Software
Houzz Logo Print
northface99

Cleaning epoxy off granite?

10 years ago

Someone put what looks like epoxy on the surface of my granite fireplace. Anyone have suggestions on how to get it off? The fireplace guy said "chip it off", which sounds like a lot of work, and could leave chisel marks. I was thinking I'd need to get it sandblasted off...it is really very hard. (Tried to get a pic, and it just looks like a rust stain.)

Comments (14)

  • 10 years ago

    I was at HD the other day and saw some Epoxy removers in the paint stripper section. Maybe give that a look? Not sure if it would do anything to the granite.

    northface99 thanked Tech First
  • PRO
    10 years ago
    If the stripper does't work get a small angle grinder and grind it off. It should not be deep at all, if it is granite.
    northface99 thanked User
  • PRO
    10 years ago
    Sandblasting would work great too though.
    northface99 thanked User
  • 10 years ago

    Razor blade...as suggested.

    northface99 thanked chiflipper
  • 10 years ago

    Pure acetone. Soak a cotton ball and apply it to the epoxy. It will take some time, but will soften the epoxy which can then be scraped off.

  • PRO
    10 years ago
    Acetone is very much not the way to go! It will just give you a headache from all of that outgassing and evaporation. That is not what it is made for.
  • PRO
    10 years ago

    I can't imagine acetone softening epoxy, although I've soaked hard seamed solid surface bowls off with lacquer thinner. Flammable stuff, be careful.

    northface99 thanked Joseph Corlett, LLC
  • 10 years ago

    Thanks, all, for the suggestions. We are going to blast some old paint off the rafters with walnut shell dust (less destructive of wood than sand). I'll see if a whack of walnut dust will do anything for the epoxy.

  • PRO
    10 years ago

    I think it will also damage the finish around the epoxy I would do the razor then a bit of thinner to take off the last little bit , try holding an ice cube on there first

    northface99 thanked Patricia Colwell Consulting
  • PRO
    10 years ago

    Sandblasting granite?? Sounds to me like you would trade one problem for the other. Unless the surface is a raw, rough granite -- you should be able to razor blade it off with a little mineral spirits or thinner. And, in the end you may need to reseal that area to bring it back to the same finish as the rest of the space.

    northface99 thanked Cindy Sherman, CKBD
  • 10 years ago

    The fireplace is from sometime around 1930, rough granite purportedly brought from the C&O canal when the canal was abandoned. The epoxy is on the two vertical stones on the sides, right below the mantel stone. The poor fireplace has been much abused, with the epoxy (a redish brown) and the mantel has been stained some kind of black and the grout re-pointed with black stained concrete.

    Some later time I'll get the black grout out & re-point with grey grout. Also plan to remove the grates and substitute granite blocks, and take off the black stain from the mantel. Per the fireplace man, the grates are not of much value, part of a "Heatelator" system, even though they look art deco to me. In any event, they don't go with this very old log cabin.

  • 10 years ago

    That picture sure alters the dilemma.

    northface99 thanked Anne Duke
  • PRO
    10 years ago

    The photo should have been posted in the beginning .. sandblasting or using a Dremel with a sanding tip or a larger rotary type tool, even a wire brush on a drill would likely get you somewhere. I also wonder, if it was me trying to tackle this -- I would try a heat gun and see if it would soften and pull off?? That is a solid, almost indestructible type granite looking fireplace so that changes my thought of it being a more delicate-type surface.

    northface99 thanked Cindy Sherman, CKBD