the teeth a few times to make a new stopping place. There are probably more correct ways but, it works for me.


  • 10 years ago

    A "concealed zipper" foot would be for installing Invisible Zippers (brand name) and they are different than a regular zipper. Also a Singer foot probably won't work on a Brother machine because the shanks (where the foot attaches) are different lengths. A regular zipper foot should be narrow and have the ability to be switched from one side of the needle to the other so you have the foot pressing on the side away from the zipper.

    Annie is right, though...if the zipper needs shortening, slide the pull tab down and sew through the zipper and fabric near the ends of the zipper several times to create a new stop, then trim off the long ends.

    Donna

  • 10 years ago

    Like msmeow said, if the foot you are using won't raise high enough to get your materials under, the guy probably sold you the wrong foot for your machine. Although you expect someone at a sewing machine store to know, he may only have knowledge of the motor part of the machine, not a clue about actual sewing.

  • 10 years ago

    I agree with maddielee. You need a zipper foot made for your particular machine and not a Singer foot. The feet for each brand of sewing machine are different, and are not usually interchangeable.

  • 10 years ago
    last modified: 10 years ago

    The one on my machine is a concealed zipper for invisible zippers which is what I wanted. I probably should have been specific in my post title.

    I also thought I needed the same brand for it to work but they acted like this one would also. I guess I'll start by calling them tomorrow. Thinking more, I'm sure it was well over a month ago I was in there. I'm not even sure I still have the receipt. At least the piece wasn't expensive I suppose. I think I'm more annoyed by the new set back time than anything. Lots of set backs with a little project that should be simple! If they don't have one that works hopefully I can find one online.

    Maddie & Msmeow - So even though the zipper is sewn in place and the zipper head is sticking out past the fabric, I can unzip and cut it down? Am I understanding that right?

    And here I just found one on Etsy for less than I paid there. The whole reason I went to the sewing store was to avoid getting the wrong thing. I also needed extra bobbins. Hopefully they'll work. Come to think of it, they sell a bunch of sewing machine brands, but I don't know if I saw Brother in there.

    Concealed zipper foot

    ETA - I now remember I didn't want to order one online because all the ones I found were snap on like in the link and I don't know what it's suppose to hook to. If I remove the concealed zipper foot that's there, there's just that straight metal piece (that I'm sure has a correct name) and no groove or anything at the bottom to hook onto. ?

  • 10 years ago

    Here's some info (it's really easy) Shortening a zipper from the bottom or top

  • 10 years ago

    I'd bring the machine and the foot and the project in. They should make this right so you have what you need. It shouldn't be hard at all.

  • 10 years ago

    I have a Brother sewing machine and just got this invisible zipper foot from Amazon. It's all metal - no plastic, and works perfectly. When I ordered mine it was eligible for Prime shipping or was an add on item, I don't remember which. But I got it in a few days.


    https://smile.amazon.com/gp/product/B003AJZXPA/ref=oh_aui_search_detailpage?ie=UTF8&psc=1



  • 10 years ago

    Are you using the presser foot lift to raise the foot and place the fabric with zipper under th foot? There are generic feet to fit most machines. They come in low shank, high shank and slant. Your machine appears to take a low shank foot, which appears to be the type of foot you bought.

  • 10 years ago
    last modified: 10 years ago

    Ah, thanks for the link Maddie!

    Thanks for the link and info Terriks. I still can't figure out what that straight bar of the clip on feet are supposed to attach to on my machine. I don't see anything to click/lock it on. Being that inexpensive though I could give it a try!

    Blubird - Yes, actually the photos I posted above are with the foot raised completely up.

    I can't find the receipt, but I still have the bag with their logo and business card stuff so hopefully they'll be ok. I'll take everything along when I go.

    On a good note, I found the few accessories that came with my machine and I do have a regular zipper foot. Not ideal if you don't wan the zipper showing, but it's nice to know I do have one!

  • 10 years ago

    Maybe you could just try using your regular zipper foot. Here are a couple of instructions showing how to use a regular zipper foot to put in an invisible zipper:


    http://blog.sewserendipity.com/2009/08/dont-fear-invisible-zipper.html


    http://www.burdastyle.com/techniques/how-to-insert-an-invisible-zipper-without-an-invisible-zipper-foot

  • 10 years ago

    what happens when you put your regular foot back on? Does it lift up any higher? If it doesn't lift up any higher with the regular foot on, there's another issue, not the foot. Sometimes when thread gets wrapped around the take-up lever, it inhibits the lift.

