Software
Houzz Logo Print
logan_hurt

2 way switch wired with 3 wires. Double power source?

8 years ago

All of my switches are wired with 3 black wires. Two separate source wires seem to be coming off of my service panel and into my 2 way switch.

Comments (16)

  • 8 years ago
    last modified: 8 years ago

    Good Lort! Call an electrician! Because you for sure should not touching anything without some education first.

    Start with the Readers Digest Home Improvement book. It’s my housewarming gift to all newbie homeowners.

  • 8 years ago

    Seems every switch I open up has 2 power wires ran to it, I don't understand at all. Is this normal or is there a reason for it? I am about to just unhook one wire from each switch. 1982 build. Maybe they ran wires for separate power for something such as ceiling fan? Even the hall lights and closet lights have this configuration though. Seems like a lot of excess wire was ran. Maybe a shady contractor who charged to have double wires ran?

  • 8 years ago

    I would suspect that only one of those wires comes from the power source while the other, that does not go through the switch, is carrying the power on to another device. The solitary wire, on the other side of the switch, would be carrying power to whatever that switch controls.

  • 8 years ago

    I suggest you post some photos.

  • 8 years ago
    last modified: 8 years ago

    Logan, all your switches are wired with 3 black wires? No wires of any other color? As DavidR said, post some photos.

  • 8 years ago

    I'm a total amateur but it does seem a bit unusual for SWITCHES to all have two sets of wires. Usually power goes to the device being switched, then down and back to the switch, so there is only one piece of Romex coming into the switch.

    I doubt disconnecting one will be a good idea, it's that way for some reason. You can verify whether it's actually two hot wires, or as randy said above, the second is actually carrying power to down the line. Shut off the breaker, disconnect one set of wires from the switch so they are not touching the other set (or anything else!), turn the power back on and check the voltage on the two sets of wires. I suspect you will find one set is hot and the other is not. In which case, don't mess with what isn't broken.

  • 8 years ago
    We had extra wires in a 1979 house. It turned out all the tops of the outlets were connected to the switch next to the room entrance. A real pain! We paid an electrician to come disconnect the outlets from the switch and change outlets/switches to new color while he was there.
  • 8 years ago

    sandi25: that's not an unusual setup especially for a bedroom. You want to be able to turn a lamp on as you enter the room and also be able to plug something like a clock radio in that would need continuous power to work properly.

    Just curious.....if you disconnected the outlets from the wall switch then why did you replace the switch? It's not controlling anything anymore. Might as well patch the wall and eliminate it completely.

  • 8 years ago

    sdello, they just wanted unswitched outlets so they disconnected them from the switch. they didn't want to eliminate them altogether

  • 8 years ago

    Logan, randy is likely right, but we would need to see more pictures, especially on the back of the switch. One of those is likely wired in parallel with the switch so that it runs to another source (like another switch or outlet). Instead of combining them with a wire nut and a jumper wire, they wired them both to the line of the switch.

    What are you attempting to accomplish?

    And Sophie is also right... if you're unsure of what you're doing in there, take a step back and call a pro until you learn and know what you're doing. Improper electrical work can destroy devices, homes, and families.

  • 8 years ago

    When I wired my bedrooms, I used the "split receptacle" method, connecting one outlet directly to the power and the other to the switch. As long as it is used like sdello said, no problems. But I used a dimmer switch which means that a vacuum or other motor-driven appliance plugged into the switched outlet (by mistake) wouldn't work so well, so I replaced the dimmer with a regular switch.

    I would still like an answer to my question above: "Logan, all your switches are wired with 3 black wires? No wires of any other color?"

  • 8 years ago

    I hope Logan wasn't lost in an electrical mishap. :-]

  • 8 years ago

    Now that I think about it, I wonder if he has an old house with knob and tube wiring. But since Logan seems to have vanished, at least from GW, I guess we'll never know.

  • 8 years ago

    Looks like Logan isn't paying attention any more! I couldn't see the photos he linked to on Amazon Prime - do I have to have an account to see them?

  • 8 years ago

    I think he removed the picture. It wasn't useful anyways. Too close up and not showing whatever he was trying to describe.

    I think either he had absolutely no idea how electricity works and looked into it a little and realized his error in judgement or he posted before having his morning coffee.

    Now he's too embarrassed to follow up. We will probably never hear from him again.