Software
Houzz Logo Print
chris749

Starting Lawn Renovation

9 years ago

I am just starting my lawn renovation nad had some inquiries. My lawn was semi-decent before I started the main issue I had was there were like 50 different colors of grass from over the years people planting. I had some pretty bad bent grass like 10-10 sections. Finally I had some pretty lumpy areas that had been taken over by tall fescue. So I decided to redo it.


I just put Roundup down on the entire lawn to kill the grass after scalping it down to Eighth of an inch. The main question I have is I have been reading that I could just leave the dead grass down some mulch and slit seed underneath it. I'm wondering if this is a viable alternative since the soil is good and I haven't had any major problems other then getting that Bent grass out and achieving uniform color. Do you think it is viable to use that method or should I rake it all out till it level and plant the seed .

Comments (14)

  • 9 years ago

    chris-

    This is only my opinion but the more soil you have exposed to the grass seed you're putting down the better....so if the dead grass is covering the soil, I think it's wise to pull out as much as you can, maybe with a rented tiller from home depot?


  • 9 years ago

    No tillers!!! Use a dethatcher or aerator

  • 9 years ago

    Ok but what's the benefit vs. a tiller?

  • 9 years ago

    You don't want to change the sub soil grade & make it all lumpy, you just want to scrape some dead stuff off the top. Aerator & dethatcher do just that without causing years of bumpy lawn

  • 9 years ago
    last modified: 9 years ago

    Yeah if I leave the dead grass I would be using slice seeding so I would have exceptional soil seed contact.but I thought it might affect the amount of light that gets to the seedlings but I wasn't sure. Keep in mind I've cut the grass down to less than an inch. Or it might inhibit their root system

  • 9 years ago

    IMO you would have been much better off to spray first, then once it was dead scalp it. You see, RoundUp works by being absorbed into the leaves and from there it is transported to the roots where it kills the plant.

  • 9 years ago

    +1 forsheems. As he sort of said, you sort of screwed yourself by mowing first and then spraying the RU. You can recover and really need to slow down. Start now watering 3x per day to sprout all the weed seeds you can. Water every day for a week. That will help bring back the grasses you scalped off and did not die the first time. Then after a week, spray with RU again. Ideally you would continue watering daily to spray RU again in 2 weeks, but you're already off this program. The idea is to kill everything including all the potential weed seeds sitting on your soil.

    Then you could run the slit seeder without seed to pick up all the dead stuff. Set the slits to scar the ground about 1/8-inch deep. As you run over it you will find low spots that the slitter doesn't hit. You will also find high spots. I suggest running over the high spots over and over to loosen that soil. Then use a push broom to move the high spot soil into the low spots. Try not to get carried away with that process and create new low spots. Walk on the low spot soil to press the fluffy new soil down onto them. This is the time to perfect your soil surface. The smoother you get it now the fewer problems you will have with drainage.

    Tilling with a hand held tiller makes it almost impossible to get a good surface at the top. Tillers hop up out of the ground when they hit a root, rock, or hard spot. They dig deep when they hit sand or other soft spots. There's no way you can fix that. The result is the underlying surface is uneven. When you level the top of the soil that leaves differing depths of fluffy soil on top of the untilled profile underneath. When the fluffy soil finally settles in 3 years, it will settle to match the profile of the uneven surface below. That settling starts immediately and ends in 3 years, so your soil starts out getting bumpy and ends up really bumpy. That's why you don't till. If you had a tiller on the back of a 10,000 pound tractor, you can control that, but hand held tillers are the worst.

    Getting back to the seeding, once you have run the slit seeder over the soil without seed, you could scatter the seed by hand into the scarred up soil and get about the same results. Up to you. Either way roll the seed down to push it against the soil. If the area is small enough, just walk on it to press it down.

  • 9 years ago

    So the round up seems to be working because I am getting a lot of death in the yard. I have picked up the watering in order to sprout as much as I can and I'll be doing a Nother round up application this weekend hopefully. To clarify a comment am I to understand I should use the slit seeder to essentially rip up all the dead grass then I can rake that and dispose of it

  • 9 years ago

    Also I mis-spoke when I mentioned a "tiller"....what I meant was a power rake.

  • 9 years ago

    Almost completely dead at this point just working a few last areas. Is the best way to get the dead grass up the power rake it? And how beer do I want to get the lawn? Essentially some more stuff on top OK? Or does it need to be just dirt?

  • 9 years ago

    I would suggest something in this category with fixed blades ( power rakes/de-thatchers usually have flail or spring tines). I would not use the seed hopper however.

    http://www.homedepot.com/tool-truck-rental/Overseeder/TS-20HD/

  • 9 years ago

    Actually this is what I was planning on using… http://www.homedepot.com/tool-truck-rental/Power-Rake/TR-20HD/

    What a be better served using the over seeder though ?

  • 9 years ago

    Great tip thank you.

Sponsored
NME Builders LLC
Average rating: 5 out of 5 stars2 Reviews
Remodeling Company in New Albany, Ohio