  • PRO
    10 years ago
    last modified: 10 years ago



    Sheesback, I have six machines, one of them is a relatively newer model Brother. The zipper foot attachment for that machine looks like the photo below. It clicks on. You do NOT need a special concealed zipper foot to sew on a concealed zipper. If you have an older Brother, the zipper foot would look like the photo that maddielee sent you.

    You’re using the wrong type of zipper if you don’t want the zipper coils to show. You need an invisible zipper for that, and an invisible zipper can be installed with a standard zipper foot. Follow the instructions on the package for the concealed zipper, and iron down both sides of the coils with an iron set at medium setting. I install invisible zippers in all of the pillow covers I make for my clients. It’s really easy to do, with a standard zipper foot, provided that the zipper has been prepared properly by ironing.

    I could possibly even send you a link showing you in pictures how to iron the zipper so you can sew it with a standard zipper foot, if you think you need it. Let me know.

  • PRO
    10 years ago

    Here’s the link I was talking about. It’s super easyHow to sew a concealed zipper with standard zipper foot

  • 10 years ago

    I have always had issues with the top part of the zipper, it doesn't matter concealed or not it just has never been easy.

  • PRO
    10 years ago

    Another tip for sewing invisible zippers on pillow covers - after installing the piping, I always sew on the invisible zipper before sewing any of the other seams. Using a 20” invisible zipper, I start at the top of the zipper, on both sides, lining it up with the edge of the fabric. If the zipper is too long for the cover, (perhaps an 18 x 18 or less cover), after both sides of the zipper have been sewn, I pull up the zipper slide half way up the zipper and cut off the remaining unused portion of the tail at the bottom. Sew reinforcement stitching several times over the cut portion to create a new stop for the slide. Even though I sew covers of varying sizes, I buy 20” invisible zippers in bulk, and use them for any size cover.

  • PRO
    10 years ago

    I did even further research, and this is the photo that I turned up that’s supposed to fit a Brother VX100, not the other one I posted. It’s like the photo maddielee posted, as I said earlier, due to it’’s older age. Here’s the link to it:http://sewingpartsonline.com

  • 10 years ago
    last modified: 10 years ago

    Terriks - Thank you! I will go over them later today when I attempt to tackle this again.

    Blubird - The regular foot lifts up much higher and is perfectly fine. I was surprised how low the new (apparently wrong) concealed zipper foot is.

    Heidesign - Yes, I don't have it in front of me, but I'm pretty sure the zipper foot I found yesterday that went with the machine looks like the one you and Maddie posted.

    All the zippers I bought say Invisible zipper. They're these ones.

    The pillows I made a few years ago when I borrowed another machine and used a regular zipper foot, I can still see a tiny edge of the invisible zippers and I did iron the zipper/teeth, so I'll definitely be looking at all the info and tutorials linked and am glad to know I can get rid of that this time around without needing a special foot.

    That is a good idea to buy a longer zipper that way you always have one that covers the full length of the pillow case.

    Actually my machine is a VX-1100. I'm not sure that was a typo since I see they make both models. Too many model numbers! When I type in my model number on that site and a list of products come up I don't see that foot you posted, but there is a Teflon Zipper Foot, Low Shank in the list. Can't remember which one, but one site I was on yesterday I did find a standard zipper foot for my machine, but then like I said I found the foot that came with it. Also found some type of flat plastic plate thing. I think it's for buttons maybe. ? I don't know. I have the manual if I ever feel like trying it out!

    Thank you everyone! I'll report back!

  • PRO
    10 years ago

    Shee, I made a typo and meant to type VX1100. If you go to the link I posted for sewing machine parts, just type in "Brother VX1100 zipper foot” into the search box, and it will take you to the correct one.

  • 10 years ago

    Heidesign - It showed up that time. I apparently just needed to be more specific in the search box.

    Got that pillow finished earlier. I was able to keep the zipper and all is well. I was getting ready to start another pillow and just discovered that place sold me the wrong size bobbins also. It won't spin and thread. I'm just going to order bobbins and be done with it. Anyone prefer metal over plastic?

  • 10 years ago

    Check the manual to see what bobbins fit your specific machine as they shouldn't be inter-changed between plastic or metal. It is probably the plastic bobbins but there are two different heights so it depends on the specs.

    Machine manuals are available to down load if you need one also. The manual will give you the part number for the bobbin that fits your machine.

    Another option is to use the already wound bobbins used in embroidery machines. I use them all the time in my sewing machine. The thread is wound perfect on the bobbin and lasts a long time. Plus they are available in different colors. Generally, a pack of 10 bobbins is around $5.00.

    Hope that helps!




  • 10 years ago

    I agree with 4heidesign. That is not a zipper foot in your photo. This will not work. The zipper foot looks exactly like the photo in 4heidesign's post. The needle is shifted to the side to stitch through the notch.

  • PRO
    10 years ago

    Sheesback, do check your manual for your correct bobbin size! There are different sizes for each machine, and usually are not interchangeable - I’ve learned that the hard way, when stitches became irregular or stitching problems developed. With 6 machines, some with plastic and some with metal bobbins, and all different sizes for both plastic and metal, keeping track of which bobbin fits which machine became a challenge. I finally had to color-code each one!

  • 10 years ago
    last modified: 10 years ago

    Elizabeth - They sold it as a concealed zipper foot which was what I had wanted at the time. I should have worded the title of the post different.

    Beaus and Heidesign - The reason I asked plastic or metal was because when I searched my machine model on the sewing parts online places both options came up. Manual says "SA156 Bobbins which are class 15 bobbins" and "approx 7/16". The ones I bought at the place are plastic and have a J on the inside. I've used both plastic and metal with my machine. When my grandma gave it to me there were three plastic ones that I believe were the ones that came with the machine and a metal one that also worked.

    ETA - I just typed SA156 Bobbins on that site and the same two metal and plastic options came up.

    Beaus - Would the already wound bobbins work for my machine if it needs to be specific.

    Do newer machines are more "universal" parts that are interchangeable?

  • 10 years ago

    That plastic one is an invisible zipper foot. While you don't need one to put in an invisible zipper, they do make it easier to accomplish.

  • 10 years ago

    Annie - Right. I assumed concealed zipper and invisible zipper foot were the same thing so I've been saying concealed throughout this thread. The rest of the pillows I'm making with the regular zipper foot that came with my machine.

  • 10 years ago

    Yes, they will work. The bobbins come in different sizes so just match the correct height and diameter.

    Here is a link that shows the different sizes and descriptions for reference.

    http://www.thethreadexchange.com/miva/merchant.mvc?Screen=CTGY&Category_Code=prewound-bobbins

    A local sewing store that sells embroidery machines should have them available too.


  • 10 years ago

    I'm still stuck on why your presser foot won't go higher with the the zipper foot on but it does with that regular foot. Could you indulge me please, at your convenience, and take 4 pix for me, from a side view just like your second pic above. One each with the presser foot lift up and one with it down with each of those feet on so I can see the presser foot shank height both raised and lowered.

    As long as the correct height foot is on, which both of those appear to be, the shank should be able to raise and lower equally. Doesn't make sense to me.

  • 10 years ago

    Beaus - Good to know. Thank you!

    Blubird - I'll take some photos later.

    I worked on more pillows last night and the concealed zipper foot does work it just takes a little wiggling to get both the fabric and zipper under the foot. I struggled much more with the first pillow I made. In general, since I don't sew often, things always good smoother after I'm working on something a while. You can see it's not ideal to use with the machine though. FWIW, I received an email back from Brother saying they never made a concealed zipper foot for that machine.

  • 10 years ago
    last modified: 10 years ago

    Here ya go Blubird.

    Up

    Down

    Here's the side view of the concealed zipper foot. When on the machine I do have it pushed up as far as it will go before tightening.

    Here's showing how the fabric and zipper doesn't easily slide underneath. I just assumed there should be more (any!?) space. This is with the foot UP.

    Here's after a little forceful wiggling. Foot is still up.

  • 10 years ago

    Does your machine have an adjustment for increasing/decreasing pressure on the pressure foot? It would be a button or maybe a screw.

  • 10 years ago

    Thanks for those pix. Although the new zip foot still appears to be a low shank foot, that metal part may just be a drop too long. Very strange, as there are only 3 types of feet, as I mentioned above, and they all look pretty different and easily identifiable. TIs a puzzlement!